导向钻井系统在多目标大井斜定向井中的应用

详细介绍了C-D井在钻进过程中井眼轨迹的控制过程,总结了在C-D井中使用导向钻井系统的成功经验。用1根导向马达、2套钻具组合、3只牙轮钻头顺利地完成了定向、增斜、稳斜及降斜,7个目标点一次击中,且最小靶心距仅0.99m。用15d完成了这口斜深2287.09m、井斜58.40°、水平位移903.11m的多目标定向井,钻穿目标点之多、实钻井眼剖面符合率之高、施工难度之大、速度之快,在目前国内都处于领先地位。     

Novel technique for SiO2 formed by liquid-phasedeposition for low-temperature processed polysilicon TFT

A technique for SiO₂ formation by liquid-phase deposition (LPD) at nearly room temperature for low-temperature processed (LTP) polysilicon thin-film transistor (poly-Si TFT) was developed. LPD SiO₂ film with a lower P-etch rate shows a dense structure. LPD SiO₂ also exhibits good electrical characteristics. LTP poly-Si thin-film transistors (TFTs) with LPD SiO ₂ as the gate insulator have been fabricated and investigated. Their characteristics indicate performance adequate for their use as pixel transistors in liquid crystal displays (LCDs)     

Mixed waste ferrite as a novel sorbent for carbon dioxide derived from flue gases

Ferrite is a potential sorbent for flue gases such as CO₂, H₂S and SO₂. This paper discusses the adsorption and decomposition of CO₂ into carbon by hydrogen-activated waste ferrites prepared from Berkeley Pit acid mine water (Butte, MT). The decomposition effectiveness of these waste ferrites was studied at 300 °C and compared with the synthetic magnetite obtained from ferrous sulfate solution in our laboratory. The decomposition was measured by two methods: indirectly by measuring the adsorption rate of CO₂ and directly by analysing the carbon deposited on the samples. The results indicated that the mixed waste ferrite had good affinity for the adsorption and decomposition. The CO₂ decomposition data of both sorbents fitted the first-order reaction kinetics. Even though the surface area of the magnetite was higher than that of waste ferrite, the CO₂ decomposition rate of the waste ferrite was estimated to be 2.5 times higher than that of magnetite under identical conditions. The carbon analysis deposited on the sample indicated that the CO₂ was 100% decomposed into carbon and other carbon/hydrogen compounds by the waste ferrite, whereas the conversion was 43% by the magnetite. In terms of specific adsorption of carbon, ferrite was three to five times more efficient than magnetite.     

岩石爆破的逾渗模型

本文在分析几种典型的岩石爆破损伤模型的基础上，发现岩石爆破损伤演化具有明显的逾渗效应。采用逾渗来描述岩石爆破损伤断裂这一动态过程是可行的，并提出了进一步可能的研究途径。     

An alternative approach to weight function evaluation for an orthotropic crack

The use of the analytically decoupled near-tip displacement solutions as an alternative approach, is presented in this paper for the efficient finite element evaluation of the decoupled weight functions for an orthotropic 2-D crack. This alternative approach has been validated by directly comparing the prior weight function results with a symmetric mesh approach in the crack-tip neighborhood, and indirectly by comparing the calculated stress intensity factors (K_I(II)) values using the computed weight functions with available K_I(II) solutions of the 2-D mixed mode orthotropic cracks. In addition, this approach with analytically decoupled near-tip displacement solutions for calculating weight functions at all locations, can facilitate further extension of weight function evaluations to a more general 2-D anisotropic crack.     

LaCrMnNiO系热敏陶瓷的微观结构控制

通过对不同配方、工艺下的ＬａＣｒＭｎＮｉＯ系热敏陶瓷的微观结构研究，指出材料的相组成对其宏观电性能的影响，并提出了通过复合工艺利用“过渡相”的形成，对材料的“最终相”加以控制的方法。文中列出了使用ＸＲＤ及ＸＰＳ手段对材料微观结构的分析结果及有关电性能的测试数据。     

Strain analysis of moving objects using a Fourier transform grid method

There is no good method to measure the shape and the strain distributions of a structure changing with time. We have previously proposed the Fourier transform grid method (FTGM) to measure the three-dimensional shape and surface strain distributions of stationary objects by analysing the two-dimensional grating images recorded with two cameras. In the stereoscopic method, it is very important to determine the accurate geometric parameters of the camera system. In this paper, the positions and the directions of cameras are accurately determined using the FTGM applied to images of a reference object on which a two-dimensional grating is drawn. Applications for analysing shape and strain distributions of vibrating rubber plates and a moving human skin are shown.     

晶须取向对SiCw／Al复合材料切削表面质量的影响

切削与晶须取向方向间的夹角对ＳｉＣｗ／Ａｌ复合材料切削表面质量有很大影响。当切削角为４５°时，晶须拔出和转动现象均较少，复合材料切削表面粗糙度最低。当切削角为１３５度时，晶段转动造成的撕裂破坏程度很大，复合材料切削表面粗糙度最大。