最大熵在感应测井反演中的应用

常规的反演方法是对感应测井资料进行线性反褶积。由于感应测并获得的响应曲线是地层非线性时变滤波的结果,感应测井响应随地层电导率发生非线性变化。本文把熵的概念引入到感应测井反演中。用最大熵方法分别设计出实部信号和虚部信号所对应的反滤波因子,两条反映测井响应随电导率非线性变化的非线性函数也被拟合出来。文章最后用设计出的滤波因子及被拟合出的非线性函数对模拟相量感应测井资料进行了相量反褶积。处理结果表明,围岩效应和趋肤效应基本被消除。本方法与常规的三点反褶积法相比,克服了过聚焦现象,提高了精度。     

DNA/lipid complex organogel with shape‐memory behavior

DNA and amphiphilic N,N,N‐trimethyl‐N‐hexadecylammonium bromide (THAB) were stoichiometrically mixed together to produce a DNA–lipid complex, which was dissolved in dimethyl sulfoxide (DMSO) at 65°C and then crosslinked with isophorone diisocyanate (IPDI). The obtained organogel swelled reversibly in DMSO, responding to the variation of temperature. Interestingly, we observed that the gel exhibited a temperature‐dependent shape‐memory behavior. Above 65°C, whatever the shape the gel was deformed to, it could retain the new shape as the temperature was decreased to room temperature, while, when the gel was heated to 65°C again, it could recover its initial shape. The shape‐memory characteristic is supposedly originated from the transition between the close‐packed and the destroyed DNA/lipid conformation. The elastic urethane crosslinking bonds between base‐pair sites act as a fixing phase. The gel holds promise in its application as a gentle actuator. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 259–263, 2002     

Manufacture of carbon fibers from polyacrylonitrile precursors treated with CoSO4

Free‐radical solution copolymerization of itaconic acid and acrylonitrile was carried out in DMSO using azodiisobutyronitrile as an initiator, changing the feed rate of itaconic acid. The resulting polymerization solution was spun to form polyacrylonitrile (PAN) precursors of carbon fibers. The precursors were treated with a CoSO₄ aqueous solution on‐line. The structure and properties of untreated and treated PAN precursors and the resultant carbon fibers were characterized by SEM and TEM, a stabilization process, etc. It is suggested that CoSO₄ acts as a catalyst in the formation of a ladder structure and reduces the temperature of cyclization, and the carbon fibers developed from treated PAN fibers showed improvement in the tensile strength and the Young's modulus. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 85: 153–158, 2002     

Modeling of the bulk free radical polymerization up to high conversion—three stage polymerization model. II. Number-average molecular weight and apparent initiator efficiency

The equations for predicting the number-average molecular weight are derived on the basis of the three stage polymerization model (TSPM) in this paper. By applying the equations, a plotting approach is proposed to determine the apparent initiator efficiency defined as f[(α_td+1)/2] and the constant of chain transfer to monomer, where f is the initiator efficiency and α_td denotes the fraction of the termination rate constants by disproportionation. Using the approach to plot the experimental data in the literature, it is found that the chain transfer to monomer can be neglected for both methylmethacrylate (MMA) and styrene (St) polymerizations, but it can exert a significant effect on ethylmethacrylate (EMA) polymerization. In addition, the apparent initiator efficiency is found to be independent of reaction temperature and initiator concentration at each stage. The values of f[(α_td+1)/2] at gel effect stage are slightly reduced as compared with that at low conversion stage for MMA and EMA polymerizations. However, it decreases significantly at gel effect stage for St polymerization. Using the equations derived and the apparent initiator efficiencies obtained from TSPM plots, the number-average molecular weights at different conversions can be predicted. Comparisons show that the agreement between predictions and experimental data is satisfactory.     

长脉冲激光沉积原位生成YBaCuO超导膜

用长脉冲激光(脉冲宽度150μs,波长1.06μm)辐照高温烧结的YBa_2Cu_3O_(7-x)靶,在6Pa的氧气压强下,巳在(100)YSZ单晶衬底上原位生成YBa_2Cu_(?)O_(7-x)超导膜。衬底置于750℃的加热器上,衬底与靶之间的距离5cm,用该法制得的薄膜光亮坚实,正常态呈金属性,零电阻温度为84.7K。用XRD和SEM对薄膜进行了分析研究。     

圆钢锭浇铸工艺试验

在不同锭型钢中A1含量及S含量、浇铸温度及浇铸时间等试验工艺条件下,对模铸20管钢、φ450mm、2.1t(圆波浪形)钢锭裂纹率的影响进行了分析与讨论,并确定了主要工艺参数。     

密码子优化的牛精蛋白基因在大肠杆菌中的表达

以PCR的方法得到牛精蛋白基因的基因，去其内含子，得到牛精蛋白cDNA，克隆入原核表达载体pGEX-2T中，组装成表达载体pGEX-2T-PE，利用大肠杆菌偏好的编码精氨酸的密码子CGT将野生型牛精蛋白基因中编码精氨酸的稀有密码子（AGA或AGG）替换掉，通过基因合成得到密码子优化的牛精蛋白的基因，将其克隆入原核表达载体pGEX-2T中，组装成表达载体pGEX-2T-PS。将这两个表达载体分别转化入大肠杆菌表达菌株BL21中，经IPTG诱导，同样条件下，野生型牛精蛋白基因无法得到表达，密码子优化的牛精蛋白基因能够得到良好的表达，表达产物约占细菌总蛋白的18％，将表达蛋白纯化，进行DNA－蛋白结合实验，发现其能与DNA发生非特异性的结合。     

Stable redesign of predictive control

The paper deals with I/O versions of receding horizon controllers based on the minimization of multistep quadratic costs with the constraint that the terminal state goes to zero. The resulting control law yields stable closed-loop systems under sharp conditions. Simulation results are presented to both verify the theoretical analysis and relate the new control law with GPC     

Synthesis and Spectral Properties of Mixed-Ligand Complexes of Lanthanide Perchlorate with Bis-(phenylsulfinyl)ethane and Organic Lewis Bases

ＳｙｎｔｈｅｓｉｓａｎｄＳｐｅｃｔｒａｌＰｒｏｐｅｒｔｉｅｓｏｆＭｉｘｅｄＬｉｇａｎｄＣｏｍｐｌｅｘｅｓｏｆＬａｎｔｈａｎｉｄｅＰｅｒｃｈｌｏｒａｔｅｗｉｔｈＢｉｓ（ｐｈｅｎｙｌｓｕｌｆｉｎｙｌ）ｅｔｈａｎｅａｎｄＯｒｇａｎｉｃＬｅｗｉｓＢａｓｅ...