Comparative study of the elimination of toluene vapours in twin biotrickling filters using two microorganisms Bacillus cereus S1 and S2

BACKGROUND: To investigate the microbial degradation performance of organic pollutants in the atmosphere using a biotrickling filter, two microorganism strains, Bacillus cereus S1 and Bacillus cereus S2, were selected, identified and inoculated into a twin biotrickling filter for comparison. RESULTS: Both strains showed good performance towards the degradation of model organic pollutants when gas flow rates ranged from 100 to 600 L h⁻¹. For S1, the total maximum removal efficiency (RE) of toluene was maintained nearly 100% not only at gas flow rates of 100 L h⁻¹ corresponding to empty bed residence time (EBRT) 199.44 s, but also at gas flow rates of 200 L h⁻¹ (EBRT = 99.72 s) and 300 L h⁻¹ (EBRT = 66.48 s). However, S2 had a much lower degradation capability; near 100% removal efficiency was obtained only at the gas flow rate of 100 L h⁻¹ although both bacteria belong to the same Bacillus cereus. With further increase in gas flow rate, the total REs for both S1 and S2 decreased slightly at first and then dropped sharply to 46% and 35%, respectively, at an EBRT of 33.24 s, corresponding to a gas flow rate of 600 L h⁻¹. Starvation for between 2 and 10 days resulted in the re‐acclimation times of both strains ranging between 1.0 and 15.5 h. CONCLUSION: Strain S1 would be a better choice for inoculation into a biotrickling filter than strain S2, because of its much higher toluene removal capacity and rapid recovery to full performance. Copyright © 2008 Society of Chemical Industry     

Organic‐acid‐catalyzed sol–gel route for preparing poly(methyl methacrylate)–silica hybrid materials

In this study, a series of organic–inorganic hybrid sol–gel materials consisting of a poly(methyl methacrylate) (PMMA) matrix and dispersed silica (SiO₂) particles were successfully prepared through an organic‐acid‐catalyzed sol–gel route with N‐methyl‐2‐pyrrolidone as the mixing solvent. The as‐synthesized PMMA–SiO₂ nanocomposites were subsequently characterized with Fourier transform infrared spectroscopy and transmission electron microscopy. The solid phase of organic camphor sulfonic acid was employed to catalyze the hydrolysis and condensation (i.e., sol–gel reactions) of tetraethyl orthosilicate in the PMMA matrix. The formation of the hybrid membranes was beneficial for the physical properties at low SiO₂ loadings, especially for enhanced mechanical strength and gas barrier properties, in comparison with the neat PMMA. The effects of material composition on the thermal stability, thermal conductivity, mechanical strength, molecular permeability, optical clarity, and surface morphology of the as‐prepared hybrid PMMA–SiO₂ nanocomposites in the form of membranes were investigated with thermogravimetric analysis, differential scanning calorimetry, dynamic mechanical analysis, gas permeability analysis, ultraviolet–visible transmission spectroscopy, and atomic force microscopy, respectively. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Synthesis and characterization of novel copolymer containing pyridylazo-2-naphthoxyl group via reversible addition–fragmentation chain transfer (RAFT) polymerization

A novel monomer containing pyridylazo-2-naphthoxyl group, 1-(1-(4-vinylbenzyloxy)naphthalen-2-yl)-2-(pyridin-2-yl)diazene (VBNPA), was successfully synthesized and copolymerized with styrene (St) in N,N-dimethyl formamide (DMF) via reversible addition–fragmentation chain transfer (RAFT) polymerization using 2-cyanoprop-2-yl-1-dithionaphthalate (CPDN) as RAFT agent. The polymerization behavior exhibited “living”/controlled characters. The obtained copolymer, poly(St-co-VBNPA), with pre-determinable molecular weight and narrow molecular weight distribution can be used as a carrier in metal ion detection and analysis via pre-concentration technique. The copolymer–metal ion (copper (Cu) and europium (Eu)) complexes were prepared and characterized.     

Enhanced Topology Error Processing via Optimal Measurement Design

Topology errors constitute one of the significant source of problems for today's state estimators. They may cause significant biases in state estimation solutions and may occasionally lead to divergence of the numerical solution algorithms. Existing methods of detecting and identifying topology errors rely on the measurement residuals which are in turn dependent on the measurement configuration and network topology. Hence, the capability to effectively process topology errors is closely linked to proper measurement design. In particular, detection of a topology error associated with a given branch may or may not be possible depending upon the existing measurement configuration. Hence, it is possible to efficiently improve the topology error processing capability for a given system by strategically placing few extra measurements. In this paper, a systematic procedure will be developed in order to accomplish this by using not only the traditional power flow and injection measurements but also the newly emerging phasor measurement units (PMUs). Numerical examples will be provided in order to illustrate the proposed measurement placement strategy.      

一种矿山用钢筋网自动化焊接生产线的设计

设计一条钢筋网自动化焊接生产线，包括经料送料平台、纬料自动分料及上料机构、多点电阻点焊机、接料平台、卸料机械手。从上料到出料依靠电机、汽缸之间的协调工作来实现。并由单片机和PLC实现控制功能，上位机用MCGS组态软件在整个过程监视现场，采集工作状态及参数，起到监控作用。     

Evaluation of Soybean Seedcoat Cracking During Drying:PART II. Using MRI

MRI techniques were developed and employed for non-destructive and noninvasive study of seedcoat cracking in low moisture soybean kernels during heated air drying. Proton density image and transient moisture distribution profile of a single soybean kernel can be obtained using MRI. These MRI techniques proved to be particularly useful for the continuous observation of initiation and propagation of seedcoat cracking during the entire period of drying process without interruption.

The proton density images of soybean kernels showed that seedcoat cracking was initiated perpendicular to the long axis of the kernel near the hilum. The transient moisture distribution profiles in soybean kernels during drying indicate that moisture gradient developed during drying was higher in the seedcoat than in the cotyledon. Drying temperature and initial average moisture content were positively correlated with the soyhean seedcoat crackig. The location of the     

Surgical treatment of unilateral alveolar cleft

In this study, 16 cases of unilateral alveolar cleft with cleft lip and palate were repaired with autografts of cancellous bone (13 cases) or hydroxyapatite (3 cases). The grafts were covered by reflected mucoperiosteal flaps and a mucosal flap from the upper lip. Twelve of the thirteen cases were followed up for 1-5 years. Nine of whom using cancellous bone had bony continuity of the maxilla and 7 cases erupted permanent maxillary canines within the area of autografts. None of the 3 cases using hydroxyapatite erupted a canine tooth. The results showed that autograft was better than hydroxyapatite in terms of maxillary canine eruption.     

Nonlinear distortion prediction of active filters

The represention of circuit variables in frequency-domain complex matrix and nonlinearities by power series gives rise to a nonlinear distortion prediction technique, the intermodulation-balance method. This operates entirely in the frequency domain. The technique is verified by a single-amplifier filter with a two-tone input signal