COMPARISON AND VALIDATION OF OHM AND SCEM MEASUREMENTS FOR A FULL-SCALE COAL-FIRED POWER PLANT

Mercury emission measurements were performed at a 250 MW coal-fired power plant using the Ontario Hydro method (OHM) and semi-continuous emission monitors (SCEM). Flue gas sampling was performed at the inlet of the air preheater and at the outlet of the electrostatic precipitator. The results indicated that there is some agreement between the OHM and SCEM measurements on the total mercury species. However, the SCEM results were not always in good agreement with the OHM measurements on the elemental mercury species. These discrepancies in elemental mercury concentrations are probably the result of the differences in the location of the SCEM and OHM probes, the temperature difference between the SCEM sampling probe and the flue gas, and the nonuniformities in mercury concentration over the flue gas duct cross section. The other factor that contributed to the deviation between the SCEM and OHM measurement results is the sampling method: the SCEM measurements were performed at a single point while the OHM probe was traversed over multiple points over the duct cross section and the results were averaged. The effect of the SCEM sampling probe temperature was investigated by designing a sampling probe that could be heated to the sampled flue gas temperatures. This resulted in improvements in the accuracy of the elemental mercury measurements by the SCEM system.     

Development of macroporous calcium phosphate scaffold processed via microwave rapid drying

Porous hydroxyapatite (HA) scaffold has great potential in bone tissue engineering applications. A new method to fabricate macroporous calcium phosphate (CP) scaffold via microwave irradiation, followed by conventional sintering to form HA scaffold was developed. Incorporation of trisodium citrate dihydrate and citric acid in the CP mixture gave macroporous scaffolds upon microwave rapid drying. In this work, a mixture of β-tricalcium phosphate (β-TCP), calcium carbonate (CaCO₃), trisodium citrate dihydrate, citric acid and double distilled de-ionised water (DDI) was exposed to microwave radiation to form a macroporous structure. Based on gross eye examinations, addition of trisodium citrate at 30 and 40 wt.% in the CP mixture (β-TCP and CaCO₃) without citric acid indicates increasing order of pore volume where the highest porosity yield was observed at 40 wt.% of trisodium citrate addition and the pore size was detected at several millimeters. Therefore, optimization of pore size was performed by adding 3–7 wt.% of citric acid in the CP mixture which was separately mixed with 30 and 40 wt.% of trisodium citrate for comparison purposes. Fabricated scaffolds were calcined at 600 °C and washed with DDI water to remove the sodium hydroxycarbonate and sintered at 1250 °C to form HA phase as confirmed in the X-ray diffraction (XRD) results. Based on Archimedes method, HA scaffolds prepared from 40 wt.% of trisodium citrate with 3–7 wt.% of citric acid added CP mixture have an open and interconnected porous structure ranging from 51 to 53 vol.% and observation using Scanning electron microscope (SEM) showed the pore size distribution between 100 and 500 μm. The cytotoxicity tests revealed that the porous HA scaffolds have no cytotoxic potential on MG63 osteoblast-like cells which might allow for their use as biomaterials.     

Wood fuel use in the traditional cooking stoves in the rural floodplain areas of Bangladesh: A socio-environmental perspective

A study was conducted, using a multistage simple random sampling design, to determine the structural characteristics of the traditional cooking stoves, amount of wood fuel consumed in the rural floodplain areas in Bangladesh, and also to figure out the socio-economic and environmental consequences of wood fuel usage in the traditional cooking stove. The study showed that family size, income, amount cooked and burning hours significantly affected the amount of wood fuel used per family per year. Taking into account different family sizes, the study observed that 4.24 tonne fuelwood were consumed per family per year. The study showed that 42% of families used only biomass fuel, 5% used liquefied petroleum gas (LPG) and 53% used kerosene along with biomass fuels. The main source of biomass fuel was homestead forests (40%). It has been figured out that the incomplete combustion of biomass in the traditional cooking stove poses severe epidemiological consequences to human health and contributes to global warming. The study also showed that 83% of the respondents would prefer improved cooking stoves over traditional cooking stoves.     

Sequence analysis of a cryptic plasmid from Flavobacterium sp. KP1, a psychrophilic bacterium

A cryptic plasmid found at high copy number was isolated from Flavobacterium sp. KP1, a psychrophilic Gram-negative bacterium, cloned, and sequenced. The sequence will appear in the DDBJ/EMBL/GenBank databases under the accession number AB007196. The pFL1 plasmid is 2311 nucleotides in length with 32.7% GC content, and shows a distinctive nucleotide sequence without homology to other plasmids of similar length. The plasmid contains two open reading frames of significant length, ORFI and ORFII. ORFI encodes a protein similar to the replication proteins found in Gram-negative bacterial plasmids, Bacteroides fragilis plasmid pBI143 and Zymomonas mobilis plasmid pZM2. The putative translation product of ORFII shows homologies with plasmid recombination proteins found mainly in Gram-positive bacterial plasmids such as Staphylococcus aureus plasmid pT181.     

