Single‐Step Deposition of Au‐ and Pt‐Nanoparticle‐Functionalized Tungsten Oxide Nanoneedles Synthesized Via Aerosol‐Assisted CVD,and Used for Fabrication of Selective Gas Microsensor Arrays

Tungsten oxide nanostructures functionalized with gold or platinum NPs are synthesized and integrated, using a single‐step method via aerosol‐assisted chemical vapour deposition, onto micro‐electromechanical system (MEMS)‐based gas‐sensor platforms. This co‐deposition method is demonstrated to be an effective route to incorporate metal nanoparticles (NP) or combinations of metal NPs into nanostructured materials, resulting in an attractive way of tuning functionality in metal oxides (MOX). The results show variations in electronic and sensing properties of tungsten oxide according to the metal NPs introduced, which are used to discriminate effectively analytes (C₂H₅OH, H₂, and CO) that are present in proton‐exchange fuel cells. Improved sensing characteristics, in particular to H₂, are observed at 250 °C with Pt‐functionalized tungsten oxide films, whereas non‐functionalized tungsten oxide films show responses to low concentrations of CO at low temperatures. Differences in the sensing characteristics of these films are attributed to the different reactivities of metal NPs (Au and Pt), and to the degree of electronic interaction at the MOX/metal NP interface. The method presented in this work has advantages over other methods of integrating nanomaterials and devices, of having fewer processing steps, relatively low processing temperature, and no requirement for substrate pre‐treatment.     

Thermoelectric Effect Spectroscopy and Photoluminescence of High-Resistivity CdTe:In

Thermoelectric effect spectroscopy and photoluminescence techniques were used to study the defect levels in samples from three crystals of CdTe:In grown by the vertical gradient freeze method. The main goal of the investigation was to study defects, which strongly trap charge carriers or act as recombination centers in order to eliminate them from the technological process. The main difference among detecting and non-detecting samples was the absence of electron traps with a very high capture cross-section and energy 0.6 eV to 0.7 eV, which act as lifetime killers even at low concentrations. Recently published ab initio calculations show a complex of Te antisite and Cd vacancy within this energy range.     

The slope of a transfer function

Exact and approximate equations are derived that relate the magnitude slope of a general transfer function directly to its phase angle. The result is used to derive simple conditions on stabilizability of feedback loops with right half-plane poles and zeros or dead-time.     

Relevance of the acid–base approach in prediction of adhesion properties in two‐component injection moulding

We demonstrate the use of innovative wetting method in prediction of the adhesion properties of biobased polymers for two‐component injection moulding, taking into account the acid–base surface properties of joined materials. The measurements were carried out in accordance with modified Berger method by calculation of the difference in shortened acidity parameter ΔD_short between hard and soft component. Correlation factors up to 0.99 were observed between ΔD_short and peel force. In comparison to results obtained by conventional wetting methods, high potential for the selection of components with high interface adhesion and for prediction of the functionality by the acid–base approach was demonstrated. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43048.     

Magnetic response of soils and vegetation to heavy metal pollution--a case study

Fast and cost-effective detection of industrial pollution can significantly promote its ecological, economic, and social assessment. A magnetometric method, used for qualitative determination of anthropogenic contamination, meets these requirements but needs further development in more quantitative terms. It could be used successfully in numerous cases when the heavy metals coexist with strongly magnetic iron oxide particles in the source dust. We present an integrated magnetic and geochemical study that examines the utility of magnetometric techniques for rapid, qualitative detection of metallic pollutants in soils and vegetation. The new aspect of our approach, in comparison with previously published articles on this subject, is the combined investigation (magnetic and geochemical) of both soils and vegetation, thus using an additional medium for employing the magnetometry as a pollution proxy at a site. The study area is a small (approximately 3 km2) region in the suburbs of Sofia (Bulgaria), with the main pollution source being a metallurgical factory. Soil samples have been taken from the topmost 20 cm from private gardens, located at different distances from the factory. Vegetation samples were taken from ryegrass (both leaves and roots) and leaves from two kinds of deciduous trees (maple and acacia). The results show that both vegetation and soils are characterized by enhanced magnetic properties, compared to background material, which is due to the presence of magnetite particles of anthropogenic origin accompanying heavy metal emissions. SEM images and microprobe analyses reveal the presence of a significant amount of particles, containing heavy metals (including iron) in vegetation samples taken close to the main pollution source. Correlation analyses show a statistically significant link (correlation coefficients ranging from 0.6 to 0.7) between magnetic susceptibility and the main heavy metals (Cu, Zn, Pb) in soil samples, indicating that the magnetic susceptibility can provide a proxy method for identifying the relative contribution of industrial pollution in soils and vegetation, that is reliable, inexpensive, and less time-consuming than standard chemical analyses.     

The impact of nuclear analysis on ITER design and licensing

The complexity of nuclear analysis on the design components of ITER is discussed. These analyses include the determination of several nuclear responses and it is shown that these results are not only relevant to the component under examination but have implications for the design of many other, often remote, systems. The contribution of nuclear analysis to the licensing process is discussed. An example is given of how this complexity means that the there is a large set of complementary analyses required to address the concerns of the licensing authorities. It also means that the nuclear analysis must be co-ordinated to ensure that the results are self-consistent and provide an integrated solution.     

Fluorous Iminoalditols: A New Family of Glycosidase Inhibitors and Pharmacological Chaperones

A collection of new reversible glycosidase inhibitors of the iminoalditol type featuring N‐substituents containing perfluorinated regions has been prepared for evaluation of physicochemical, biochemical and diagnostic properties. The vast variety of feasible oligofluoro moieties allows for modular approaches to customised structures according to the intended applications, which are influenced by the fluorine content as well as the distance of the fluorous moiety from the ring nitrogen. The first examples, in particular in the D ‐galacto series, exhibited excellent inhibitory activities. A preliminary screen with two human cell lines showed that, at subinhibitory concentrations, they are powerful pharmacological chaperones enhancing the activities of the catalytically handicapped lysosomal D ‐galactosidase mutants associated with GM1 gangliosidosis and Morquio B disease.     

Bioinspired pressure actuated adhesive system

We developed a dry synthetic adhesive system inspired by gecko feet adhesion that can switch reversibly from adhesion to non-adhesion with applied pressure as external stimulus. Micropatterned polydimethylsiloxane (PDMS) surfaces with pillars of 30 μm length and 10 μm diameter were fabricated using photolithography and moulding. Adhesion properties were determined with a flat probe as a function of preload. For low and moderate applied compressive preloads, measured adhesion was 7.5 times greater than on flat controls whereas for high applied preloads adhesion dropped to very low values. In situ imaging shows that the increased preload caused the pillars to deform by bending and/or buckling and to lose their adhesive contact. The elasticity of PDMS aids the pillar recovery to the upright position upon removal of preload enabling repeatability of the switch.