Two-Dimensional Green's Function for Thermal Stresses in a Semi-Layer Under a Point Heat Source

We present specific new expressions for thermal stresses as Green's functions for a plane boundary value problem of steady-state thermoelasticity for a semi-layer. We also obtain new integration formulas of Green's type, which determine the thermal stresses in the form of integrals of the products of the given distributed internal heat source, boundary temperature, and heat flux and derived kernels. Elementary functions results obtained are formulated in a theorem, which is proved using the harmonic integral representations method to derive thermal stresses Green's functions, which are written in terms of Green's functions for Poisson's equation. A new solution to particular two-dimensional boundary value problem for a semi-layer under a boundary constant temperature gradient is obtained in explicit form. Graphical presentations for thermal stresses Green's functions created by a unit heat source (line load in out-of-plane direction) and by a temperature gradient are also included.     

Thermoeconomic optimization of subcooled and superheated vapor compression refrigeration cycle

An exergy-based thermoeconomic optimization application is applied to a subcooled and superheated vapor compression refrigeration system. The advantage of using the exergy method of thermoeconomic optimization is that various elements of the system—i.e., condenser, evaporator, subcooling and superheating heat exchangers—can be optimized on their own. The application consists of determining the optimum heat exchanger areas with the corresponding optimum subcooling and superheating temperatures. A cost function is specified for the optimum conditions. All calculations are made for three refrigerants: R22, R134a, and R407c. Thermodynamic properties of refrigerants are formulated using the Artificial Neural Network methodology.     

Pt nanoparticles synthesized with new surfactants: improvement in C1–C3 alcohol oxidation catalytic activity

Platinum electrocatalysts were prepared using PtCl₄ as a starting material and 1-decylamine, N,N-dimethyldecylamine, 1-dodecylamine, N,N-dimethyldodecylamine, 1-hexadecylamine, and 1-octadecylamine as surfactants. These surfactants were used for the first time in this synthesis to determine whether the primary and/or tertiary structure and/or chain length of the surfactants, affects the size and/or activity of the catalysts in C₁–C₃ alcohol electro-oxidation reactions. Electrochemical measurements (cyclic voltammetry and chronoamperometry) indicated that the highest electrocatalytic performance was observed for the Pt nanocatalysts that were stabilized by N,N-dimethyldecylamine, and this has a tertiary amine structure with a short chain length (R = C₁₀H₂₁). The high performance may be due to the high electrochemical surface area, Pt(0)/Pt(IV) ratio, %Pt utility, and roughness factor (R _f). X-ray photoelectron spectroscopy, X-ray diffraction, atomic force microscopy, and transmission electron microscopy were used to determine the parameters that affect the catalytic activities.     

Calculations of neutron-induced production cross-sections of W up to 20 MeV

Neutron-induced cross-sections for the stable isotopes ^{180,182,183,184,186}W in the energy region up to 20 MeV have been calculated. Calculations were made with the codes CEM03.01 and ALICE/ASH, using the following models: the Dubna version of the intranuclear cascade model for the cascade stage of interaction; the hybrid, the geometry dependent hybrid and the exciton model for the pre-equilibrium component; the Hauser–Feshbach and the Weisskopf–Ewing statistical models for the equilibrium component. Effects of some important model parameters such as level density parameter and pairing correction were investigated. Calculated cross-sections were compared with available experimental data in the literature and with ENDF/B-VI T = 300 K and JENDL-3.3 T = 300 K evaluated data libraries.     

Improved interfacial adhesion with the help of functional polyhedral oligomeric silsesquioxanes in silicone rubber/rayon fiber composites: Physical,mechanical, thermal,and morphological properties

The aim of this article is to improve the interfacial adhesion between silicone rubber (SR) and Rayon fiber by the help of functional hybrid POSS nanoparticles. Two POSS types were compared, octavinyl-POSS (O-POSS) and methacryl-POSS (M-POSS), having reactive  CC double bonds that can impart in peroxide crosslinking. O-POSS is nonpolar, whereas M-POSS is polar and is able to make H-bond with Rayon fibers. POSS type and their concentrations were examined as the experimental parameters. H-adhesion tests indicated that both POSS types enhanced the adhesion of SR composites to Rayon fibers compared with control recipe. Specifically, slightly higher values were obtained with the use of M-POSS. It was observed that both O-POSS and M-POSS slowed down the curing rate but increased the degree of crosslinking. The cure extent of O-POSS containing composites was found to be higher than that of M-POSS containing ones. Thermal gravimetric analyses revealed that thermal stability of SR composites was significantly improved by the addition of POSS particles. Higher char yield and degradation temperatures were obtained with O-POSS at higher loadings with respect to M-POSS. The POSS distribution at lower loading levels was found to be homogenous for both POSS types as observed from scanning electron microscope and transmission electron microscope.     

