Ultrasound‐activated Knoevenagel condensation of malononitrile with carbonylic compounds catalysed by alkaline‐doped saponites

α,β‐Unsaturated nitriles have been synthesized by Knoevenagel condensation of a carbonylic compound with malononitrile, assisted by sonochemical irradiation. Two alkaline‐promoted clays (Li⁺‐ and Cs⁺‐exchanged saponites) have been employed as catalysts. The influence of the carbonylic compound (benzaldehyde or cyclohexanone) and the use of a solvent on the catalytic activity have been studied. Remarkable increase in the conversion values has been found when the reaction is activated by ultrasound, as compared with the thermal activation. In this green, solvent‐free procedure, α,β‐unsaturated nitriles have been produced in very high yields (97%) when the Cs⁺‐saponite is used as catalyst. Copyright © 2004 Society of Chemical Industry     

Acidogenic fermentation of blended food‐waste in combination with primary sludge for the production of volatile fatty acids

The performance of a laboratory‐scale anaerobic acidogenic fermenter fed with a mixture of blended kitchen food‐waste and primary sludge from a sewage treatment plant was investigated for the production of volatile fatty acids (VFA). The operating variables for acidogenic fermentation were kitchen food‐waste content (10 and 25 wt %), hydraulic retention time (HRT: 1, 3 and 5 days), temperature (ambient: 18 ± 2 °C, and mesophilic: 35 ± 2 °C) and pH (varied from 5.2 to 6.7). The experimental results indicated that effluent VFA concentrations and VFA production rates were higher at ambient temperature than at mesophilic conditions. The net amount of VFA with 10 wt % food‐waste increased up to 920 mg dm^?3 with an increase of HRT, but contrasting results (a decrease of 2610 mg dm^?3) were found due to the conversion of VFA into biogas in the case of 25 wt % food‐waste, which increased significantly at HRT of 3–5 days. In terms of biogas composition (CO₂ and CH₄), the organic matter was converted into CO₂ through the oxidative pathway by facultative species at low temperature while mesophilic temperature and optimum pH (6.3–7.8) played a pivotal role in increasing rate of conversion of VFA into biogas by methanogenesis. Rates of VFA production and their conversion are dependent on the food‐waste content in the mixture. Yet, the higher concentration of food‐waste (25% compared with 10%) did not produce VFA proportionally due to the increased rate of conversion of VFA into gaseous products. The maximum VFA production rate (0.318 g VFA_produced g^?1 VS_fed day^?1) was achieved in the 10 wt % food‐waste at ambient temperature and at a 5‐day HRT. Copyright © 2005 Society of Chemical Industry     

Investigation of texture effect on visual colour difference evaluation

The texture effect on visual colour difference evaluation was investigated in this study. Five colour centers were selected and textured colour pairs were generated using scanned textile woven fabrics and colour‐mapping technique. The textured and solid colour pairs were then displayed on a characterized cathode ray tube (CRT) monitor for colour difference evaluation. The colour difference values for the pairs with texture patterns are equal to 5.0 CIELAB units in lightness direction. The texture level was represented by the half‐width of histogram, which is called texture strength in this study. High correlation was found between texture strength and visual colour difference for textured colour pairs, which indicates that an increasing of 10 units of texture strength in luminance would cause a decreasing of 0.25 units visual difference for the five colour centers. The ratio of visual difference between textured and solid colour pairs also indicates a high parametric effect of texture. © 2005 Wiley Periodicals, Inc. Col Res Appl, 30, 341–347, 2005; Published online in Wiley InterScience (www.interscience.wiley.com). DOI 10.1002/col.     

Nutrient removal performance of an anaerobic–anoxic–aerobic process as a function of influent C/P ratio

The laboratory scale anaerobic–anoxic–aerobic (A²O) process fed with synthetic brewage wastewater was designed to investigate the effects of changing feed C/P ratio on the performance of biological nutrient removal (BNR) processes. In the experiment, the influent chemical oxygen demand (COD) concentration was kept at approximately 300 mg L^?1 while the total phosphorus concentration was varied to obtain the desired C/P ratio. Results showed that when the C/P ratio was lower than 32, phosphorus removal efficiency increased as C/P ratio increased linearly, while when the C/P ratio was higher than 32, the P removal efficiency was maintained at 90–98%, and effluent P concentration was lower than 0.5 mg L^?1. However, regardless of the C/P ratio, excellent COD removal (90% or higher) and good total nitrogen removal (75–84%) were maintained throughout the experiments. It was also found that very good linear correlation was obtained between COD uptake per unit P released in the anaerobic zone and C/P ratio. In addition, the P content in the wasted activated sludge increased with the decrease in the C/P ratio. Based on the results, it was recommended that the wastewater C/P ratio and its effects be incorporated into BNR design and operational procedures, appropriate C/P ratios were used to achieve the effluent treatment goals. Copyright © 2005 Society of Chemical Industry     

