Particles from fires—a screening of common materials found in buildings

Small combustion generated particles are known to have a negative impact on human health and on the environment. In spite of the huge amount of particles generated locally in a fire accident, few investigations have been made on the particles from such fires. In this article, 24 different materials or products, typically found in buildings have been exposed to burning conditions in order to examine their particle generating capacity. In addition, a carbon fibre based composite material was tested in order to investigate if asbestos‐resembling particles could be generated in a fire situation. The majority of the experiments were performed in the small‐scale cone calorimeter, and some further data were collected in intermediate scale (SBI) and full scale (room‐corner) tests. Additional testing of the composite material was made in a small‐scale tubular reactor. The amount of particles and particle size distributions were measured by the use of a low‐pressure impactor and particle aerodynamic diameter sizes from 30 nm to 10 μm were measured. The results from the project show that the yield of particles generated varied significantly between materials but that the shape of mass and number size distributions were very similar for all the materials tested. The maximum amount of particles was obtained from materials that did not burn well (e.g. flame retarded materials). Well‐burning materials, e.g. wood materials, tend to oxidize all available substances and thereby minimize the amount of particles in the smoke gas. It was found that asbestos‐resembling particles could be produced from under‐ventilated combustion of the composite material tested. Copyright © 2003 John Wiley & Sons, Ltd.     

Cyberbullying on social networking sites: A literature review and future research directions

Cyberbullying on social networking sites is an emerging societal issue that has drawn significant scholarly attention. The purpose of this study is to consolidate the existing knowledge through a literature review and analysis. We first discuss the nature, research patterns, and theoretical foundations. We then develop an integrative framework based on social cognitive theory to synthesize what is known and identify what remains to be learned, with a focus on the triadic reciprocal relationships between perpetrators, victims, and bystanders. We discuss the key findings and highlight opportunities for future research. We conclude this paper by noting research contributions and limitations.     

Introduction of methyl groups to acetate substituted chain of (Z)-5-decenyl acetate,a pheromone component of turnip moth,agrotis segetum: synthesis,single-sensillum recordings,and structure-activity relationships

Methyl-substituted analogs of (Z)-5-decenyl acetate, a pheromone component of the turnip moth,Agrotis segetum, have been synthesized and studied by electrophysiological single-sensillum recordings and molecular mechanics calculations [MM2(85)]. The analogs are monomethyl substituted in the 2, 3, 4, and 5 positions and geminally dimethyl substituted in the 2, 3, and 4 positions. The methyl groups have been employed as space probes to study the degree of steric complementarity between the acetate-substituted alkyl chain of the pheromone component and its receptor. The electrophysiological activities, interpreted in terms of a receptor interaction model, indicate significant steric repulsive interactions between the introduced methyl groups and the receptor. This implies a high degree of complementarity between the acetate-substituted alkyl chain of the natural pheromone component and its receptor.Schiff., Lepidoptera: Noctuidae.     

Determination of the vapor pressures of moth sex pheromone components by a gas chromatographic method

The vapor pressures of decyl acetate, five decenyl acetate isomers, (Z)-7-dodecenyl acetate, and (Z)-9-tetradecenyl acetate have been determined at three to six temperatures in the interval 25–45 °C by a gas Chromatographic method suitable for accurate measurements of the low vapor pressures of moth sex pheromone components at biologically relevant temperatures. The vapor pressure values at 30.5 °C are 3.80 Pa for decyl acetate, 4.08–5.40 Pa for the decenyl acetate isomers, 0.562 Pa for (Z)-7-dodecenyl acetate, and 0.094 Pa for (Z)-9-tetradecenyl acetate. The vapor pressures of the decenyl acetates show a small but significant dependence on the double bond position. Four of the compounds in this study, 10Ac,Z5–10Ac,Z7–12Ac, andZ9–14Ac have recently been identified as sex pheromone components of the turnip moth,Agrotis segetum. Large differences between the mole percentages of the component as found in liquid extracts of female abdominal tips and the corresponding mole percentages in the vapor phase are predicted.     

