Hexavalent chromium reduction by Acinetobacter haemolyticus isolated from heavy-metal contaminated wastewater

Possible application of a locally isolated environmental isolate, Acinetobacter haemolyticus to remediate Cr(VI) contamination in water system was demonstrated. Cr(VI) reduction by A. haemolyticus seems to favour the lower concentrations (10-30 mg/L). However, incomplete Cr(VI) reduction occurred at 70-100 mg/L Cr(VI). Initial specific reduction rate increased with Cr(VI) concentrations. Cr(VI) reduction was not affected by 1 or 10 mM sodium azide (metabolic inhibitor), 10 mM of PO(4)3-, SO4(2-), SO(3)2-, NO3- or 30 mg/L of Pb(II), Zn(II), Cd(II) ions. However, heat treatment caused significant dropped in Cr(VI) reduction to less than 20% only. A. haemolyticus cells loses its shape and size after exposure to 10 and 50 mg Cr(VI)/L as revealed from TEM examination. The presence of electron-dense particles in the cytoplasmic region of the bacteria suggested deposition of chromium in the cells.     

Taguchi optimization approach for the polypropylene fiber reinforced concrete strengthening with polymer after high temperature

In this study, the strengthening with polymer the polypropylene fiber reinforced concrete exposed to high temperature was examined. Taguchi L₉ (3³) orthogonal array was used for the design of experiments. Three different parameters were used in the study; polypropylene fiber percentage (0 %, 1 % and 2 %), high temperature degree (300 °C, 600 °C and 900 °C) and curing period (3, 7 and 28 days). Cube samples of 100x100x100 mm sizes were produced for the compressive strength and ultrasonic pulse velocity tests. The samples were removed from the water and dried at 105?±?5 °C, and then they were exposed to temperatures of 300 °C, 600 °C and 900 °C. Then, the polymerization of monomer and the vinyl acetate monomer impregnation on the samples were carried out. The compressive strength and ultrasonic pulse velocity tests were made. Taguchi analysis showed that the largest compressive strength and ultrasonic pulse velocity were obtained at a rate of 0 % from the samples with polypropylene fiber exposed to 600 °C and kept for 28 days as cure period. It was determined as the result of Anova analysis that high temperature had made biggest effect on the compressive strength and ultrasonic pulse velocity of the concrete reinforced with polymer.     

Synthesis of mesoporous titania nanoparticles with anatase frameworks and investigation of their photocatalytic performance

In this research paper, we synthesize various types of mesoporous titania nanoparticles (MTNs) with suitable surface area and pore size while creating anatase frameworks by applying hydrothermal treatment or calcination at different temperatures. Wide-angle XRD patterns and N2 adsorption-desorption isotherms reveal that the MTNs with crystallized anatase frameworks can be synthesized after an optimized hydrothermal treatment. In contrast, calcination of MTNs at high temperature caused the collapse of mesoporous structure, resulted in drastic reduction of the surface area of the MTNs. In addition, we investigate the photocatalytic activity of the prepared MTNs by measuring the degradation of methylene blue (MB). The results show that the reaction rates of the photocatalytic MB decomposition strongly depend on the degree of crystallinity in the MTNs frameworks and on the surface area of MTNs.     

Case Study: Flood Mitigation of the Muda River, Malaysia

The 2003 flood of the Muda River reached 1,340?m3/s at Ladang Victoria and adversely impacted 45,000 people in Malaysia. A flood control remediation plan proposed a levee height based on a 50-year discharge of 1,815?m3/s obtained from hydrologic models. This design discharge falls outside the 95% confidence intervals of the flood frequency analysis based on field measurements. Instream sand and gravel mining operations also caused excessive riverbed degradation, which largely off sets apparent benefits for flood control. Pumping stations have been systematically required at irrigation canal intakes. Several bridge piers have also been severely undermined and emergency abutment protection works were needed in several places. Instream sand and gravel mining activities should be replaced with offstream mining in the future.     

