Small-active-area germanium avalanche photodiode for single-mode fibre at 1.3 ?m wavelength

A germanium avalanche photodiode of 30 ?m active area diameter has been fabricated and tested. The multiplied dark current is as low as 5 nA at room temperature. A module using this diode and a spherical lens has been assembled and coupled with a single-mode fibre of core diameter 10 ?m. The quantum efficiency of the module is 90% at 1.3 ?m. The sensitivity is measured at 45 Mbit/s and at 1.3 ?m. Minimum detectable powers obtained for 10?11 error rate are ?51.9 dBm and ?50.7 dBm at 25°C and 50°C, respectively.     

Oscillation of a tilted circular pad on a droplet for the self-alignment process

The seesaw-oscillation of a small circular pad on a single droplet was studied both numerically and experimentally. The circular pad with a diameter of 2.0–3.8 mm onto a water or glycerol droplet with a volume of 1–10 μL, and a bottom substrate with a smaller diameter than that of the pad were used in the experiment. The pad was then tilted and then the tilting fixture was quickly removed. The pad alternately oscillated and then finally stabilized in a horizontal position. The numerical model considering the surface tension and the viscous force of the droplet was developed and calculated using the same configurations as those in the experiment. The experimental and numerical data showed good agreement not only in terms of the oscillating frequency and damping ratio but the transient motion of the circular pad and instantaneous droplet surface shape.     

Correlation between friction of articular cartilage and reflectance intensity from superficial images

The lubrication mechanism of articular cartilage is characterized by an efficient performance. In this work, friction of articular cartilage was evaluated with in-site images of articular surface. The images were captured with the laser light reflected at the interface between a prism and articular cartilage. The attenuation of reflectance was associated with the increase of the contact of collagen network of articular cartilage. The light reflectance and friction coefficient for short sliding presented a significant positive correlation. Friction tests were also carried out for short (30 s) and long (300 s) preloading times. The results indicate that depletion of fluid film is responsible for the increase of friction and the recovery of the fluid film was observed for the long preloading after the early stage of sliding.     

High-energy x-ray microbeam with total-reflection mirror optics

Total-reflection mirror optics for high-energy x-ray microfocusing have been developed, and tested in the energy range of 30-100 keV at beamline 20XU of Synchrotron Radiation Facility SPring-8. The optical system consists of a Kirkpatrick-Baez-type [J. Opt. Soc. Am. 38, 766 (1548)] focusing optics with aspherical total-reflection mirrors for the purpose of reducing the spherical aberrations. A focused beam size of 0.35 x 0.4 microm(2) has been achieved at an x-ray energy of 80 keV, and the measured spot size was less than 1 microm in the x-ray energy region below 90 keV.     

Question hard, answer simply: A comment on Storms et al. (2003).

It seems clear that, for whatever reasons, the dementia of the Alzheimer type patient group (as well as other patient groups) exhibits behavior that is different from the normal control group. G. Storms, T. Dirikx, J. Saerens, S. Verstraeten, and P. P. De Deyn (2003) rightfully argue that the observed behavior (similarity judgments) does not tell us the source (cause) of the differences between the 2 groups. Rather, the focus of the study should be placed more on finding the ways the 2 groups are different. They also point out various methodological problems in some of the previous attempts to characterize the nature of the differences. Further methodological issues in G. Storms et al.'s study are examined. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

Maturation of the posterolateral spinal fusion and its effect on load-sharing of spinal instrumentation. An in vivo sheep model

We investigated the temporal relationship among the biomechanical, radiographic, and histological properties of a posterolateral spinal fusion mass to elucidate the changes in load-sharing of the spinal instrumentation and that of the fusion mass throughout the healing process. Destabilization of the posterior spinal column and transpedicular screw fixation at the segments between the third and fourth and the fifth and sixth lumbar vertebrae was performed in twenty-four sheep. A posterolateral spinal arthrodesis with use of autologous corticocancellous bone graft was done randomly at one of the two segments; the other segment (without bone graft) served as the instrumented control. Six animals each were killed at four, eight, twelve, and sixteen weeks postoperatively. Biomechanical testing showed that the posterolateral fusion mass had increased mechanical stiffness after the fourth week. The strain on the hardware, measured with use of rods instrumented with strain-gauges, decreased significantly (p < 0.01) beginning at eight weeks. Radiographically, three independent observations of each of the six animals at each time-period showed that, although all of the fusion masses were considered solid unions at sixteen weeks, bridging of trabecular bone was noted during only ten of eighteen observations at twelve weeks, three of eighteen observations at eight weeks, and none of eighteen observations at four weeks. Computerized tomography and histomorphometric analyses demonstrated that mineralization in the fusion mass increased in a linear fashion even after eight weeks. Histologically, the fusion mass consisted predominantly of woven bone at eight weeks; thereafter, it was gradually trabeculated. CLINICAL RELEVANCE: We found a great discrepancy between biomechanical stability and histological maturation of the posterolateral fusion mass. The biomechanical properties of a stable spinal fusion preceded the radiographic appearance of a solid fusion by at least eight weeks, suggesting that immature woven bone provided substantial stiffness to the fusion mass. The spinal instrumentation was subjected predominantly to bending stress rather than to axial stress, and the load-sharing of the spinal instrumentation decreased concurrently with the development of the spinal fusion.     

