Laser-induced fluorescence-cued, laser-induced breakdown spectroscopy biological-agent detection

Methods for accurately characterizing aerosols are required for detecting biological warfare agents. Currently, fluorescence-based biological agent sensors provide adequate detection sensitivity but suffer from high false-alarm rates. Combining single-particle fluorescence analysis with laser-induced breakdown spectroscopy (LIBS) provides additional discrimination and potentially reduces false-alarm rates. A transportable UV laser-induced fluorescence-cued LIBS test bed has been developed and used to evaluate the utility of LIBS for biological-agent detection. Analysis of these data indicates that LIBS adds discrimination capability to fluorescence-based biological-agent detectors. However, the data also show that LIBS signatures of biological agent simulants are affected by washing. This may limit the specificity of LIBS and narrow the scope of its applicability in biological-agent detection.     

Electroanalytical behavior of poly-L-lysine dendrigrafts at the interface between two immiscible electrolyte solutions

In this work, the electrochemical behavior of nonredox-active poly-L-lysine dendrigraft molecules of four different generations was investigated at the interface between two immiscible electrolyte solutions (ITIES). The influence of the dendrigraft generation on the electrochemical response, sensitivity of the calibration curves, and limit of detection was studied. Cyclic voltammetry at the ITIES revealed that the sensitivity increased (1840 to 25?800 nA μM(-1)) and the limit of detection decreased (11.10 to 0.65 μM) as the dendrigraft generation increased from generation G2 through to generation G5, respectively. The results are compared to those for protein voltammetry at the ITIES. Our studies suggest that the sensitivity expected for a synthetic ionized macromolecule can be predicted on the basis of its net charge and its diffusion coefficient. However, electrochemistry at the ITIES demonstrates a greater sensitivity toward proteins, which is attributed to their tertiary structure.     

Sputtered tungsten-based ternary and quaternary layers for nanocrystalline diamond deposition

Many of today's demanding applications require thin-film coatings with high hardness, toughness, and thermal stability. In many cases, coating thickness in the range 2-20 microm and low surface roughness are required. Diamond films meet many of the stated requirements, but their crystalline nature leads to a high surface roughness. Nanocrystalline diamond offers a smoother surface, but significant surface modification of the substrate is necessary for successful nanocrystalline diamond deposition and adhesion. A hybrid hard and tough material may be required for either the desired applications, or as a basis for nanocrystalline diamond film growth. One possibility is a composite system based on carbides or nitrides. Many binary carbides and nitrides offer one or more mentioned properties. By combining these binary compounds in a ternary or quaternary nanocrystalline system, we can tailor the material for a desired combination of properties. Here, we describe the results on the structural and mechanical properties of the coating systems composed of tungsten-chromium-carbide and/or nitride. These WC-Cr-(N) coatings are deposited using magnetron sputtering. The growth of adherent nanocrystalline diamond films by microwave plasma chemical vapor deposition has been demonstrated on these coatings. The WC-Cr-(N) and WC-Cr-(N)-NCD coatings are characterized with atomic force microscopy and SEM, X-ray diffraction, X-ray photoelectron spectroscopy, Raman spectroscopy, and nanoindentation.     

Using solution thermodynamics to describe the dispersion of rod-like solutes: application to dispersions of carbon nanotubes in organic solvents

We report a simple model describing the solubility of rods in solvents, expressing the final result explicitly in terms of the surface entropy and the enthalpy of mixing. This model can be combined with any expression for the mixing enthalpy depending on the requirements. For example, in one instance it predicts the dispersed concentration of rods to decrease exponentially with the Flory-Huggins parameter of the dispersion. Using a different enthalpy function, it predicts a Gaussian peak when concentration is plotted versus solvent surface energy. The model also suggests specific solvent-rod interactions to be important and shows the dispersed concentration to be very sensitive to ordering at the solvent-rod interface. We have used this model to describe experimental results for the concentration of dispersed nanotubes in various solvents. Qualitative agreement with these predictions is observed experimentally. However, we suggest that the fact that quantitative agreement is not found may be explained by solvent ordering at the nanotube surface.     

Copper electrodeposition onto the dendrimer-modified native oxide of silicon substrates

Adherent copper films were electrochemically grown onto the native oxide surfaces of Si wafers modified by the adsorption of polyamidoamine (PAMAM) dendrimers. Metallic nuclei of copper grow at isolated nucleation sites, associated with adsorbed dendrimers, and film coalescence can be observed above a metal thickness of about 10,000 monolayers (∼2.5 μm). Film microstructure depends on the deposition mode; higher coverage and better adhesion were obtained by galvanostatic control of the deposition process. It is hypothesized that reduction of Cu²⁺ ions complexed with functional groups of the chemisorbed dendrimer leads to the formation of metallic copper nuclei, and that metal films grow from these nuclei. Further improvement of this process may open the way to the direct integration of metal electrodeposition with silicon microfabrication processes and selective deposition by dendrimer patterning.     

