锆基块体非晶合金的力学性能研究进展

本文叙述了锆基块体非晶合金的制备方法，优异的性能，特别是对其力学性能研究领域的最新进展进行了综述。并与传统晶态合金作了适当的对比，锆基块体非晶合金具有优异的力学性能，如弹性比功、超塑性、断裂韧性等，此类合金的应用将不断拓宽。     

导叶叶片数对多相混输泵内能量损失的影响北大核心

为了提高混输泵的做功性能,降低能量损失,在不同导叶叶片数下,对多相混输泵的外特性及其内部能量损失进行分析。结果表明:当导叶叶片数为10时混输泵的外特性明显比导叶叶片数为7和8时更差,且最高效率偏向小流量工况;不同流量下,导叶叶片数为8时混输泵叶轮内的收缩损失和湍流耗散损失最小,而导叶叶片数对导叶进口的冲击损失影响很小,可不考虑其影响;在所选3组导叶叶片数下,当导叶叶片数等于8时混输泵的性能最优且流道内能量损失最小。     

含Li的Al-Zn-Mg-Cu合金沉淀析出过程的定量分析

应用小角度X射线散射技术结合TEM分析定量的描述Al-Zn-Mg-Cu-Li合金时效过程中析出相尺寸分布和形貌等信息。通过分析确定合金在几种时效状态下析出相为轴比在0．2～0．4之间的扁回转椭球形。确定了析出相特征尺寸的对数正态分布和质量依回转半径的Maxwell分布。并分析分布曲线随动力强度Ks的变化特征，可以看出，析出相尺寸和质量分布曲线基本满足随动力强度增加，几何平均值增加，分布范围变宽。     

低翘曲玻纤增强PET复合材料的制备和性能研究

依据降低翘曲的机理，选用不同降低翘曲的方法，制备了系列翘曲玻纤增强PET复合材料，结果表明，具有较高形状对称性的填料，如滑石粉，云母粉和玻璃微珠都能不同程度地降低玻纤增强PET体系的翘曲，非晶聚合物也能有效改进该体系的翘曲性能。     

水利工程施工应急能力G1-灰色评价方法研究

为有效加强水利工程应急能力建设,采用G1-灰色综合评价法对水利工程应急能力进行了综合评价研究。在水利工程施工特点和应急管理研究基础上,建立应急能力评价指标体系。通过采用G1法分析各应急能力评价指标相互关系,确定了指标权重。引入灰色理论将样本信息处理成灰色评价矩阵,并结合指标权重进行单值化处理得到应急能力综合评价值和评价等级。研究结果表明,搜救抢险能力、应急资源调配能力和应急决策指挥能力对于水利工程应急能力建设起到最主要的作用。该评价方法不仅可揭示指标重要程度关系,还能有效量化和评价水利工程项目综合应急水平,具有较好的实用性。     

Synthesis and Characterization of Highly Dispersed Antimony-Doped Stannic Hydroxide Nanoparticles: Effects of the Azeotropic Solvents to Remove Water on the Properties and Microstructures of the Nanoparticles

Highly dispersed antimony (Sb)-doped stannic hydroxide nanoparticles have been successfully prepared using the solution chemistry method. The properties and microstructures of the nanoparticles are investigated in detail by means of infrared, transmission electron microscope, X-ray diffractometer, and Brunauer-Emmett-Teller nitrogen surface area measurements. The results indicate that the properties and microstructures of the nanoparticles strongly depend on the azeotropic solvents used to remove water at the drying stage. Various azeotropic solvents are screened to investigate their effects on the size and dispersivity of dried Sb-doped stannic hydroxide. Three empirical rules are drawn for selecting an effective azeotropic solvent: (1) the solvent molecule should contain at least one atom such as oxygen as the hydrogen (H)-bond acceptor to form H bonds with the surface –OH (acting as an H-bond donor) of polymer particle; (2) the H-bond acceptor should locate in the middle of the alkane chain rather than on the terminal so that the alkane chain can stretch out and cover more surface area, improving the dispersivity of the dried product; and (3) the solvent should have a higher boiling point (∼140°C) to reduce the time of azeotropic distillation for removing water and maintain a lower residual amount of azeotropic agent. Based on the empirical rules, it is discovered that iso-amyl acetate is the most effective azeotropic solvent.     

界面改性剂对PP/滑石粉形态结构和性能影响

用在50L固相接枝反应器中合成的等规聚丙烯接枝马来酸酐(PP-g—MAH)作界面改性剂，制备了PP—g—MAH／PP／滑石粉复合材料。研究了PP—g—MAH／PP／滑石粉复合材料的形态结构和力学性能。结果表明，PP—g—MAH对PP／滑石粉复合物的缺口冲击强度、弯曲强度和拉伸强度均有增强作用；PP—g—MAH对PP／滑石粉复合物表观粘度几乎没有影响。SEM观察发现PP—g—MAH对PP／滑石粉复合物相界面有明显的改善。     

碱金属和锌对高炉用SiAlON结合刚玉砖的复合侵蚀

将高炉用SiAlON结合刚玉砖制成外部尺寸为50mm×50mm,内孔尺寸为25mm×25mm的坩埚,分别加入由Na2CO3、K2CO3、ZnO和宝钢高炉现场高炉灰配制的炉渣(其w(Na2O+K2O)=2.75%,w(ZnO)=5.1%)和用K2CO3、ZnO、石墨配制的炉渣(其w(Na2O+K2O)=25%,w(ZnO)=25%),然后分别在还原气氛下于1350℃16h和1100℃40h进行侵蚀试验。将侵蚀后的试样纵向对称剖开,观察渣对试样的侵蚀和渗透情况,进行SEM和EDAX分析。结果表明:碱金属和锌含量不同的两种炉渣对SiAlON结合刚玉砖的侵蚀速度都很小;碱金属侵蚀机理主要是SiAlON与碱蒸气反应生成钾霞石,与渣反应生成铁橄榄石,并参与硅酸盐玻璃相的生成;刚玉颗粒与渣中的FeO、Na2O和K2O反应生成铁铝尖晶石和少量针状β-Al2O3;锌对该砖没有产生明显的化学侵蚀。     

优化煤气炉工艺实现增产降耗

山西晋城煤化工有限责任公司一期项目———合成氨-尿素“18·30”装置2004年开始试车,至2005年10月底,共生产合成氨164 058·52 t,尿素280 422·8 t,产品合格率达到了98%。该装置的9台Φ3·6 m煤气发生炉原料主要来自晋城市辖区的11个煤矿,投运后随着生产工艺的逐步优化,原料煤耗逐月下降,现合成氨吨氨煤耗可控制在1 420 kg以下。本文以山西晋城煤化工有限责任公司实际生产情况为例,探讨如何通过优化控制来实现造气系统的增产、降耗。1Φ3·6 m煤气发生炉工艺简介吹风气及烟气流程空气风机→煤气炉→旋风除尘器→安全除尘U型水封→燃烧炉…     

An Efficient Semi-Analytical Simulation for the Heston Model

With splitting technique, a new semi-analytical scheme with predictable strong convergence order 1.0 is proposed for the transformed Heston model, where the variance process is displaced by the corresponding volatility process. The volatility process is decomposed into a linear SDE and an ODE, both of which have the analytical solution, but the SDE is simulated by the Euler method while the ODE is approximated analytically with a slight modification. Numerical tests show its high efficiency and accuracy in the simulation for the mean-reverting square root process.