核桃雄花中总多酚提取工艺的研究

采用单因素和正交试验研究核桃雄花中多酚类物质的最佳提取工艺条件。通过对4种不同溶剂(无水乙醇、甲醇、丙酮和乙酸乙酯)在相同试验条件下的浸提效果比较发现,甲醇是核桃雄花中总酚类物质的最佳提取试剂。然后分别采用常规水浴浸提法和超声波辅助浸提法对甲醇体分数、浸提温度、浸提时间和料液比等因素进行研究,在确定最佳单因素水平的基础上,再利用正交试验优化以甲醇为浸提剂的提取工艺条件,试验得出超声波辅助浸提法具有用时短、总多酚提取量高的优点,其最佳工艺条件为:料液比1∶30(g/m L)、甲醇溶液体积分数30%、温度70℃、浸提时间10 min。在此条件下,核桃雄花中的总多酚含量可达6.56%,明显高于其他条件下的。     

Removal of imidacloprid and acetamiprid from tea infusions by microfiltration membrane

Removal of imidacloprid and acetamiprid in tea infusions by microfiltration membrane using dead‐end model was investigated in the present study. The results showed that microfiltration significantly promoted the removal of both pesticides (P < 0.05) in tea infusions. Furthermore, the extent of removal was strongly influenced by the pore size of membrane, operational pressure and the concentrations of tea infusions. The initial concentration of imidacloprid and acetamiprid showed no significant effect on their removal rates. The maximum removal rates were 79.7% for imidacloprid and 81.9% acetamiprid. The changes in major chemical components of tea infusions after microfiltration were evaluated. The results indicated that microfiltration caused no considerable changes in total polyphenols and total free amino acids, and small but statistically significant losses (6.3–18.0%) of eight catechins and three methylxanthines when filtration volume reached to 200 mL. The present study validated the application of microfiltration as a potentially feasible and promising method for the removal of imidacloprid and acetamiprid residues from tea infusions.     

Landau-Zener模型中纠缠演化及转移的研究

研究了受外场驱动的两个二能级系统分别与两个单模量子化光场相互作用模型中纠缠演化及转移问题。该工作主要是对外场驱动的Landau-Zener模型进行了研究，采用旋转波近似的方法，通过数值计算详细分析了二能级系统初始状态、能级间的耦合常数以及驱动外场的参数对子系统间纠缠和转移特性的影响。结果表明，适当调节模型中的参数，可以使系统初始纠缠完全转移为光腔场间的纠缠，实现二能级系统与光场间的最大纠缠转移。     

Recent progress of the gas diffusion layer in proton exchange membrane fuel cells: Material and structure designs of microporous layer

Proton exchange membrane fuel cells (PEMFCs) have become the most attractive power supply units for stationary and mobile applications. The operation, design characteristics, as well as performance of PEMFCs, are closely related to the multiphase transport of mass, heat, and electricity in the cell, a critical of which is the gas diffusion layer (GDL). It is very important to guarantee the transmission of water and gasses under high current density, and which is the weakness of PEMFCs at present. Microporous layer (MPL) is considered to be the key variable for mass transfer, so varieties of works focus on modification of MPL materials and its structure design. However, there is still a lack of special review to summarize and prospect the progress of MPL in recent years. This review article therefore focuses on the insights and comprehensive understanding of four critical issues of the MPL, the porosity, pore size distribution, wettability, structural design and the durability of MPL. At last, the conclusion and recommendations section summarized the future prospects and recommendations for possible research opportunities.     

Control of the particle microstructure during the synthesis of bulk-polymerized transparent methacrylate-acrylonitrile-butadiene-styrene resin

A series of methacrylate-acrylonitrile-butadiene-styrene (MABS) resins was prepared using bulk polymerization. The polarity of the continuous phase and the compatibility of two phases were changed by adjusting the methyl methacrylate (MMA) content, choosing values that were close to styrene-butadiene rubber solubility value. The possibility of controlling the microstructure of the MABS resin by changing the polarity of the components and the compatibility of two phases was assessed. The dynamic mechanical analysis shows that the compatibility of two phases varies with the MMA content. The morphological analysis shows that increasing MMA contents results in a gradual decrease in the sub-inclusion structure with a network skeleton of rubber particles, and that all the particles become solid rubber when the MMA content reaches 75%. The sub-inclusion structure reappears but does not have a network skeleton when the MMA content is 90%. The impact strength and morphological analysis indicate that the solid rubber particles and the sub-inclusion structure with a network skeleton provide excellent toughness, while the sub-inclusion structure without a network skeleton does not. In contrast, the transmittance of the ABS resin first increased and then decreased with increasing MMA content.     

A Student's t-based density peaks clustering with superpixel segmentation (tDPCSS) method for image color clustering

Image color clustering is a basic technique in image processing and computer vision, which is often applied in image segmentation, color transfer, contrast enhancement, object detection, skin color capture, and so forth. Various clustering algorithms have been employed for image color clustering in recent years. However, most of the algorithms require a large amount of memory or a predetermined number of clusters. In addition, some of the existing algorithms are sensitive to the parameter configurations. In order to tackle the above problems, we propose an image color clustering method named Student's t-based density peaks clustering with superpixel segmentation (tDPCSS), which can automatically obtain clustering results, without requiring a large amount of memory, and is not dependent on the parameters of the algorithm or the number of clusters. In tDPCSS, superpixels are obtained based on automatic and constrained simple non-iterative clustering, to automatically decrease the image data volume. A Student's t kernel function and a cluster center selection method are adopted to eliminate the dependence of the density peak clustering on parameters and the number of clusters, respectively. The experiments undertaken in this study confirmed that the proposed approach outperforms k-means, fuzzy c-means, mean-shift clustering, and density peak clustering with superpixel segmentation in the accuracy of the cluster centers and the validity of the clustering results.