Electronic properties of magnetically doped nanotubes

Effect of doping of carbon nanotubes by magnetic transition metal atoms has been considered in this paper. In the case of semiconducting tubes, it was found that the system has zero magnetization, whereas in metallic tubes the valence electrons of the tube screen the magnetization of the dopants: the coupling to the tube is usually antiferromagnetic (except for Cr).     

A new method to suppress harmonics using /spl lambda//4 bias line combined by defected ground structure in power amplifiers

A new /spl lambda//4 bias line combined by a dumb-bell shaped defected ground structure (DGS) is proposed to suppress harmonics in power amplifiers. The proposed DGS bias line maintains the required high impedance even after DGS is inserted, while the width and length of the /spl lambda//4 bias line are broader and shorter than those of conventional bias lines. When the DGS bias line is used in power amplifiers, the third harmonic components as well as the second harmonic are reduced, because of the increased slow-wave effect over wide harmonic band. It is shown that the reduction of the third harmonic component, the improvement of 1 dB compression point, and power added efficiency are 26.5 dB, 0.45 dB, and 9.1%, respectively.     

Transmission performance of 10-Gb/s 1550-nm transmitters using semiconductor optical amplifiers as booster amplifiers

We have demonstrated the transmission performance of 10-Gb/s transmitters based on LiNbO/sub 3/ modulator using semiconductor optical amplifiers (SOAs) as booster amplifiers. Utilizing the negative chirp converted in SOAs and self-phase modulation induced by high optical power, we can successfully transmit 10-Gb/s optical signals over 80 km through the standard single-mode fiber with the transmitter using SOAs as booster amplifiers. SOAs can be used for booster amplifiers with a careful adjustment of the operating conditions. In order to further understand an SOA's characteristics as a booster amplifier, we model SOAs and other subsystems to verify the experimental results. Based on the good agreement between the experimental and simulation results, we can find the appropriate parameters of input signals for SOAs, such as extinction ratio, rising/falling time, and chirp parameter to maximize output dynamic range and available maximum output power (P/sub o,max/).     

Theoretical analysis of cladding-mode waveguide dispersion and its effects on the spectra of long-period fiber grating

A new method to control the free spectral range (FSR) of a long-period fiber grating (LPFG) is proposed and theoretically analyzed. As the refractive index decreases radially outward in the silica cladding by graded doping of fluorine, waveguide dispersion in the cladding modes was modified to result in the effective indexes change and subsequently the phase-matching conditions for coupling with the core mode in a LPFG. Enlargement of the FSR in a LPFG was theoretically confirmed.     

Enhanced thermal stability of a sputtered titanium-nitride film as a diffusion barrier for capacitor-bottom electrodes

The effect of a thin RuO_x layer formed on the Ru/TiN/doped poly-Si/Si stack structure was compared with that on the RuO_x/TiN/doped poly-Si/Si stack structure over the post-deposition annealing temperature ranges of 450–600°C. The Ru/TiN/poly-Si/Si contact system exhibited linear behavior at forward bias with a small increase in the total resistance up to 600°C. The RuO_x/TiN/poly-Si/Si contact system exhibited nonlinear characteristics under forward bias at 450°C, which is attributed to no formation of a thin RuO_x layer at the RuO_x surface and porous-amorphous microstructure. In the former case, the addition of oxygen at the surface layer of the Ru film by pre-annealing leads to the formation of a thin RuO_x layer and chemically strong Ru-O bonds. This results from the retardation of oxygen diffusion caused by the discontinuity of diffusion paths. In particular, the RuO_x layer in a nonstoichiometric state is changed to the RuO₂-crystalline phase in a stoichiometric state after post-deposition annealing; this phase can act as an oxygen-capture layer. Therefore, it appears that the electrical properties of the Ru/TiN/poly-Si/Si contact system are better than those of the RuO_x/TiN/poly-Si/Si contact system.     

GaN and AlGaN high-voltage rectifiers grown by metal-organic chemical-vapor deposition

In this paper, we report the study of the electrical characteristics of GaN and AlGaN vertical p-i-n junctions and Schottky rectifiers grown on both sapphire and SiC substrates by metal-organic chemical-vapor deposition. For GaN p-i-n rectifiers grown on SiC with a relatively thin “i” region of 2 μm, a breakdown voltage over 400 V, and forward voltage as low as 4.5 V at 100 A/cm² are exhibited for a 60-μm-diameter device. A GaN Schottky diode with a 2-μm-thick undoped layer exhibits a blocking voltage in excess of ∼230 V at a reverse-leakage current density below 1 mA/cm², and a forward-voltage drop of 3.5 V at a current density of 100 A/cm². It has been found that with the same device structure and process approach, the leakage current of a device grown on a SiC substrate is much lower than a device grown on a sapphire substrate. The use of Mg ion implantation for p-guard rings as planar-edge terminations in mesageometry GaN Schottky rectifiers has also been studied.     

Evaluating the impact of CASE: an empirical comparison of retrospective and cross-sectional survey approaches

The purpose of this paper is to evaluate two methods of assessing the productivity and quality impact of Computer Aided Software Engineering (CASE) and Fourth Generation Language (4GL) technologies: (1) by the retrospective method; and (2) the cross-sectional method. Both methods involve the use of questionnaire surveys. Developers' perceptions depend on the context in which they are expressed and this includes expectations about the effectiveness of a given software product. Consequently, it is generally not reliable to base inferences about the relative merits of CASE and 4GLs on a cross-sectional comparison of two separate samples of users. The retrospective method that requires each respondent to directly compare different products is shown to be more reliable. However, there may be scope to employ cross-sectional comparisons of the findings from different samples where both sets of respondents use the same reference point for their judgements, and where numerical rather than verbal rating scales are used to measure perceptions.     

Presupposition failure — A comedy of errors

Presuppositions of utterances are the pieces of information you convey with an utterance no matter whether your utterance is true or not. We first study presupposition in a very simple framework of updating propositional information, with examples of how presuppositions of complex propositional updates can be calculated. Next we move on to presuppositions and quantification, in the context of a dynamic version of predicate logic, suitably modified to allow for presupposition failure. In both the propositional and the quantificational case, presupposition failure can be viewed as error abortion of procedures. Thus, a dynamic assertion logic which describes the preconditions for error abortion is the suitable tool for analysing presupposition.