Fatigue damage in composite cylinders

In this study, optimal angle‐ply orientation of symmetric composite cylinders under fatigue loading is investigated. The fiber‐reinforced plastic cylinders were manufactured from E‐glass/epoxy. The layers were manufactured symmetrically in [±75°]₂, [±60°]₂, [±55°]₂, and [±45°]₂ orientations. Burst pressure of filament‐wound composite cylinders under alternating pure internal pressure was measured experimentally. Internal fatigue pressure testing method was applied to the composite cylinders in close‐ended condition. For this study, a PLC controlled hydraulic pressure testing machine has been employed. The static burst pressure values of specimens were measured; subsequently, fatigue test pressure was applied in 70, 60, and 50% stress levels of burst pressure for each orientation. Damage propagations of the composite cylinders on these stress levels were observed as whitening, leakage, and final failure for [±60°]₂, [±55°]₂, and orientations. When the damage propagation of [±75°]₂ angle‐ply cylinder was observed, whitening and leakage did not occur and final failure occurred suddenly. Stress‐cycle curves obtained from the tests are given in graphics. Experimental results reveal that variation in stress levels and the winding angles have considerable effects on final failure cycles, which is also presented graphically. The optimum winding angle for the composite pressure cylinders or vessels under internal fatigue pressure load was obtained as [±45°]₂ orientation. POLYM. COMPOS., 2010. © 2009 Society of Plastics Engineers     

Synthesis and characterization of a Zr‐containing silicate‐based epoxy‐functional polymer nanocomposite system

As a continuation of efforts to explore the potential of certain types of polymer nanocomposites to be successful candidates as dental restoration/adhesion materials, a Zr‐containing and organically modified silicate‐based material system with epoxy functionality was prepared by use of a sol–gel synthesis method, and UV light‐ and visible light (VL)‐curing processes. Comparative influences of the synthesis and processing parameters on the mechanical, thermal, and microstructural/nanostructural properties of the system were detailed. Zr‐containing species proved to more effectively catalyze the epoxy polymerization/crosslinking reactions than those containing Ti. Incorporation of Zr into the nanocomposite network led to significantly advanced mechanical properties. An elastic (Young's) modulus value of 23 MPa was achieved. The system with relatively high Zr content was successfully obtained, which also had higher thermal stability. Overall observations and results suggested that Zr content, and the UV light‐ or VL‐curing process could be capitalized on to modify the structure, and to improve the final properties of these material systems, which indicated a prospective opportunity for this material system to be utilized in dental restoration/adhesion applications. POLYM. ENG. SCI., 55:792–798, 2015. © 2014 Society of Plastics Engineers     

Creating a high-quality wool-oriented Turkish merino herd and investigation of mechanical and dyeability properties of fabrics produced from Turkish merino in comparison with Australian merino

Today, the need for quality wool suitable for worsted fabric production in the world is mainly met by Australian merino wool. In Turkey, which has a significant sheep population, in addition to domestic breeds, approximately 10% of the total sheep population (around four million head) is composed of merino cross breeds. However, the fleece quality is far from meeting Australian merino wool standards. Therefore, the aim of this study is to ensure a merino herd with high-quality wool in Turkey. For this aim, by carrying out field studies in the Thrace region of Turkey where Turkish Merino sheep are widely bred, sheep with fleece that can meet the demands of the worsted industry were determined. As a result of field studies in which thousands of sheep were examined, it was determined that 43 female and 10 male sheep had fleece that would meet these standards. Then the breeders of the sheep, which had quality fleece, were persuaded and these sheep were purchased, and “Turkey's wool-oriented Turkish (Karacabey) Merino Herd” consisting of 30 sheep and three rams was formed in the farm of Tekirdağ Namık Kemal University. In the second part of this study, a 100% wool fabric produced by using Australian merino was taken as a reference and it was aimed to produce the same fabric from Turkish merino wool. For this aim, the wool-oriented Turkish Merino herd, which was bred at the university farm for 1 year, was shorn in May 2022. Then, Turkish and Australian merino wools were first converted into worsted yarn and then into woven fabric. The results of mechanical (tensile strength, pilling, abrasion resistance, felting shrinkage, Hofmann dimensional change, bending stiffness) and dyeability (dye-uptake, CIE L*a*b* and colour yield (K/S) values; washing, rubbing and light fastness values) properties of fabrics produced from Turkish and Australian merino wool is presented.