S-band Brillouin erbium fibre laser

A multi-wavelength Brillouin erbium fibre laser, which operates in short wavelength band (S-band), is proposed and demonstrated. The system employs both linear gain and nonlinear gain from a 20 m S-band erbium-doped fibre and a 500 m singlemode fibre, respectively, to generate an optical wavelength comb with spacing of approximately 0.084 nm. Two 80/20 couplers were used in the system as an internal feedback of generated Stokes signal to produce cascaded Brillouin Stokes for multiwavelength operation. A stable output laser comb of up to seven lines was obtained with a Brillouin pump of 3.5 mW and a 980 nm pump of 200 mW.     

Hydrothermal preparation of high saturation magnetization and coercivity cobalt ferrite nanocrystals without subsequent calcination

In this work, CoFe₂O₄ nanocrystals with high saturation magnetization (M_s) and high coercivity (H_c) have been fabricated via a simple hydrothermal method and without subsequent calcination. The resulting CoFe₂O₄ nanocrystals are characterized by X-ray diffraction, transmission electron microscopy, scanning electron microscopy, energy-dispersive X-ray spectrometry, differential scanning calorimetry and vibrating sample magnetometry. The results indicate that CoFe₂O₄ nanocrystals are single crystal and the average crystallite size is increasing with the hydrothermal temperature. The electron micrographs show that the nanocrystals are well-dispersed and possess uniform size. The shape of CoFe₂O₄ nanocrystals is transformed from spherical into rod by increasing the hydrothermal temperature. The nanocrystals show relatively high M_s of 74.8 emu g⁻¹ and H_c of 2216 Oe, as compared to previous reported results. The obtained results reveal the applicability of this method for efficiently producing well crystallized and relatively high magnetic properties CoFe₂O₄ nanocrystals as compared to other methods. More importantly, it does not require further calcination processes.     

Adsorption of methylene blue onto hazelnut shell: Kinetics, mechanism and activation parameters

The adsorption kinetics of methylene blue (MB) on the hazelnut shell with respect to the initial dye concentration, pH, ionic strength, particle size and temperature were investigated. The rate and the transport/kinetic processes of MB adsorption were described by applying the first-order Lagergren, the pseudo-second-order, mass transfer coefficient and the intraparticle diffusion models. Kinetic studies showed that the kinetic data were well described by the pseudo-second-order kinetic model. Significant increases in initial adsorption rate were observed with the increase in temperature followed by pH and initial MB concentration. The intraparticle diffusion was found to be the rate-limiting step in the adsorption process. Adsorption activation energy was calculated to be 45.6kJmol(-1). The values of activation parameters such as free energy (DeltaG(*)), enthalpy (DeltaH(*)) and entropy (DeltaS(*)) were also determined as 83.4kJmol(-1), 42.9kJmol(-1) and -133.5Jmol(-1)K(-1), respectively.     

Analysis of SO2 sorption capacity of rice husk ash (RHA)/CaO/NaOH sorbents using response surface methodology (RSM): untreated and pretreated RHA

The SO2 sorption capacity (SSC) of sorbents prepared from rice husk ash (RHA) with NaOH as additive was studied in a fixed-bed reactor. The sorbents were prepared using a water hydration method by slurrying RHA, CaO, and NaOH. Response surface methodology (RSM) based on four-variable central composite face centered design (CCFCD) was employed in the synthesis of the sorbents. The correlation between the sorbent SSC (as response) with four independent sorbent preparation variables, i.e. hydration period, RHA/CaO ratio, NaOH amount, and drying temperature, were presented as empirical mathematical models. Among all the variables studied, the amount of NaOH used was found to be the most significant variable affecting the SSC of the sorbents prepared. The SSC for sorbent prepared with the addition of NaOH was found to be significantly higher than sorbents prepared without NaOH. This is probably because NaOH is a deliquescent material, and its existence increases the amount of water collected on the surface of the sorbent, a condition required for sorbent-SO2 reaction to occur at low temperature. The effect of further treatment of RHA at 600 degrees C was also investigated. Although pretreated RHA sorbents demonstrated higher SSC as compared to untreated RHA sorbents, nevertheless, at optimum conditions, sorbents prepared from untreated RHA was found to be more favorable due to practical and economic concerns.     

Measurement of neutron capture cross-section of the Ga(n, γ)Ga reaction at 0.0536 eV energy

The neutron capture cross-section for the ⁷¹Ga(n,  γ)⁷²Ga reaction at 0.0536 eV energy was measured using activation technique based on TRIGA Mark-II research reactor. The ¹⁹⁷Au(n, γ)¹⁹⁸Au monitor reaction was used to determine the effective neutron flux. Neutron absorption and γ-ray attenuation in gallium oxide pellet were corrected in determination of cross-section. The cross-section for the above reaction at 0.0536 eV amounts to 2.75 ± 0.14 b. As far as we know there are no experimental data available at our investigated energy. So far we are the first, who carried out experiment with 0.0536 eV neutrons for cross-section measurement. The present result is larger than that of JENDL-3.3, but consistent within the uncertainty range. The value of ENDF/B-VII is higher than this work. The result of this work will be useful to observe energy dependence of neutron capture cross-sections.