High‐Performance,Monolithic Polyaniline Electrochemical Actuators

New polyaniline (PANI) asymmetric membranes were fabricated using a phase‐inversion technique with hexane as the coagulation bath. These membranes exhibit a dense structure with macrovoids distributed asymmetrically throughout the cross‐section. A stress–strain study demonstrated that the Young's modulus (1.421 GPa) and strain at break (7.6 %) of the new PANI asymmetric membranes prepared from hexane are approximately 12 and 4 times higher, respectively, than the values reported previously for the PANI integrally skinned asymmetric membranes (ISAMs) (123 MPa Young's modulus and 1.8 % strain at break). Furthermore, monolithic electrochemical actuators based on a single PANI asymmetric membrane were constructed, and a bending movement of up to 20 Hz was experimentally recorded in a hydrochloric acid aqueous solution. A lifetime of over 329 500 cycles was determined for these actuators at a ± 2° angular displacement (5 Hz). The lifetime is limited by a bending fatigue that creates a transversal crack on the PANI membrane at the air–water interface. Control over the actuator movement is also manifested by the linear dependences of the bending angle on the charge and of the angular velocity on the current. These relationships are independent of both the kind of applied electric signal and the frequency used.     

Possibilities and extension of XRD material response analysis in failure research for the advanced evaluation of the damage level of Hertzian loaded components

Due to clearly distinguishable damage symptoms, it is differentiated between the surface and sub‐surface failure mode of rolling bearings. Material states red out by X‐ray diffraction (XRD) residual stress measurements point to a variety of loading conditions especially at raceway surfaces that are associated with several competing failure mechanisms. The corresponding lifetime reduction can range from the lower fatigue strength region to material ratcheting in extreme cases. Relevant position of the microstructural changes and nature of the failure mechanisms are characterized. The time alteration of the XRD material parameters measured at or near the surface and at the depth of the maximum equivalent stress correlates, in a different manner, with the statistical parameter of the 10 % bearing life. Both failure modes are illustrated by concrete examples. Contaminated lubricant and boundary lubrication, which represent practically important surface‐induced failures, are discussed in more detail. Gray staining, i.e. shallow pitting, often occurs without distinct indication of global material aging by means of XRD characteristics. Here, scanning electron microscopy observations and electron microprobe analyses point to corrosion fatigue as acting surface failure mechanism. The interaction between material and lubricant under complex loading regimes particularly of mixed friction and corrosion opens further failure research areas in the field of tribology.     

Lipase‐catalyzed dynamic kinetic resolution of (R,S)‐fenoprofen thioester in isooctane

A lipase‐catalyzed enantioselective hydrolysis process under in situ racemization of the remaining (R)‐thioetser substrate with trioctylamine as the catalyst was developed for the production of (S)‐fenoprofen from (R,S)‐fenoprofen 2,2,2‐trifluoroethyl thioester in isooctane. Detailed investigations of trioctylamine concentration on the enzyme activation and the kinetic behavior of the thioester in racemization and enzymatic reactions were conducted, in which good agreement between the experimental data and theoretical results was observed. © 2002 Society of Chemical Industry     

Determination of assimilable organic carbon (aoc) in ozonated water with acinetobacter calcoaceticus

The effect of ozone application in drinking water on the production of assimilable organic carbon (AOC) was evaluated. The typical procedure to determine AOC is suggested by van der Kooij, which is the method of bacterial growth measurement by colony‐forming units using the strain P17 and/or NOX. The bacterial indicator species used for this study is Acinetobacter calcoaceticus which was isolated and identified while ozonating Nakdong river water. This strain could never be isolated from the raw water, but this strain was the predominant isolate in the ozonated water. Within a short incubation time, this organism was found to replicate well on acetate and oxalate as the sole carbon sources. The yield coefficients of this organism for acetate and oxalate are the same order of magnitude as the value of P17 and NOX. With full‐scale experiments, A. calcoaceticus concentration was found to increase after ozonation, but did not decrease upon chlorination. In laboratory‐scale experiments with Yongsan river water, aldehyes were found to be produced in proportion to the ozone dose. The raw water contains low concentrations of aldehydes, but has a high AOC concentration. A correlation between aldehyde production and AOC production was observed in the tested water with ozonation.     

Growth of high-quality GaSb by metalorganic vapor phase epitaxy

The growth of nominally undoped GaSb layers by atmospheric pressure metalorganic vapor phase epitaxy on GaSb and GaAs substrates is studied. Trimethylgallium and trimethylantimony are used as precursors for the growth at 600°C in a horizontal reactor. The effect of carrier gas flow, V/III-ratio, and trimethylgallium partial pressure on surface morphology, electrical properties and photoluminescence is investigated. The optimum values for the growth parameters are established. The carrier gas flow is shown to have a significant effect on the surface morphology. The optimum growth rate is found to be 3–8 μm/ h, which is higher than previously reported. The 2.5 μm thick GaSb layers on GaAs are p-type, having at optimized growth conditions room-temperature hole mobility and hole concentration of 800 cm² V⁻¹ s⁻¹ and 3·10¹⁶ cm^-3, respectively. The homoepitaxial GaSb layer grown with the same parameters has mirror-like surface and the photoluminescence spectrum is dominated by strong excitonic lines.     

