Regime transition in viscous and pseudo viscous systems: A comparative study

A comprehensive quantitative study on the effect of liquid viscosity (1 ≤ µ_L ≤ 1149 mPa‐s) on the local flow phenomena of the gas phase in a small diameter bubble column is performed using ultrafast electron beam X‐ray tomography. The internal dynamic flow structure and the bubble size distribution shows a dual role of the liquid viscosity on the hydrodynamics. Further, the effect of solid concentration (C_s = 0.05, 0.20) on the local flow behavior of the gas phase is studied for the pseudo slurry viscosities similar to the liquid viscosities of the gas–liquid systems. The effects of liquid and pseudo slurry viscosities on flow structure, bubble size distribution, and gas phase distribution are compared. The bubble coalescence is significantly enhanced with the addition of particles as compared to the system without particles for apparently same viscosity. The superficial gas velocity at which transition from homogeneous bubbly to slug flow regime occurs is initiated by the addition of particles as compared to the particle free system for apparently same viscosity. © 2014 American Institute of Chemical Engineers AIChE J, 60: 3079–3090, 2014     

Higher Hydrocarbon Production through Oxidative Coupling of Methane Combined with Hydrogenation of Carbon Oxides

In the production of higher hydrocarbons, combining oxidative coupling of methane (OCM) with hydrogenation of the formed carbon oxides in a separate reactor provides an alternative to the currently applied methane conversion to syngas followed by Fischer‐Tropsch synthesis. The effects of CH₄:O₂ feed ratio in the OCM reactor and partial pressures of H₂ or/and H₂O in the hydrogenation reactor were analyzed to maximize production of C₂₊ hydrocarbons and reduce CO_x formation. The highest C₂₊ yield was achieved with low CH₄:O₂ feed ratio for OCM and removal of the formed water before entering the hydrogenation reactor.     

Powder coating of veneered particle board surfaces by hot pressing

The powder coating of veneered particle boards by the sequence electrostatic powder application – powder curing via hot pressing is studied in order to create high gloss surfaces. To obtain an appealing aspect, veneer sheets were glued by heat and pressure on top of particle boards and the resulting surfaces were used as carrier substrates for powder coat finishing. Prior to the powder coating, the veneered particle board surfaces were pre-treated by sanding to obtain good uniformity and the boards were stored in a climate chamber at controlled temperature and humidity conditions to adjust an appropriate electrical surface resistance. Characterization of surface texture was done by 3D microscopy. The surface electrical resistance was measured for the six veneers before and after their application on the particle board surface. A transparent powder top-coat was applied electrostatically onto the veneered particle board surface. Curing of the powder was done using a heated press at 130 °C for 8 min and a smooth, glossy coating was obtained on the veneered surfaces. By applying different amounts of powder the coating thickness could be varied and the optimum amount of powder was determined for each veneer type.     

Verfahren zur Erstellung auswertbarer Bildvorlagen für mikrovisioplastische Untersuchungen

The mechanical properties of polycristalline materials are depent on the type, the combination and the orientation of the elements in the micro structure. By means of the method of Visioplasticity assumptions are currently realized to analyse kinematic parameters inside of single grains and grain groups. Strength of the free surface of the specimen will be rough by its plastical deformation, it was difficult to register the increments of deformation of the grid. By further development of a method of picture analysis it is also possible to reproduce a 3d-surface by utilization of single light microscopical pictures.     

Rheotens-mastercurves and drawability of polymer melts

In a Rheotens experiment, the tensile force needed for elongation of an extruded filament is measured as a function of the draw ratio. For thermo-rheologically simple polymer melts, the existence of Rheotens-mastercurves is proven. Rheotens-mastercurves are invariant with respect to changes in melt temperature. Also, for polymer melts with different average molar masses, but similar molar mass distribution and branching structure, Rheotens-mastercurves are invariant to changes in the average molar mass. It is shown, by testing several polyethylenes with different molar mass distribution and different long-chain branching, that Rheotens-mastercurves allow a direct and quantitative assessment of the drawability of polymer melts under actual processing conditions, i.e. under the action of a constant tensile force and including the effects of the rheological prehistory in the extrusion die.     

A New Access to Piperidino-cyclopiperidinecarboxamides – constrained analogues of a pharmaceutical used diaminic building block

6-Piperidino-3-azabicyclo[3.1.0]hexane-6-carboxamide diastereomers 1a and 2a represent conformationally rigid analogues of 3a which is a building block in some pharmaceutical compounds. A new access to these compounds 1a and 2a was found via the cleavage of bicyclic N,N-acetal 6 with hydrocyanic acid as the stereodetermining step. Reaction of derivatives 1a and 2a with bromodiphenyl-butyronitrile 14 gave cyclopiritramide isomers 1c and 2c , respectively. Qualitative preliminary investigations showed different affinities of 1c and 2c to the opiate-μ receptor. These results were discussed on the basis of an X-ray structural analysis of cyclopiritramide isomer 2c . 1-Benzylcyclopiperidine derivatives 1d and 2d were used as model systems for studying the conformation of cyclopiritramide isomer 1c and 2c , respectively.