丙烯压缩机振动偏高原因分析及解决方法

在丙烯腈生产过程中,发现其关键设备丙烯制冷压缩机轴振动值不断上升,针对此种情况对机组进行了分析与探讨,并制定解决方案。结果表明压缩机转子未采用正确的动平衡试验是造成轴振动的主要原因。采取正确的检维修方案是保证机组长周期运行、装置长周期运行的关键。     

溅渣护炉工艺探讨

从炉渣对炉衬和溅渣层的侵蚀机理入手,提出了兼顾冶金和溅渣双重效果的直接造渣工艺,探讨了终渣碱度、MgO、FeO含量等的调整范围,分析了溅渣操作中枪位、时间等的控制和炉底上涨的原因,以期更好地运用溅渣护炉技术。     

注凝析油开采稠油的地质工艺

在西西伯利亚俄罗斯油田开展了注凝析油开发稠油的研究，现场实验结果表明，注入25%的凝析油，可使其混合液粘度达到原高粘油粘度的1/60，以俄罗斯油田为例，探讨了注凝析油矿场试验的可行性，预测了凝析油的用量和可能产出的油量，并对原油外输提出了一系列更换工艺设备的要求。     

Formation of mushroom-like ZnO microcrystals through a solution calcination process

Mushroom-like ZnO microcrystals have been prepared via a solution calcination route, using Zn(NO₃)₂ as Zn source in the absence of any surfactants, templates or catalysts. This is the first example to prepare mushroom-like crystals as semiconductors, which are expected to show particular physical properties. The ZnO products were investigated by X-ray powder diffraction (XRD), scanning electron microscopy (SEM), Raman spectroscopy and photoluminescence (PL) spectrum measurements. A suitable concentration of Zn(NO₃)₂ solution was important for the growth of the mushroom-like products. The reported synthetic procedure is straightforward and inexpensive, and thus can be readily adopted to produce large quantities of mushroom-like ZnO microcrystals.     

基于计算机视觉的油管螺纹非接触智能检测

针对传统接触式油管螺纹参数测量方法的缺点,开发了基于计算机视觉的油管螺纹非接触智能检测系统。在简述非接触智能检测测量原理和测量系统组成的基础上,详细介绍了利用非接触智能检测系统对油管螺纹参数进行测量的方法,其中包括图像的采集及预处理,图像的锐化,螺纹边缘轮廓的检测与提取,螺纹尺寸的测量计算与对比分析。     

雷达仿真系统中电磁干扰环境的仿真设计和实施

雷达仿真系统是为检测雷达设备的抗干扰能力以及在各种电磁环境下的工作性能而设计的，包括有源干扰和无源干扰的模拟仿真。本文阐述了无源干扰即杂波的散射模型和仿真过程；从同步脉冲干扰的基本原理出发，阐明在雷达工作环境仿真系统中距离拖引、速度拖引、虚假目标等同步脉冲有源干扰的设计和实施过程；并针对工作在搜索和跟踪交替模式下的相控阵雷达提出自适应综合干扰方式；最后分析并总结了系统仿真时为真实、有效地模拟电磁干扰环境应注意的关键问题。     

多排数翅片管空冷器风阻特性的数值模拟

本文对多排数翅片管空冷器空气侧的风阻特性进行了数值模拟.利用商用软件Fluent进行数值计算,结合经验公式和已有的实验数据,分析了不同入口风速下,阻力的变化规律以及流动阻力和温度变化对模拟计算的影响.     

Vibration thresholds for fretting corrosion in electrical connectors

Single frequency vibration tests were used to induce fretting corrosion in tin alloy plated contacts. The samples used in this study were connectors consisting of 25 pairs of mated pin and socket contacts. Experimental results for a variety of vibration levels, frequencies, and wiring tie-off lengths are presented. The experiments consisted of running a series of vibration tests at each frequency where the excitation level was stepped through a range of g-levels. During each test run contact resistance was monitored as a performance characteristic. The results exhibit threshold behavior at each frequency for the onset of fretting degradation. Typically a plateau region was observed where similar g-levels produced similar fretting rates. It was also found that outside the plateau region the g-levels varied according to the dynamic behavior of the mechanical system. In addition, a transfer matrix model was used to analyze these results. An empirical fit of the data correlated well with the model when damping was used. This analysis revealed the importance of the bending moment induced at the contact interface as a result of excitation levels and tie-off configurations. Consequently, it is concluded that dynamic response of the mechanical system under various g-levels and tie off configurations can greatly impact the performance of a connector system subjected to vibration stresses.     

浅析特殊人群的住宅设计

特殊人群住宅的设计要点及对特殊人群住宅建设的几点建议。     

高能超声处理对锡锑包晶合金凝固组织的影响

在锡锑包晶合金的凝固过程中导入高能超声，不仅显著细化α相和β相晶粒组织，同时使具有立方晶体特征的β相组织有明显的球化趋势，消除了密度偏析，分析了高能超声细化凝固组织的机理。