Crystallite growth characteristics in superfine zirconia powders and compacts

Crystallite growth characteristics of coprecipitated superfine zirconia powders have been investigated. It was found that the crystallite growth in powders follows a cubic law at 800 and 1000°C; however, the crystallite size data for compacts of both Y-TZP and YSZ cannot be fitted with a traditional parabolic or cubic law, but with a linear relation between crystallite size and the logarithm of time. In addition, it was also found that the degree of agglomeration of the powders can affect the crystallite growth.     

锆(Ⅳ)-3,5-diBr-PADAP-安替比林三元配合物的分光光度研究与应用

本文提出在安替比林存在下,以3,5-diBr-PADAP为显色剂,分光光度测定微量锆的新方法。在pH1～2的HCl介质中,锆(W)与试剂和安替比林形成配合比为1:1:1的红色三元配合物,最大吸收值在615nm波长处,摩尔吸光系数ε=1.35×10~5。锆(Ⅳ)量在0～25μg/25ml范围内,遵守比尔定律。方法简单、快速、准确。若采用钽试剂—苯萃取法分离共存离子,可适用于钽铌矿和合金中痕量锆的测定。     

贵冶动力中心二期反渗透系统改造

本文阐述对贵冶动力车间二期反渗透进行改造的成功实践 ,主要从反渗透系统设计、反渗透系统中容易出现的问题及解决方法等进行介绍。     

天津德景住宅与商业

因：用地为东西向长达470m的长条形，其北侧紧邻城市干道。     

CFD Simulation of Liquid Film Flow on Inclined Plates

A two‐phase flow CFD model using the volume of fluid (VOF) method is presented for predicting the hydrodynamics of falling film flow on inclined plates, corresponding to the surface texture of structured packing. Using the proposed CFD model the influence of the solid surface microstructure, liquid properties and gas flow rate on the flow behavior was investigated. From the simulated results it was shown that under the condition of no gas flow the liquid flow patterns are dependent on the microstructure of the plates, and proper microstructuring of the solid surface will improve the formation of a continuous liquid film. It was also found that liquid properties, especially surface tension, play an important role in determining the thin‐film pattern. However, there are very different liquid film patterns under the action of gas flow. Thinner liquid films break easily, but thicker liquid films can remain continuous even at higher gas flow rates, which demonstrates that all factors affecting the liquid film thickness will affect the liquid film patterns under conditions of counter‐current two‐phase flow.     

Development of an end-point detector for parylene deposition process

Parylene is an emerging material for MEMS. It is an organic material that is grown by using the chemical vapor deposition method at room temperature. The deposition thickness is commonly controlled by the amount of solid-phase dimer loaded in a sublimation chamber. In a conventional deposition machine, the end point of the process is designated by the moment the dimer is exhausted. However, this end-of-process criterion does not offer precise, repeatable control of film thickness. We present the results of the development of an in situ end-point detector for a Parylene chemical vapor deposition process. The detector is based on the thermal transfer principle and can be implemented on commercial parylene deposition systems with minimal system modification. Such a sensor enables a user to stop the deposition when a targeted thickness is reached. The end point detector is very simple to implement on existing parylene deposition systems. A series of such sensors with different target deposition thickness would allow extraction of the actual deposition rate within a deposition run.     

西气东输工程用X70热轧板卷屈服强度检测值波动大的探讨

对西气东输工程用X70热轧板卷检验过程中出的屈服强度σ0.5波动大的情况进行了分析，认为拉伸试样弯曲是主要原因。这一问题可通过反复压平试样，确保试样的平直度以及适当提高钢的强度的方法加以解决。     

Hydrothermal Synthesis of Magnesium Aluminate Platelets

Magnesium aluminate (MgAl₂O₄) platelets were first synthesized by hydrothermal treatment of γ-AlO(OH) in a magnesium nitrate aqueous solution at 400°C. The platelets are 100–200 nm in width and 25 nm in thickness. The influence of temperature, the anions of the magnesium salt, the amount of magnesium salt, and precursor pH on the formation of such structure was investigated. The experimental results indicated that the anions of the magnesium salt and precursor pH could have a significant influence on the growth of MgAl₂O₄. MgAl₂O₄ formation followed the in situ transformation mechanism, which was the reason why the MgAl₂O₄ crystallites had a platelet morphology.     

探索小森

对于小森公司来说，最近几年在中国的销售业绩相当不错，小森印刷机在中国市场的占有率一直在稳步提高。中国的印刷市场正在高速增长，而小森能够取得如此佳绩，最根本的原因是积极应对世界印刷市场发展趋势，把深度满足用户的需求放在了首位，正如小森的企业理念——让客户感动。     

用αβ谱仪测量人工αβ放射性气溶胶体积活度的试验研究

本文介绍了用αβ谱仪系统同时测量αβ谱、实现Ｒｎ／Ｔｈ子体补偿、确定超铀α核素气溶胶体积活度及人工放射性气溶胶总β体积活度的技术途径。利用ＲａＡ、ＲａＣ′ａ峰的二段时间计数可确定空气中ＲａＡ、ＲａＢ、ＲａＣ的气溶胶体积活度，相应的，也能给出ＲａＢ、ＲａＣ对总β计数的贡献。根据一般环境条件下的平衡比，用ＴｈＣ′的。计数修正Ｔｈ子体对αβ测量的影响。￣［２３９］ｐｕ或／和￣［２４１］Ａｍ人工核素的α计数，可通过两段时间分别扣除ＲａＡ、ＲａＣ′拖尾的方法确定；β计数分别扣除Ｒｎ／Ｔｈ子体β贡献即可确定。在本文规定的测量条件下，对室内天然Ｒｎ子体水平在１５Ｂｑ／ｍ￣３以下，超铀α核素气溶胶体积活度的测量下限可达到０．１Ｂｑ／ｍ￣３；即使在７５Ｂｑ／ｍ￣３环境下，人工核素总β的测量下限也可达ｌＢｑ／ｍ￣３以下。