Harnessing the Excellent Mechanical,Barrier and Antimicrobial Properties of Zinc Oxide (ZnO) to Improve the Performance of Starch-based Bioplastic

ABSTRACT

The inherent properties of starch which are poor mechanical properties and its hydrophilicity that leads to poor long-term water absorption, fostered the incorporation of additives into starch-based bioplastic to enhance its mechanical and barrier properties. Zinc oxide (ZnO) nanoparticle as a lightweight material that is biocompatible, nontoxic, cost-effective and exhibit strong antibacterial activity can be considered as nano reinforcement of starch-based bioplastic. The present work studied the reinforcing effect of ZnO on the physical, mechanical and antibacterial properties of starch-based bioplastic. Bioplastic was prepared by melt-mixing starch and glycerol (3:1, w/w) with ZnO (1%, 2%, 3%, 4% and 5%, w/w). Bioplastic density and water contact angle increased with the increase of ZnO concentration. Bioplastic with the addition of 4% ZnO showed the lowest moisture content of 3.45%. Moreover, the decomposition temperature of bioplastic with ZnO increased slightly which indicated the higher stability. Mechanical properties evaluation showed that bioplastic with addition of ZnO had higher tensile strength than that without ZnO where 4% ZnO exhibited the highest tensile strength of 10.29 MPa with elongation of 5.69%. Cross-section microstructure after tensile test showed that ZnO was fairly dispersed in starch matrix that implied the increase of the mechanical properties of bioplastic. FTIR spectra exhibited that the intermolecular interaction in bioplastics occurred through C–H, C=O, C–O–H and O–H groups. In addition, biodegradability tests of bioplastic showed that the growth of microbes decreased in the presence of ZnO due to the nature of ZnO as an antibacterial compound. The results showed that ZnO played a key role in reinforcing the physical, mechanical and antibacterial properties of starch-based bioplastic.     

Resource pooling for frameless network architecture with adaptive resource allocation

The system capacity for future mobile communication needs to be increased to fulfill the emerging requirements of mobile services and innumerable applications. The cellular topology has for long been regarded as the most promising way to provide the required increase in capacity. However with the emerging densification of cell deployments, the traditional cellular structure limits the efficiency of the resource, and the coordination between different types of base stations is more complicated and entails heavy cost. Consequently, this study proposes frameless network architecture (FNA) to release the cell boundaries, enabling the topology needed to implement the FNA resource allocation strategy. This strategy is based on resource pooling incorporating a new resource dimension-antenna/antenna array. Within this architecture, an adaptive resource allocation method based on genetic algorithm is proposed to find the optimal solution for the multi-dimensional resource allocation problem. Maximum throughput and proportional fair resource allocation criteria are considered. The simulation results show that the proposed architecture and resource allocation method can achieve performance gains for both criteria with a relatively low complexity compared to existing schemes.     

Gradiometric micro-SQUID susceptometer for scanning measurements of mesoscopic samples

We have fabricated and characterized micro-SQUID susceptometers for use in low-temperature scanning probe microscopy systems. The design features the following: a 4.6 mum diameter pickup loop; an integrated field coil to apply a local field to the sample; an additional counterwound pickup-loop/field-coil pair to cancel the background signal from the applied field in the absence of the sample; modulation coils to allow setting the SQUID at its optimum bias point (independent of the applied field), and shielding and symmetry that minimizes coupling of magnetic fields into the leads and body of the SQUID. We use a SQUID series array preamplifier to obtain a system bandwidth of 1 MHz. The flux noise at 125 mK is approximately 0.25 mu Phi 0/ sqrt Hz above 10 kHz, with a value of 2.5 mu Phi 0/ sqrt Hz at 10 Hz. The nominal sensitivity to electron spins located at the center of the pickup loop is approximately 200 muB/ sqrt Hz above 10 kHz, in the white-noise frequency region.     

Robotic System for Handling Infectious Clinical and Pre-Clinical Serum Samples

The Bioanalytical Laboratory at the Schering-Plough Research Institute is a service laboratory which performs drug level measurements in serum in support of pre-clinical toxicological tests, as well as human clinical trials for anti-viral compounds. A new robot system for the laboratory had two external constraints put on it, besides those typical for a robotic system: since it handled infectious serum samples, it needed to be contained within a biosafety cabinet, and all data handling and labeling were subject to regulatory oversight. The result is a robot cell consisting of a large custom biological safety hood with an integrated track mounted robot, refrigerated storage, mixing, 2-D bar code reading, and automated pipetting. In addition to the material handling hardware, sample labeling software was developed for use at sample collection sites within Schering-Plough, and at external contract laboratories.