Improvement in thermal endurance of D-mannitol as phase-change material by impregnation into nanosized pores

This paper describes the control of the melting point and improvement of the thermal endurance of D-mannitol (melting point T_m = 440 K) as a phase-change material (PCM) by vacuum impregnation of the PCM into nanosized pores of porous SiO₂ grains. First, we examined the effects of the average pore size (D_P) of porous SiO₂ on T_m and latent heat (L) of PCM/SiO₂ composites. Second, we investigated the thermal endurance of the composites using constant temperature kinetics based on L of the PCM and composites. Third, we performed cyclic tests of melting and freezing on the composite to evaluate leakage of the PCM. Thermophysical properties of the samples were measured by differential scanning calorimetry, and the following results were obtained: (1) The impregnation ratio of the composites was 0.91–0.99; therefore, almost all pores were completely filled with the PCM. (2) T_m shifted to lower temperature with smaller D_P, reaching 413 K in case of the PCM/SiO₂ composite with a D_P of 11.6 nm (3) T_m was derived as a function of D_P from the Gibbs–Thomson equation taking into account the existence of a nonfreezing layer on the surface of the pore wall. (4) The duration of thermal degradation of the PCM/SiO₂ composite with D_P = 11.6 nm was three times longer than that of the pure PCM at a temperature that is 10 K more than each melting point. (5) The PCM/SiO₂ composite with D_P = 11.6 nm can use as a shape-stable PCM composite without leakage of PCM.     

Measurement of High-Temperature Elastic Properties of Ceramics Using a Laser Ultrasonic Method

Young's modulus and Poisson's ratio of SiC ceramics at temperatures >1400°C were obtained using a laser ultrasonics method that included a Fabry-Pérot interferometer (LUFP). At temperatures <1000°C, Young's modulus and Poisson's ratio measured using the LUFP method agreed well with those measured using standard contact methods, such as the resonance method and the ultrasonic pulse method. These results showed that the LUFP method is a powerful tool for measuring high-temperature elastic properties of advanced ceramics in a noncontact manner.     

Morphology‐dependent electrocatalytic activity of nanostructured Pt/C particles from hybrid aerosol–colloid process

An optimum nanostructure and pore size of catalyst supports is very important in achieving high catalytic performances. In this instance, we evaluated the effects of various carbon nanostructures on the catalytic performances of carbon‐supported platinum (Pt/C) electrocatalysts experimentally and numerically. The Pt/C catalysts were prepared using a hybrid method involving the preparation of dense, hollow, and porous nanostructured carbon particle via aerosol spray pyrolysis followed by microwave‐assisted Pt deposition. Electrochemical characterization of the catalysts showed that the porous Pt/C catalyst gave the best performance; its electrochemical surface area was much higher, more than twice than those of hollow or dense Pt/C. The effects of pore size on electrocatalysis were also studied. The results showed the importance of a balance between mesopores and macropores for effective catalysis with a high charge transfer rate. A fluid flow model showed that good oxygen transport contributed to the catalytic activity. © 2015 American Institute of Chemical Engineers AIChE J, 62: 440–450, 2016     

Homogeneous Strain Introduction Using Reciprocation Technique in High-Pressure Sliding

Metallurgical and Materials Transactions A - This study examines strain distribution occurring in the high-pressure sliding (HPS) processing for rods of pure Al and an AZ61 alloy. The strain...     

Effects of V content on hydrogen storage properties of V–Ti–Cr alloys with high desorption pressure

Hydrogen storage is one of the most important issues to realize hydrogen society especially for on-board usage. Recently, high-pressure metal hydride (MH) tank attracts many attentions due to its high volumetric hydrogen storage density and relatively easy heat management. To emphasize its merits, further improvements of properties of MH, such as capacity, hydrogen desorption capability at low temperature and durability, are required. In this paper, V–Ti–Cr alloys of V-rich compositions were investigated with perspective of increasing of hydrogen desorption pressure and durability. In both of 60at%V–Ti–Cr and 80at%V–Ti–Cr alloys, good relationship between hydrogen desorption pressure and Ti content was observed. In comparing with 60at%V–Ti–Cr alloys, 80at%V–Ti–Cr alloys showed good durability. It is quite notable that relationship between limitation line (upper substitution limit of Ti by Cr without degradation of hydrogen capacity) and desorption pressure for V–Ti–Cr ternary system with V-rich composition is clarified. And also, it is revealed that in the case of V–Ti–Cr ternary system, not only Ti/Cr ratio but also V content is important factor to obtain alloys with high hydrogen desorption pressure. 75at%V–5at%Ti–Cr as-cast sample showed good durability, hydrogen desorption capability at low temperature and relatively high effective hydrogen capacity simultaneously.     

Ion beam induced luminescence of polyethylene terephthalate foils under MeV H and He ion bombardment

The evolution of the ion beam induced luminescence (IBIL) of the polyethylene terephthalate (PET) foils was studied under the irradiation of H and He ions of MeV energy. The optical and chemical changes of the samples were also examined by photo-stimulated luminescence and optical absorption measurements after the irradiation. A prominent broad emission peak of IBIL appeared at around 380 nm, and its intensity monotonically decreased during the ion irradiation. The decay curves of the emission intensity were quantitatively explained as a function of the electronic energy deposition of the incident H and He ions. On the contrary, to the decrease of the main emission peak, a growth of new peaks was observed in the wavelengths between 500 and 600 nm.     

Sweep‐out flow of film condensation on vertical plates with horizontal grooves

We have investigated fluid flow characteristics of film‐wise condensation on vertical plates with horizontal periodic grooves. Condensate stays at the edge of the grooves due to the surface tension. The condensate starts to flow, however, when the balance between the surface tension and the condensate's own weight is broken. It is found that the condensate flows downward successively and periodically from the top part of the plate as a group. In addition, we have obtained the relation between the frequencies of the periodic flow and the degree of sub‐cooling for two different pitches of the grooves. © 2009 Wiley Periodicals, Inc. Heat Trans Asian Res; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/htj.20249