Prediction of sand mass and organic matter distribution via in situ measured wet sediment bulk density profile

The objective of the study is to develop a spatial prediction model of sand mass and organic matter distribution in an urban stormwater holding pond using in situ measured wet sediment bulk density profile data to spatially distinguish the most likely contaminated sediment deposit areas. The wet bulk density profiles of deposited sediment at 25 locations in the Berembang (Malaysia) stormwater holding pond were measured using a single-probe nuclear density gauge. The sand and organic matter compositions of the surface sediment sample, 5 cm thickness from the bed surface, were determined. Discriminant analysis (DA) was conducted to generate two Fisher’s linear discriminant functions for the prediction of sand mass and organic matter composition areas, respectively. The linear discriminant functions generated better area classifications of surface organic matter composition compared to the sand mass distribution using wet sediment bulk density data measured at more than 15 cm depth levels.     

Microstructure and High Temperature Impression Creep Properties of Mg–3Ca–xZr (x = 0.3, 0.6, 0.9 wt%) Alloys

The current study has investigated the influence of zirconium (Zr) addition to Mg–3Ca–xZr (x = 0.3, 0.6, 0.9 wt%) alloys prepared using argon arc melting on the microstructure and impression properties at 448–498 K under constant stress of 380 MPa. Microstructural analysis of as-cast Mg–3Ca–xZr alloys showed grain refinement with Zr addition. The observed grain refinement was attributed to the growth restriction effect of Zr in hypoperitectic Mg–3Ca–0.3 wt% Zr alloys. Heterogeneous nucleation of α-Mg in properitectic Zr during solidification resulted in grain refinement of hyperperitectic Mg–3Ca–0.6 wt% Zr and Mg–3Ca–0.9 wt% Zr alloys. The hardness of Mg–3Ca–xZr alloys increased as the amount of Zr increased due to grain refinement and solid solution strengthening of α-Mg by Zr. Creep resistance of Mg–3Ca–xZr alloys increased with the addition of Zr due to solid solution strengthening of α-Mg by Zr. The calculated activation energy (Q_a) for Mg–3Ca samples (131.49 kJ/mol) was the highest among all alloy compositions. The Q_a values for 0.3, 0.6 and 0.9 wt% Zr containing Mg–3Ca alloys were 107.22, 118.18 and 115.24 kJ/mol, respectively.     

Denitrogenation of carbazole by a novel strain Bacillus Clausii BS1 isolated from Egyptian Coke

In this study, an effective enrichment technique was applied to isolate different bacterial strains with capabilities to denitrogenate carbazole (CAR), as a model compound for nitrogenous polyaromatic hydrocarbons (NPAHs). Twenty-four different CAR-denitrogenating bacterial strains were isolated from mineral coke samples. From all, a Gram +ve bacterial isolate designated BS1 showed a higher biodenitrogenation (BDN) efficiency relevant to the well-known biodenitrogenating bacterium strain Pseudomonas resinovorans CA10, recording 77.15 and 60.66% removal of 1000 ppm CAR with the production of 119.79 and 102.43 ppm anthranilic acid, and 121.19 and 90.33 ppm catechol, as by-products, respectively. BS1 was identified by 16S rDNA gene sequence analysis to be Bacillus clausii BS1 (NCBI GenBank Accession no. KF985981) with a similarity of 99.14%. The CAR-BDN pathway was also elucidated using high-performance liquid chromatography (HPLC) and gas chromatography mass spectrometry analysis (GC/MS), which proved further metabolism of catechol to muconic acid.     

Effects of Growth Rates and Compositions on Dendrite Arm Spacings in Directionally Solidified Al-Zn Alloys

Dendritic spacing can affect microsegregation profiles and also the formation of secondary phases within interdendritic regions, which influences the mechanical properties of cast structures. To understand dendritic spacings, it is important to understand the effects of growth rate and composition on primary dendrite arm spacing (λ ₁) and secondary dendrite arm spacing (λ ₂). In this study, aluminum alloys with concentrations of (1, 3, and 5 wt pct) Zn were directionally solidified upwards using a Bridgman-type directional solidification apparatus under a constant temperature gradient (10.3 K/mm), resulting in a wide range of growth rates (8.3–165.0 μm/s). Microstructural parameters, λ ₁ and λ ₂ were measured and expressed as functions of growth rate and composition using a linear regression analysis method. The values of λ ₁ and λ ₂ decreased with increasing growth rates. However, the values of λ ₁ increased with increasing concentration of Zn in the Al-Zn alloy, but the values of λ ₂ decreased systematically with an increased Zn concentration. In addition, a transition from a cellular to a dendritic structure was observed at a relatively low growth rate (16.5 μm/s) in this study of binary alloys. The experimental results were compared with predictive theoretical models as well as experimental works for dendritic spacing.