锂离子电池正极材料锂锰氧化物的固相合成研究进展

阐述了固相合成反应的原理，综述了锂锰氧化物的几种固相合成方法，并着重介绍了熔融渍法，多步加热法，机械化学法和微波化学法等在锂锰氧化物合成中的研究进展。     

扇形束投影域重建—再投影迭代法

本文所提出的投影域重建——再投影迭代算法可以恢复不完整的扇形束投影数据,从而实现从有限的投影数据重建图象。这种算法把滤波——反投影图象重建过程和再投影的过程纳入一个公式,仅在投影域上估算未知的投影数据,因此避免了重建过程和反投影过程中的插值运算,改善了收敛性,提高了计算精度,缩短了运算时间。模拟实验表明:即使有70％的投影数据丢失,经过两次迭代就能以令人满意的精度恢复丢失的投影数据。     

Variations in Spectral Slope in Lake Taihu,a Large Subtropical Shallow Lake in China

Spectral slope (S), describing the exponential decrease of the absorption spectrum over a given wavelength range, is an important parameter in the study of of chromophoric dissolved organic matter (CDOM) dynamics, and also an essential input parameter in remote sensing models. Furthermore, S is often used as a proxy for CDOM composition, including the ratio of fulvic to humic acids and molecular weight. The relative broad range in S values reported in the literature can be explained by the different spectral ranges and fitting methods used. A single exponential model is used to fit the S values for 17 investigations involving 458 samples in Lake Taihu from January to October in 2004. The average S value was 15.18 ± 1.39 μm⁻¹ for the range of 280–500 nm, which fell within the range reported in the literature. The frequency distribution of S value basically obeyed a normal distribution. Significant differences in S values between summer and other seasons showed that phytoplankton degradation was one of the important sources of CDOM in summer, whereas CDOM mainly came from the river input in other seasons. Furthermore, the estimated S value decreased with increasing wavelength range used in regression. The maximum and minimum values derived from the regression were 17.89 ± 1.25 μm⁻¹ and 13.62 ± 2.11 μm⁻¹ for the wavelength ranges of 280–380 nm and 400–500 nm, respectively, a decrease of 23.9%. S values significantly decreased with the increase of CDOM absorption coefficients. CDOM absorption coefficients could be more appropriately estimated from exponential model introducing the variation of S with absorption coefficients, making them useful for a remote sensing bio-optical model of Lake Taihu. DOC-specific absorption coefficient a*(λ) and the parameter M describing molecular size of the humic molecules could also be used as a proxy for the sources and types of CDOM. A general relationship was found between S and a*(λ), and M values. S increased with the decrease of DOC-specific absorption coefficient and the increase of M corresponding to the decrease of molecular weight.     

Effect of specimen size and loading conditions on spalling of concrete

Different qualities of concrete have been fire tested using different geometries of the specimens as well as different load levels and load configurations. The main objective with the study was to examine a test methodology consisting of a full‐scale test and different small scale‐tests for determining the probability of spalling and the amount of spalling of fire exposed concrete structures. A reference specimen was defined as a one‐sided fire exposed slab with the dimensions 1800 × 1200 mm² giving an exposed area of 1500 × 1200 mm². A number of concrete qualities with different probabilities for spalling, were tested using the reference specimen. These tests showed that the reference specimens worked well giving the expected test results. Small specimens were manufactured in different shapes with the same concrete as the one used in the reference tests. These small specimens were tested either at the same time as the reference specimens in the large furnace or afterwards on a small‐scale furnace where the fire exposed surface was 450 × 360 mm². The test results clearly show the increased probability and the increased amount of spalling by using external compressive loading. The results also show that by using pre‐stress through bars or wires the load can be lost due to heating of the bars/wires which results in a decreased amount of spalling. The boundary of the specimen also affects the amount of spalling. The spalling around the edges was in all tests less than the spalling on the central parts of the exposed area. It could also be noted that the spalling did not pass completely through any of the specimens. The reason for this is probably that the water/vapour could migrate out from the unexposed surface of the specimen. Copyright © 2006 John Wiley & Sons, Ltd.     

Use of Fiber Bragg Grating Sensors for Determination of a Simply Supported Rectangular Plane Plate Deformation

A measurement method has been developed to determine the full-field deformation of a simply supported plane plate under transverse load. The method utilizes strain information provided by a set of four fiber Bragg grating sensors mounted on the plate in a way that all sensors measure strains along one certain direction. The sensors were interrogated using a wavelength swept fiber laser. Utilizing the strain information and the first four terms of Navier solution of simply supported rectangular plate, the necessary parameters for determining the deflection could be computed. By substituting the values of x- and -y- coordinates of each position on the rectangle plate, the full-field deformation information can be obtained. Single-point loading tests were experimentally performed to verify the accuracy of the method.     

第七届中国国际橡胶技术展暨第一届亚洲埃森轮胎展系列报道二:橡胶机械系列报道三:橡胶检测设备

国内主要参展商 1.益阳橡机 益阳橡胶塑料机械集团有限公司在本次展会上,推出了一款GE-5实验室用密炼机,容积5升,啮合型转子,用于橡胶制品、白炭黑、特种胶的混炼.