Reversible crosslinking in cellulose. I. Determination of mercaptan and disulfide in modified cotton

Mercaptan and disulfide contents of modified cotton fabrics could be determined by application of Leach's polarographic method for wool, with minor modification. It was found that mercaptocellulose prepared by the reaction of tosyl cellulose and potassium thiolacetate followed by alkaline hydrolysis contained considerable amounts of disulfided in addition to mercaptain. Iodometric titration of mercaptocellulose gave a higher value of mercaptan than that obtained by the polarographic method. The mercaptan and disulfide contents and methylene blue uptake of the iodine-treated samples indicate that some of the mercaptan groups further undergo oxidation to acidic groups as a result of the iodine treatment. The spatial effect in the oxidation of mercapto groups in modified cotton is briefly discussed.     

Preparation of Pd-Ag thin films by the RF-sputtering method and its catalysis for oxidative dehydrogenation of allylic alcohols

Pd-Ag thin films were prepared by the RF sputtering method on a Pyrex glass substrate to give monophasic alloys. Oxidation of allylic alcohols using the films gave selectively , -unsaturated carbonyl compounds in the presence of O₂; highly dispersed Pd species on Ag, Pd₇Ag₉₃ showed 95% selectivity for acrolein from allyl alcohol at 473 K.     

High-strength–high-modulus polyimide fibers II. Spinning and properties of fibers

The polyimides based on 3,3′,4,4′-biphenyltetracarboxylic dianhydride (BPDA) described in Part I of this series were dissolved in p-chlorophenol and spun into fibers using a coagulating bath of ethanol. The fibers as spun had in general low tenacities and low moduli, but a heat treatment at 300–500°C under tension produced a remarkable increase in strength and modulus, and fibers with a tensile strength of 26 g/den (3.1 GPa) and an initial modulus higher than 1,000 g/den (120 GPa) could be obtained. Thus, the annealed fibers of polyimides are comparable to aramid fibers in mechanical properties. To heating in air and in the saturated steam, the polyimide fibers showed higher resistance than the aramid fibers. The polyimide fibers surpassed the aramid fibers in resistance to acid treatment and ultraviolet (UV) irradiation, but were inferior in resistance to alkali treatment. The annealed fibers of polyimides displayed distinct X-ray diffraction patterns. The chain repeat distance of 20.5 Å determined on the fibers of polyimide prepared from BPDA and o-tolidine, and 20.6 Å determined on the fibers of polyimide derived from BPDA and 3,4′-diaminodiphenyl ether are reasonable when the dimensions of monomeric units and the shapes of the molecular chains are considered. The X-ray reflections of both polyimide fibers were indexed satisfactorily on the basis of postulated unit cells.     

Radiation-induced polymerization of ethylene in a pilot plant. I. Bulk process

Radiation-induced bulk polymerization of ethylene was carried out with use of a pilot plant with a 10 liter reactor at pressures of 225–400 kg/cm², temperatures of 30–95°C, ethylene feed rates of 5–28 kg/hr, and dose rate of 3.8 × 10⁵ rad/hr. Characteristics of the process are mild polymerization conditions and capability of producing medium density polyethylene in powder form. The spacetime yield and molecular weight of polymer were in the range of 3.5 to 13.1 g/liter hr and 2.2 × 10⁴ to 14 × 10⁴, respectively. The space-time yield increased with mean residence time and 2.4 powders of pressure, and decreased with temperature. Molecular weight changed similarly with the reaction conditions. These results were consistent with those of the bench plant experiment and the scale effect was small. Polymer deposit to the reactor wall limited a period of continuous operation of the plant. The amount of deposited polymer was increased with the square of reaction time. The rate of polymer deposit was proportional to polymer concentration and to the cube of pressure. The polymer deposit cannot be solved in the bulk process.