树脂浸渍补充增密对C/C复合材料摩擦磨损性能的影响

将CVD预增密至不同初始密度的C／C复合材料进行树脂浸渍／炭化补充增密至1.85g/cm^3，热处理后进行热物理性能的检测和不同刹车压力的摩擦磨损试验。结果表明，树脂浸渍／炭化是一种行之有效的快速致密化手段，所得制品的可石墨化性较好，导热性能也满足国外同类产品的要求；摩擦磨损试验和扫描电镜（SEM）观察结果表明，低一压力下形成的磨屑粒度明显大于高压下的磨屑，因而低压下的摩擦数高于高刹车压力下的摩擦系数。低压下的树脂炭对摩擦磨损的影响相对较大。     

直流输电线路故障对电信线路感应的计算

直流输电线路对电信线路的危险影响、影响机理和计算方法,国内外资料及文献中尚无系统的介绍,我国也尚无统一的计算、设计标准。为便于工程设计,可以采用理论计算与实测对比相结合的方法推导出的简化公式进行计算。     

应用单光子计数器测量尼龙－11的热释光

本文给出了一种适用于热蜂光测量的单光子计数器，并用该计数器对奇数尼龙－１１薄膜进行了实际测量．结果表明，本计数器完全满足测量微光（光功率＜１０－１５Ｗ）要求．     

AFRP筋混凝土粘结强度和锚固长度的试验研究

通过对27个拉拔试件和16个梁式试件的试验,探讨AFRP筋与混凝土的粘结滑移关系、粘结强度,并且综合分析其他文献的结果,提出简化的局部粘结滑移本构关系和拔出破坏模式下锚固长度的计算公式。     

Adaptive switching mean filter using conditional morphological noise detector

The adaptive switching mean (ASM) filter is proposed to remove impulse noise. The filter first identifies the corrupted pixels using conditional morphological noise detection and then removes the detected impulses using the adaptive mean filter. Simulation results indicate that the ASM filter can suppress impulse noise effectively while preserving the details in the image very well, thus providing better restoration performance than many other switching-based filters.     

Quantitative analysis of micro structural and conductivity evolution of Ni-YSZ anodes during thermal cycling based on nano-computed tomography

Understanding the mechanism of degradation in solid oxide fuel cells (SOFCs) using nickel/yttria-stabilized zirconia (Ni-YSZ) as the anode material is very important for the optimization of cell performance. In this work, the effects of thermal cycling on the microstructure of the Ni-YSZ anode are explored using the three-dimensional X-ray nano computed tomography (nano-CT) imaging technique. It is found that the average Ni particle size increased with thermal cycling, which is associated with the decreased connectivity of the Ni phase and the three-phase-boundary (TPB) length. Moreover, the conductivities of the anode samples are also reduced with the increase in thermal cycle times. The implication of these observations is discussed in terms of the relationship between the conductivity and connectivity of the Ni phase.     

Effect of graphite oxide on graphitization of furan resin carbon

Graphite oxide (GO) was used to accelerate the graphitization of furan resin carbon. The effects of the GO content and the heat-treatment temperature (HTT) on the graphitization of furan resin carbon were investigated. The X-ray diffraction results indicate that the graphitization extent of furan resin carbon increases with the increase of the GO content and the HTT.