Determination of internal state variables and constitutive modeling for Type 316 stainless steel

The purpose of this study is to develop an approach for unified constitutive modeling based on experimentally determined back stress and overstress. Back stress and overstress were experimentally determined for Type 316 stainless steel at 600°C, by analyzing the unloading curve for the stress-strain response of cyclic strain tests. The result has indicated that the cyclic strain hardening behavior is mainly caused by hardening in the back stress. A phenomenological unified constitutive model in which the back stress and drag stress are taken as the internal state variables is proposed, and has been shown that this model is able to simulate the cyclic inelastic behavior.     

International intercomparison of horn gain at X-band

An international intercomparison of horn gain and polarization measurements at X-band has previously been completed. There were seven participating laboratories with the National Institute of Standards and Technology serving as the pilot laboratory. Two X-band pyramidal standard gain horns with a nominal gain of 22 dB served as the traveling standards. Quantities measured included on-axis fixed frequency gain at 8, 10, and 12 GHz, swept frequency gain between 8-12 GHz and polarization characteristics at the three fixed frequencies. All laboratories performed the fixed frequency-gain measurements. The swept-frequency and polarization measurements were optional, with four laboratories performing swept-frequency measurements and three laboratories measuring polarization. The results of the gain measurements generally agreed within the reported uncertainties which were of the order of 0.1 dB or less     

Clustering based on multiple paths

This paper deals with a separation of strongly touching clusters using a concept of n-connectedness between pattern pairs, i.e., the number of paths between patterns. This new concept is similar to the concept of n-connectedness of graphs. Classification algorithms based on the number of independent paths and edge-disjoint paths are presented. It is shown that the latter has a transitivity. Finally, a simpler algorithm, i.e., a classification method based on the total number of paths, is presented. The proposed algorithm may be seen as an intermediate one between the ordinary connectedness algorithm and the maximal complete subgraph (MCS) algorithm.     

The MHD effect and its relaxation process on electric current in the electrolysis of ferricyanide reduction and ferrocyanide oxidation

The electrolytic reduction of ferricyanide and the electrolytic oxidation of ferrocyanide have been carried out with exposing the magnetic field of 1000 or 1800 gauss. The current clearly increased after the magnetic exposure. The maximum current was obtained when the magnetic flux directed in parallel with the surface of electrode. These are speculated in terms of magnetohydrodynamic mechanism. The current decrease caused by relaxation process was observed after the removal of magnetic flux. The relaxation time obtained was temperature-dependent. Therefore the values of apparent transition energy, E_trans, were determined from the Arrhenius' plots of relaxation time against temperature. The magnitude of E_trans was dependent on the concentration of ferricyanide or ferrocyanide, and the viscosity and the conductivity of electrolyte solution. The activation energy of viscosity of electrolyte solution was compared with E_trans. As a conclusion, it was suggested that E_trans may be influenced by the velocity of magnetohydrodynamic flow, which was controlled by the diffusion current in electrolysis and the viscosity of electrolyte solution.     

Low temperature deposition of hexagonal BN films by chemical vapour deposition

Transparent hexagonal BN films were deposited onto copper substrates from the reactant gas BCl₃-NH₃-H₂ at temperatures in the range 250–700°C. The lowest deposition temperature of the films was about 250°C. The films deposited at temperatures below 450°C were unstable in moist atmosphere and devitrified; a 20%–30% decrease in weight was observed when these films were heated above 600°C in an argon atmosphere. In contrast, the films deposited at temperatures above 600°C were very stable, decreased in weight by 1%–2% on heating and were stable in air at temperatures below 750°C.     

Development of service-oriented products based on the inverse manufacturing concept

To achieve sustainability, resource consumption and waste generation must be drastically decreased. For societal acceptance, preservation of both quality of life and corporate profits are essential. One promising approach is to shift the source of value from the amount of product sold to the quality of services the product provides. This paper describes the need for redesigning recycling systems from a manufacturing perspective and then discusses the possibility of this "servicification" of products, describing our experience with prototype development. We discuss development of product prototypes and their business, using consumer facsimile machines as an example of "service-oriented products". Traditional thought presumes that only products comprising new materials and components are valuable. Consideration of a service-oriented product can serve as a stimulus to revise this mode of thought and to control delivery and quality of disposed products. This paper also provides a life cycle simulation of the developed service-oriented business. Simulation results indicate that service-oriented business can potentially reduce environmental impact while extending business opportunities from the viewpoint of whole product life cycles.