Effect of degumming on the tensile properties of silkworm (Bombyx mori) silk fiber

Forcibly reeled silkworm (Bombyx mori) silk was used to study how exposure to a degumming treatment (boiling in distilled water for 30 min) affects tensile properties. Because forcibly reeled and naturally spun fibers exhibit comparable mechanical behavior, the results can be generalized to material obtained conventionally from cocoons. The effects of degumming include: a decrease in the initial elastic modulus, a decrease in the stress at the proportional limit (yield strength), a change in the qualitative shape of force‐displacement curves, and significant qualitative and quantitative variability in force‐displacement data from samples subjected to nominally identical degumming histories. Immersion in water at room temperature or heating in air at 100°C for 30 min are both qualitatively equivalent to a 30‐min degumming treatment in boiling water, in terms of the effect on silk tensile properties. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 84: 1431–1437, 2002; DOI 10.1002/app.10366     

Structure and damping properties of polydimethylsiloxane and polymethacrylate sequential interpenetrating polymer networks

By using the technology of the sequential interpenetrating polymer network, a series of novel damping materials based on a polydimethylsiloxane (PDMS)/polyacrylate (PAC) matrix with polymethacrylate (PMAC) were synthesized. They have a controllable broad transition peak spanning the temperature range of 150–220°C and the medial value of loss factor with maximum of 0.35–0.60. Dynamic mechanical analysis (DMA), differential scanning calorimetry (DSC), and atomic force microscopy (AFM) were applied to analyze and characterize the transition behavior and the microphase structure of the materials. It was found that the size and height of a transition peak at both the low‐ and the high‐temperature zones change as a function not only of the concentration of PMAC and PDMS but also of the kind of PMAC; simultaneously, the low‐ temperature behavior was also governed by the crystallization of PDMS. The content of the crosslinking agent exerts a significant influence on the configuration of the curves of the transition peaks. AFM shows a characteristic phase morphology of double‐phase continuity containing a transition layer and domain less than 1 μm, indicating that the interwoven multilayer networks are the key to incorporation of the immiscible components and form a broad damping functional region. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 85: 545–551, 2002     

Synthesis and characterization of novel copolymers with the trimethylsilyl group for deep‐UV photoresists

N‐(4‐Acetoxyphenyl) maleimide (APMI) and three kinds of comonomers bearing a trimethylsilyl group were copolymerized at 60°C in the presence of azobisisobutyronitrile (AIBN) as an initiator in 1,4‐dioxane to obtain the three IP, IIP, and IIIP copolymers. These copolymers were removed from the acetoxy group in a transesterification process into new IVP, VP, and VIP copolymers with a pendant hydroxyl group. Two modified processes were adopted to prepare photoresists using these copolymers. The first process involved mixing the dissolution inhibitor, o‐nitrobenzyl cholate, with the new copolymers. Second, o‐nitrobenzyl cholate was introduced into the copolymers using 1,8‐diazabicyclo[5.4.0]undec‐7‐ene (DBU) in dimethylformamide (DMF). The cyclic maleimide structure is responsible for the high thermal stability of these copolymers. After irradiation using deep–UV light and development with aqueous Na₂CO₃ (0.01 wt %), the developed patterns showed positive images and exhibited good adhesion to the silicon wafer without using any adhesion promoter. The resolution of these resists was at least 0.8 μm and an oxygen‐plasma etching rate was 1/5.3 to that of hard‐baked HPR‐204. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 2791–2798, 2002; DOI 10.1002/app.10255     

Preparation of core–shell type nanoparticles of diblock copolymers of poly(L‐lactide)/poly(ethylene glycol) and their characterization in vitro

Core–shell type nanoparticles of poly(L ‐lactide)/poly(ethylene glycol) (LE) diblock copolymer were prepared by a dialysis technique. Their size was confirmed as 40–70 nm using photon correlation spectroscopy. The ¹H‐NMR analysis confirmed the formation of core–shell type nanoparticles and drug loading. The particle size, drug loading, and drug release rate of the LE nanoparticles were slightly changed by the initial solvents that were used. The drug release behavior of LE core–shell type nanoparticles showed an initial burst during the first 12 h and then a sustained release until 100 h. The degradation behavior of LE block copolymer nanoparticles was divided into three phases: the initial rapid degradation phase, the stationary phase, and the rapid degradation phase until complete degradation. It was suggested that lidocaine release kinetics were predominantly governed by the diffusion mechanism in the initial burst phase and after that by both of the diffusion and degradation mechanisms. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 85: 2625–2634, 2002