PIN OLEDs — Improved structures and materials to enhance device lifetime

Abstract— Currently, three issues are identified that decide upon the commercial success of organic light‐emitting diodes (OLEDs), both in display and lighting applications: power efficiency, lifetime, and price competitiveness. PIN OLEDs are widely seen as the preferred way to maximize power efficiency. Here, it is reported that this concept also delivers the world longest lifetimes. For a highly efficient deep‐red PIN OLED, a half‐lifetime of 25,000 hours for a starting brightness of 10,000 cd/m² and a minimal voltage increase over lifetime is reported. This value corresponds to more than 1 × 10⁶ hours at 1000 cd/m² using an exponent of n = 1.7, which was measured by driving the OLEDs at different starting luminances. Because there is no initial luminance drop, these PIN OLEDs also exhibit a very high 80% lifetime (>300,000 hours at 1000 cd/m²). New record lifetime values for blue and green will be reported as well. Additionally, further topics that have impact on the production yield and cost such as the newly developed air‐stable organic n‐doping material NDN‐26 and top‐emitting structures will be discussed.     

Millisecond step-scan FT-IR transmission spectroscopy under transient reaction conditions: CO oxidation over Pt/Al2O3

Time-resolved FT-IR spectra of CO oxidation over Pt/Al₂O₃ catalysts were collected in situ in transmission mode under transient reaction conditions. Using the step-scan acquisition mode of a commercial FT-IR spectrometer, time-resolution of a few milliseconds, compared to several hundred milliseconds in the normal rapid-scan mode, could be achieved. The experiments were triggered by reproducible oxygen gas pulses at constant temperature. Infrared light transmission, uniform heating and fast gas exchange were realized by pressing the pure catalyst powder onto a thin stainless steel wire mesh using a low volume reaction cell. By comparing the results of both acquisition modes, rapid-scan and step-scan, we will demonstrate, that it is possible, in a rather simple way, to investigate heterogeneously catalysed reactions under reaction conditions by means of FT-IR spectroscopy with time-resolutions down to a few milliseconds, and, in principle, lower. CO oxidation between 443 and 573 K over 1%Pt/γ-Al₂O₃ and 4%Pt/γ-Al₂O₃ catalysts has been investigated as a test reaction. By using the high time-resolution of the step-scan acquisition mode we could obtain new details of the dynamics of the CO oxidation reaction over a supported Pt catalyst at high temperatures and 1 atm pressure.     

DRAG REDUCTION IN ARTIFICIALLY ROUGHENED PIPES

The influence of an extremely rough surface on the drag reducing properties of polymer solutions is studied by pressure drop measurements in a rough pipe. It is shown that the onset of drag reduction for a homogeneous dilute polymer solution in a rough pipe occurs at the same wall shear stress as in a smooth pipe of the same diameter. In addition, the maximum drag reduction is almost the same in both types of pipes. Similar results are found for so-called heterogeneous drag reduction obtained by injecting a concentrated polymer solution in the centre of the pipe. The injected polymer solution, which is convected along the centre of the pipe as an elastic thread, disintegrates into fine polymer threads in the rough pipe leading to an increased drag reduction. In this case the injection of the same amount of polymer in the form of a concentrated solution is more effective than a homogeneous polymer solution.     

Impact of Si on Microstructure and Mechanical Properties of 22MnB5 Hot Stamping Steel Treated by Quenching & Partitioning (Q&P)

Based on 22MnB5 hot stamping steel, three model alloys containing 0.5, 0.8, and 1.5 wt pct Si were produced, heat treated by quenching and partitioning (Q&P), and characterized. Aided by DICTRA calculations, the thermal Q&P cycles were designed to fit into industrial hot stamping by keeping partitioning times ≤ 30 seconds. As expected, Si increased the amount of retained austenite (RA) stabilized after final cooling. However, for the intermediate Si alloy the heat treatment exerted a particularly pronounced influence with an RA content three times as high for the one-step process compared to the two-step process. It appeared that 0.8 wt pct Si sufficed to suppress direct cementite formation from within martensite laths but did not sufficiently stabilize carbon-soaked RA at higher temperatures. Tensile and bending tests showed strongly diverging effects of austenite on ductility. Total elongation improved consistently with increasing RA content independently from its carbon content. In contrast, the bending angle was not impacted by high-carbon RA but deteriorated almost linearly with the amount of low-carbon RA.     

