State of polarization changes: Classification and measurement

We propose a standardization procedure that provides a convenient, quantitative and reproducible laboratory-based method for measuring the state of polarization (SOP) fluctuations produced by polarization varying devices. This method is based on the SOP distributions generated by commercial polarization scramblers. We show that these devices generate distributions of the maximum change of the SOP (in a given sample time) that follow Rayleigh statistics, which scale linearly with scrambling frequency and the sample time. We use this procedure to measure the SOP fluctuations in a short length of coiled fiber subject to mechanical perturbations.     

A Digital Deformation Vacuum Gauge with an LC-Generator

The design of a sylphon bellows sensor and the basic circuits of an LC-generator and of a microprocessor unit are presented. An analytical pressure–frequency conversion function and a special method of adjusting the sensor ensure an error of less than 0.05%. The dynamic range is up to 10⁵. The instruments developed cover the ranges 10³, 10⁴, and 10⁵ Pa.     

Randomized scheduling algorithms for high-aggregate bandwidth switches

The aggregate bandwidth of a switch is its port count multiplied by its operating line rate. We consider switches with high-aggregate bandwidths; for example, a 30-port switch operating at 40 Gb/s or a 1000-port switch operating at 1 Gb/s. Designing high-performance schedulers for such switches with input queues is a challenging problem for the following reasons: (1) high performance requires finding good matchings; (2) good matchings take time to find; and (3) in high-aggregate bandwidth switches there is either too little time (due to high line rates) or there is too much work to do (due to a high port count). We exploit the following features of the switching problem to devise simple-to-implement, high-performance schedulers for high-aggregate bandwidth switches: (1) the state of the switch (carried in the lengths of its queues) changes slowly with time, implying that heavy matchings will likely stay heavy over a period of time and (2) observing arriving packets will convey useful information about the state of the switch. The above features are exploited using hardware parallelism and randomization to yield three scheduling algorithms - APSARA, LAURA, and SERENA. These algorithms are shown to achieve 100% throughput and simulations show that their delay performance is quite close to that of the maximum weight matching, even when the traffic is correlated. We also consider the stability property of these algorithms under generic admissible traffic using the fluid-model technique. The main contribution of this paper is a suite of simple to implement, high-performance scheduling algorithms for input-queued switches. We exploit a novel operation, called MERGE, which combines the edges of two matchings to produce a heavier match, and study of the properties of this operation via simulations and theory. The stability proof of the randomized algorithms we present involves a derandomization procedure and uses methods which may have wider applicability.     

Untersuchung der Verteilung und Intensität filamentierter Barrierenplasmen für die Behandlung von Oberflächen

The application of barrier discharges at atmospheric pressure in air expands on the market of plasma technology, because it is an ecological and cost‐effective alternative to other processes of surface treatment. These plasmas usually consist of a multitude of spatially and temporally localized filaments, whose distribution should be as even as possible for homogeneous treatment. This holds especially for the plasma treatment of sensitive goods such as wool or other textiles. In equipment for continuous pass of material the barrier arrangements often consist of a system cylinder – cylinder or cylinder – plane, whereby the gap width changes locally. Space distribution and intensity of filaments has been investigated by means of short‐time photography and spatially resolved measurement of current distribution and energy distribution derived from it. The local dependency found can be explained by means of a capacitive equivalent circuit.     

Oxidative degradation of polyamide reverse osmosis membranes: Studies of molecular model compounds and selected membranes

Selected aromatic amides were used to model the chemical reactivity of aromatic polyamides found in thin‐film composite reverse osmosis (RO) membranes. Chlorination and possible amide bond cleavage of aromatic amides upon exposure to aqueous chlorine, which can lead to membrane failure, were investigated. Correlations are made of the available chlorine concentration, pH, and exposure time with chemical changes in the model compounds. From the observed reactivity trends, insights are obtained into the mechanism of RO membrane performance loss upon chlorine exposure. Two chemical pathways for degradation are shown, one at constant pH and another that is pH‐history dependent. An alternative strategy is presented for the design of chlorine‐resistant RO membranes, and an initial performance study of RO membranes incorporating this strategy is reported. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 1173–1184, 2003     

Effect of film thickness on hydrogen content in a-Si : H

The hydrogen content, its depth distribution, and its bonding configuration have been studied in hydrogenated amorphous silicon prepared by plasma-enhanced chemical vapor deposition with hydrogen-diluted silane. Nuclear reaction analysis and infrared spectroscopy were used to determine the total amount of hydrogen and its bonded component, respectively. It has been established that the total concentration of hydrogen does not depend on the film thickness, and has a uniform depth profile. The concentration of bonded hydrogen changes with the film thickness within the measurement accuracy. The data obtained suggest the presence of molecular (non-bonded) hydrogen, uniformly distributed in concentration across the film thickness.     

Lateral ion implant straggle and mask proximity effect

Lateral scattering of retrograde well implants is shown to have an effect on the threshold voltage of nearby devices. The threshold voltage of both NMOSFETs and PMOSFETs increases in magnitude for conventional retrograde wells, but for triple-well isolated NMOSFETs the threshold voltage decreases for narrow devices near the edge of the well. Electrical data, SIMS, and SUPREM4 simulations are shown that elucidate the phenomenon.     

Design of 5.9 ghz dsrc-based vehicular safety communication

The automotive industry is moving aggressively in the direction of advanced active safety. Dedicated short-range communication (DSRC) is a key enabling technology for the next generation of communication-based safety applications. One aspect of vehicular safety communication is the routine broadcast of messages among all equipped vehicles. Therefore, channel congestion control and broadcast performance improvement are of particular concern and need to be addressed in the overall protocol design. Furthermore, the explicit multichannel nature of DSRC necessitates a concurrent multichannel operational scheme for safety and non-safety applications. This article provides an overview of DSRC based vehicular safety communications and proposes a coherent set of protocols to address these requirements     

A New Hand-Held Microsystem Architecture for Biological Analysis

This paper presents a hand-held microsystem based on new fully integrated magnetoresistive biochips for biomolecular recognition (DNA hybridization, antibody antigen interaction, etc.). Magnetoresistive chip surfaces are chemically treated, enabling the immobilization of probe biomolecules such as DNA or antibodies. Fluid handling is also integrated in the biochip. The proposed microsystem not only integrates the biochip, which is an array of 16times16 magnetoresistive sensors, but it also provides all the electronic circuitry for addressing and reading out each transducer. The proposed architecture and circuits were specifically designed for achieving a compact, programmable and portable microsystem. The microsystem also integrates a hand-held analyzer connected through a wireless channel. A prototype of the system was already developed and detection of magnetic nanoparticles was obtained. This indicates that the system may be used for magnetic label based bioassays     

A New Comb Circular Polarizer Suitable for Millimeter‐Band Application

This letter presents a new polarizer which has a simple comb structure inside a circular waveguide. The electrical performance of the proposed comb polarizer is optimized by a circular waveguide radius and by the physical parameters of the comb plates. This polarizer is suitable for providing good performance in millimeter‐band application because of its simple structure and low fabrication cost. In our experiments the dual‐band comb polarizer designed in band 1(K) and band 2(Ka) showed good electrical performance without any tuning elements.