Real-time detection and identification of aqueous chlorine transformation products using QTOF MS

A screening technique has been developed that allows the rapid, real-time detection and identification of major transformation products of organic contaminants during aqueous oxidation experiments. In this technique, a target contaminant is dissolved in buffered water and chlorinated by the addition of sodium hypochlorite to give a free chlorine residual of 3 mg/L. Solution from the reaction vessel is combined with methanol and pumped directly into the electrospray ionization source of a quadrupole time-of-flight mass spectrometer (QTOF MS). The real-time decay of the target contaminant and the formation/decay of transformation products are then monitored using the QTOF MS. Subsequently, accurate mass measurements with internal mass calibration (<5 ppm mass error) and product ion scans are employed to identify these transformation products. Unlike other techniques, it requires no liquid chromatography, derivatization, or quenching of residual chlorine, all of which can interfere with transformation product analysis. To validate the technique, aqueous chlorination experiments were performed on triclosan, a previously studied environmental contaminant. Earlier research showing that triclosan underwent chlorine addition to form mono- and dichlorinated transformation products was successfully reproduced, demonstrating the feasibility of the technique. In addition, the technique revealed the formation of a stable oxygen radical-containing transformation product resulting from the oxidation of either mono- or dichlorinated triclosan. This triclosan transformation product was determined to have an empirical formula of C12H4O3Cl4 with 3.9 ppm mass error. Furthermore, atorvastatin, a commonly prescribed medication and environmental contaminant, was subjected to aqueous chlorination and studied with the technique. Atorvastatin underwent hydroxylation to form two transformation products with the empirical formulas C33H34FN2O6 (1.8 ppm mass error) and C26H29O5NF (2.9 ppm mass error).     

Low-loss waveguides fabricated in BK7 glass by high repetition rate femtosecond fiber laser

For the first time femtosecond-laser writing has inscribed low-loss optical waveguides in Schott BK7 glass, a commercially important type of borosilicate widely used in optical applications. The use of a variable repetition rate laser enabled the identification of a narrow processing window at 1 MHz repetition rate with optimal waveguides exhibiting propagation losses of 0.3 dB/cm and efficient mode matching to standard optical fibers at a 1550 nm wavelength. The waveguides were characterized by complementary phase contrast and optical transmission microscopy, identifying a micrometer-sized guiding region within a larger complex structure of both positive and negative refractive index variations.     

Fluorescence detection and identification of tagging agents and impurities found in explosives

The detection and identification of 2,4,6-trinitrotoluene (TNT), 1,3,5-trinitro-1,3,5-triazacyclohexane (RDX), and pentaerythritol tetranitrate (PETN) vapors have proven to be difficult and challenging due to the low vapor pressures of these high explosives. Detecting higher vapor pressure impurity compounds found in TNT and possible tagging agents mandated to be added to plastic explosives (RDX and PETN) would allow for easier vapor detection. The higher vapor pressure nitro compounds of interest are considered to be non-fluorescent; however, once reduced to their amino analogs, they have relatively high quantum yields. The standard reduction products, the reduction products obtained in solution, and the reduction products obtained in vapor phase were analyzed by conventional fluorescence, synchronous luminescence, and derivative spectroscopy. The nitro analogs of the isomers 1,3-diaminobenzene, 1,2-diaminobenzene, and 1,4-diaminobenzene are found as impurities in TNT. We provide for the first time the synchronous luminescence derivative spectra of these isomers; including their individual spectra and a spectrum of an isomeric mixture of the three. Using the standard reduction products associated with these isomers and other aromatic amines, our data suggest that the vapors of two signature impurities, 1,3-dinitrobenzene and 2,4-dinitrotoluene (2,4-DNT), minor impurity compounds, and two possible tagging agents, 2-nitrotoluene (2-NT) and 4-nitrotoluene (4-NT), can be detected and selectively identified using our fluorescence approach. To prove our methodology, we show that we were able to generate, collect, and reduce 2-NT, 4-NT, and 2,4-DNT vapors to their amino analogs. Using our fluorescence approach, these vapors could be detected and selectively identified both individually and in a mixture. Collectively, our data indicate that our method of detecting and identifying higher vapor pressure explosive-like compounds could potentially be used to detect and identify low vapor pressure explosives such as TNT, RDX, and PETN.     

ZnO thin films prepared by a single step sol-gel process

ZnO thin films were prepared on fused silica from a single spin-coating deposition of a sol-gel prepared with anhydrous zinc acetate [Zn(C₂H₃O₂)₂], monoethanolamine [H₂NC₂H₄OH ] and isopropanol. Crystallization annealing was performed over the range 500 to 650 °C. X-ray analysis showed that thin films were preferentially orientated along the [002] c-axis direction of the crystal. The films had a transparency of greater than 85% in the visible region for sol-gels with a zinc content of up to 0.7 M and exhibited absorption edges at ∼ 378 nm. The optical band-gap energy was evaluated to be 3.298-3.306 eV. Photoluminescence showed a strong emission centered at ca. 380 nm along with a broad yellow-orange emission centered at ca. 610 nm. Single step sol-gel thin film deposition in the film thickness range from 80 nm to 350 nm was demonstrated. The effect of sol-gel zinc concentration, film thickness and crystallization temperature on film microstructure, morphology and optical transparency is detailed. A process window for single spin coating deposition of c-axis oriented ZnO discussed.