The influence of type and token frequency on the acquisition of affixation patterns: Implications for language processing.

Rules, and exceptions to such rules, are ubiquitous in many domains, including language. Here we used simple artificial grammars to investigate the influence of 2 factors on the acquisition of rules and their exceptions, namely type frequency (the relative numbers of different exceptions to different regular items) and token frequency (the number of exception tokens relative to the number of regular tokens). We familiarized participants to either a prefixation pattern (where regulars started with /ZaI/ and exceptions ended with /ZaI/) or a suffixation pattern (where regulars ended with /ZaI/ and exceptions started with /ZaI/). We show that the type and the token frequency of regular items and exceptions influence in different ways what participants can learn. For the exceptions to be learned, they have to occur sufficiently often so that participants can memorize them; this can be achieved by a high token frequency. However, a high token frequency of the exceptions also impaired the acquisition of the regular pattern. In contrast, the type frequency of the patterns seemed to determine whether the regular pattern could be learned: When the type frequency of the regular items was sufficiently high, participants successfully learned the regular pattern even when the exceptions were played so often that 66% of the familiarization items were exceptions. We discuss these findings in the context of general learning mechanisms and the role they may play in language acquisition. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

CASA: A knowledge-based tool for management consultants

The objective of strategic management consultant work is a comprehensive evaluation of the ethical values of the management, the capabilities of the employees and the performance of the administrative systems in order to develop a well-suited corporate strategy. In order to fulfill all these requirements the management consultants have to take into consideration several hundred data. The human information processing capacity allows in such situations only the intuitive and condensed assessment of the strategic corporate status quo. The knowledge-based system CASA (Computer Aided Strategy Audit) assists the management consultant during the process of enterprise segmentation in order to create strategic business units, the analysis of the corporate culture, the assessment of market and competition, and the strategic cost situation. The system is used now since the CeBIT fair 1989, and includes: 5-MB code and help texts, 2000 rules in 44 knowledge bases and 200 pages of automatically generated reports and up to 100 business charts. The use of CASA reduces the costs for the management consultancy to 30% of the original costs, i.e., from $75,000 to $25,000 for a strategy development project.     

Local Structure Effects on Pressure Drop in Slender Fixed Beds of Spheres

For slender fixed beds, the void fraction and flow properties are complex topics. Different factors can influence the local bed structure. For statistical analysis, 2800 fixed beds have been generated and the impact of friction factor and reactor-to-particle diameter ratio on the distribution has been shown. With particle-resolved computational fluid dynamics, all local structure effects are taken into account for the flow simulations. Pressure drop measurements and simulations showed that these effects can lead to areas with low flow resistance, leading to overestimated pressure drop by typical correlations up to 85 %.     

Mesoporous AlPO4 Glass from a Simple Aqueous Sol–Gel Route

Transparent and colorless AlPO₄ gel and glass are prepared via a simple aqueous sol–gel route using aluminum lactate and phosphoric acid as precursors. The stoichiometric AlPO₄ glass derived from this sol–gel route has a mesoporous structure with a surface area of 504 m²/g after calcination to 600°C. With increasing gel-to-glass processing temperature, the average degree of P/Al connectivity increases. After sample calcination at 600°C for 4 h, ²⁷Al MAS NMR spectra indicate that aluminum is almost completely converted into AlO₄ units. ²⁷Al{³¹P} rotational echo double resonance and ³¹P{²⁷Al} rotational echo adiabatic passage double resonance NMR experiments as well as ²⁷Al and ³¹P MAS NMR results further confirm that the prepared AlPO₄ glass has a three-dimensional network based on alternating Al(OP)₄ and P(OAl)₄ tetrahedral units in analogy to the local structure of crystalline AlPO₄.