北京谱仪Ⅱ（BESⅡ）顶点探测器数据获取系统

北京谱仪（ＢＥＳⅡ）顶点探测器数据获取系统是北京谱仪数据获取系统的一部分，该子系统电子学采用快总线标准，本文描述了该系统的硬件结构和软件系统，软件包括快总线系统的微码软件和上层控制软件，该系统的死时间为１．５ｎｓ，对ＢＥＳⅡ系统总死时间的贡献小于０．５ｍｓ。     

基于公共存储器进行数据交换的高速数字图象处理系统

本文介绍了一种基于公共存储器进行数据交换的高速数字图象处理系统．给出了公共存储器的设计，描述了处理器对公共存储器的进程同步控制．     

制备2，4－二氯－5－氟苯甲酰乙酸甲酯的缩合剂及工艺研究

通过３种不同的碱来制备２，４－二氯－５－氟苯甲酰乙酸甲酯，优选得到了其最佳缩合剂甲醇钠；同时应用正交设计实验，研究了原料配比、反应时间、反应温度对收率的影响，在优选条件下收率为７８．５％。     

饲料级磷酸氢钙中氟的几种分析方法比较

本文采用茜素络合酮比色法和氟离子选择电极法对饲料磷酸氢钙进行氟的测定实验对比,得出常用的氟离子选择电极法完全可以代替经典的蒸馏比色法的结论。     

FAST MEASUREMENT OF ASH CONTENT IN COAL WASHING PLANT

The coal filter cake is a product of fine coal after floatation which has an ash content of 7-13%, water content of 30±2%, and a particle size of less than 1 mm. The ash content was measured by the intensity of the single backscattered gamma-ray, and its accuracy is mainly dependent on the energy of the gamma-ray. The 238Pu low energy photon source is selected in this work. The energy of its gamma-ray is 15 keV, which can result not only in the best sensitivity, but also in the lowest contribution to the environment radiation. The root mean square deviation of the ash measurement is±0.33% (±1σ).     

Spray deposition process study of SnO2silicon solar cells using orthogonal experimental design

With the “orthogonal experimental design” (OED), the dependence of conductivity and transparency of tin oxide films and open circuit voltage V_oc of SIS solar cells on the spray deposition process factors was studied. The OED technique was found to be a powerful method for realizing the best factor combination. Using OED, curves were obtained which clearly depict the effects of each factor on the SIS characteristics. The results of the experiments also illustrate exactly which variation in fabrication technique most affects the sheet resistance, V_oc, and film transparency. Under the optimal combination of conditions, a thin film doped with NH₄F was obtained, with about 90% transmission and a sheet resistance of about 80 Ω/□, along with an SIS structure with a V_oc of about 0.61 V.     

A new method for calculating loss coefficients [of power systems]

A method is proposed which avoids many limitations associated with traditional B-coefficient loss coefficient calculation. The proposed method, unlike the traditional B-coefficient method, is very fast and can handle line outages. The method utilizes network sensitivity factors which are established from DC load flow solutions, Line outage distribution factors (ODFs) are formulated using changes in network power generations to simulate the outaged line from the network. The method avoids the use of complicated reference frame transformations based upon Kron's tenser analysis. The necessity of data normalization used in least squares and the evaluation of the slope of &thetas;_j versus PG_n is not necessary with the proposed method. Using IEEE standard 14-bus and 30-bus systems, the method's results are compared against results obtained from an AC load flow program (LFED). The method's solution speed is compared to that of the LFED method, the base case database method and the conventional B-coefficient method based on A_jn-factor. The proposed method is easy to implement and, when compared to other methods, has exhibited good accuracy and rapid execution times. The method is well suited to online dispatch applications     

专家系统在化工中的应用进展

本文综述了近年来专家系统在化工领域的应用状况，并指出今后的发展趋势。