Pullout tests of epoxy-coated reinforcement in concrete

The bond strength and slip of epoxy-coated reinforcing bars in concrete have been evaluated by carrying out single pullout and double pullout tests. In extended single pullout tests, slip measurements were made while tensile force was applied to reinforcing bars embedded in concrete. In double pullout tests, 20 cycles of load were applied at levels of steel stress between zero and 0·5 times characteristic steel strength. Strains were measured by electrical resistance strain gauges glued inside the bars. Both epoxy-coated and uncoated bars were used in the investigation, to obtain comparative results. The strain gradient along the bar was found to be less for the coated reinforcement. In general, the epoxy coating was found to increase slip in bond and thereby reduce the bond performance of coated bars.     

On the performance advantage of multitaper spectral analysis

The performance advantage of multitaper spectral analysis is quantified relative to weighted overlapped segment averaging (WOSA). To make the comparison of these two nonparametric spectral estimators, theoretical performance measures are derived in terms of leakage, variance, and resolution. The methods are then compared by evaluating each measure in turn, while requiring the other two measures to be equal. The results show that multitaper analysis always performs better than WOSA. For example, given the same leakage and resolution, multitaper analysis can have three-quarters to one-half the variance of WOSA. Given the same resolution and variance, multitaper analysis can exhibit a 10-20-dB leakage advantage over WOSA. These and other results provide compelling evidence for greater use of multitaper analysis in situations for which a nonparametric spectral estimator is appropriate     

Approximate methods of identifying dynamic systems

Translated from Izmeritel'naya Tekhnika, No. 7, pp. 8–9, July, 1992.     

Characteristics of a far-infrared molecular laser optically pumped by a high-power CO2 laser

A molecular far-infrared (FIR) laser optically pumped by a high-power CO₂ laser, which is a powerful source for testing detectors and mixers and for FIR spectroscopy, is constructed and the performance is examined through experiments. At frequencies between 580GHz and 4.25THz, FIR output power is more than 20～30m W by pumping power of 35～81W. Amplitude stability of ±3% is obtained at 100m W output at 2.52THz for over 30 minutes when the FIR tube is cooled at 5°C by a chiller. As an application to testing mixers, FIR laser lines up to 4.25 THz are detected by Schottky barrier diodes (SBD). Further, using a SBD, performance of absolute frequency stability at 693GHz of HCOOH oscillation is measured by harmonic mixing with a 115.5GHz millimeter wave from a phase-locked Gunn oscillator. The resultant center-frequency stability is 100kHz per 10 minutes.     

An alternative approach to weight function evaluation for an orthotropic crack

The use of the analytically decoupled near-tip displacement solutions as an alternative approach, is presented in this paper for the efficient finite element evaluation of the decoupled weight functions for an orthotropic 2-D crack. This alternative approach has been validated by directly comparing the prior weight function results with a symmetric mesh approach in the crack-tip neighborhood, and indirectly by comparing the calculated stress intensity factors (K_I(II)) values using the computed weight functions with available K_I(II) solutions of the 2-D mixed mode orthotropic cracks. In addition, this approach with analytically decoupled near-tip displacement solutions for calculating weight functions at all locations, can facilitate further extension of weight function evaluations to a more general 2-D anisotropic crack.     

Kinetic model of block photopolymerization of glycidyl methacrylate to high conversion

The kinetics of glycidyl methacrylate block polymerization to high conversion was experimentally investigated with variations of the photoinitiator concentration, temperature, and power of UV illumination. The kinetic curves of this polymerization process contain three characterized sections of coordinates of “conversion–time,” namely: The first one is practically linear to a conversion of ≈0.5, the second represents, by itself, the autoacceleration process, and the third presents the autodecelation process. An additional peculiarity of such a polymerization process is poor reproduction of the kinetic measurements. This reproduction does not correspond to instrumental error. Derivation of a kinetic model for block linear polymerization was done. This model is, quantitatively, in good agreement with all the data of the experimental material. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 3556–3569, 2002     

低压铝箔交流腐蚀研究

在３０Ｈｚ频率下，通过铝箔在ＨＣｌ＋Ｈ２ＳＯ４＋ＨＮＯ３＋Ｈ３ＰＯ４体系中的交流腐蚀，研究腐蚀液组成中腐蚀主体及缓蚀剂对铝箔腐蚀的作用，探讨腐蚀过程中电源频率、腐蚀液温度、电流密度及腐蚀时间对铝箔腐蚀的影响。腐蚀液组成的配比恰当，有利于比容的提高。在特定的频率下采用合适的腐蚀液温度、适宜的电流密度和腐蚀时间可以提高铝箔的静电容量。     

Enhancement of heat and mass transfer in a plane channel with turbulizers on one of the walls

The effect of turbulizing asperities positioned on one of the walls of a plane channel on the intensity of exchange processes near a smooth wall with injection of different working media is studied experimentally. Translated from Inzhenerno-Fizicheskii Zhurnal, Vol. 70, No. 3, pp. 404–408, 1997.