Hydrogen evolution by templated cadmium indate nanoparticles under natural sunlight illumination

Carbon-doped cadmium indate (CdIn₂O₄) nanoparticles were synthesized by a sol–gel templating method using the block co-polymer surfactant Pluronic F127 and evaluated for hydrogen generation activity under artificial and natural solar illumination. Each catalyst powder was loaded with platinum as a cocatalyst in order to promote charge carrier separation. BET surface area measurements indicated an increase in surface area with F127 introduction of up to 5 times the area of the non-templated sample. Natural sunlight illumination experiments showed the hydrogen evolution rate of CdIn₂O₄ was 17 μmol h⁻¹ as compared to 2.1 μmol h⁻¹ for the Pt:TiO₂ reference material. The H₂ rate was determined to be similar under both stirring and non-stirring conditions for the CdIn₂O₄ catalyst, which resulted from 10 min irradiation exposure times. Laboratory experiments confirmed this effect and showed that at longer, out to 60 min, irradiation times the evolution rate was 3 times greater for stirred over non-stirred samples. The templated nanoparticle CdIn₂O₄ catalysts are promising for solar hydrogen conversion.     

Properties of purified direct steam grown silicon thermal oxides

Thermal silicon oxides are known to very effectively passivate silicon surfaces. Choosing a water vapor ambient instead of a dry oxygen atmosphere increases the oxidation rate by about one order of magnitude and considerably reduces process time and costs. State of the art pyrox systems produce steam by pyrolysis of hydrogen and oxygen gas. A new approach is the purification of vaporized deionized (DI) water. In this work we present a direct comparison of both steam generation systems, which are connected to the same quartz tube of an industrial high quality tube furnace. The higher steam saturation of the direct steam process enhances the growth rate by about 20% compared to a pyrolytic steam based process. On low-resistivity p-type substrates, excellent surface recombination velocities of around 25 cm/s are found for both systems after a forming gas anneal. Detailed characterization shows similar physical properties of the oxide layers grown by either steam from pyrolysis or purified steam. Moreover, thermal oxide rear surface passivated silicon solar cells show similar high efficiencies exceeding 18.0% irrespective of the applied steam generation technology.     

SEM study of the morphology of asymmetric cellulose acetate membranes produced from recycled agro-industrial residues: sugarcane bagasse and mango seeds

Cellulose, obtained both from sugarcane bagasse and mango seeds, was used for synthesizing cellulose acetate in order to produce asymmetric membranes. These were compared to membranes of commercial cellulose acetate (Rhodia). All produced membranes were asymmetric, characterized by the presence of a dense skin and a porous support. Differences regarding the morphology of the surfaces as well as of the porous support can be noticed. Scanning Electron Microscopy (SEM) showed that the morphology of the superficial layer, responsible for transport, depends on the different lignin content of the starting material and also on the viscosity average molecular weight of the cellulose acetates produced from sugarcane bagasse, mango seed, and Rhodia’s commercial cellulose acetate.     

Asymmetric buckling of shell-stiffened annular plates

The present study is devoted to some stability problems of annular plates with shell-stiffening. The plate is simply supported, or clamped, or elastic restrains are applied on the boundaries of the plate. Though the load is axisymmetric we shall assume that the deformations are not necessarily axisymmetric. The displacement fields in the plate and the shell are expanded into Fourier series. For the shell all physical quantities are derived from an appropriately chosen Galerkin function. The main goal is to clarify the effect of a stiffening shell on the buckling load. Hence the field equations together with the boundary- and continuity conditions are clarified. These provide the eigenvalue problem from which the critical load can be calculated. In order to solve the eigenvalue problem we have established, appropriate numerical methods are used.     

Influence of Zn2+ doping on the morphotropic phase boundary in lead-free piezoelectric (1 – x)Na1/2Bi1/2TiO3-xBaTiO3

A series of morphotropic phase boundary (MPB) compositions of (1–x)Na_1/2Bi_1/2TiO₃-xBaTiO₃ (x = 0.05, 0.055, 0.06, 0.065, 0.07), with and without 0.5 mol% Zn-doping was synthesized using the solid-state route. The samples were characterized using X-ray diffraction, dielectric analysis, and electromechanical measurements (piezoelectric d₃₃ coefficient, coupling factor k_p, mechanical quality factor Q_m, and internal bias field E_bias). The increase in the ferroelectric-relaxor transition temperature upon Zn-doping was accompanied by a shift of the MPB toward the Na_1/2Bi_1/2TiO₃-rich side of the phase diagram. Higher tetragonal phase fraction and increased tetragonal distortion were noted for Zn-doped (1 – x)Na_1/2Bi_1/2TiO₃-xBaTiO₃. In addition, ferroelectric hardening and the presence of an internal bias field (E_bias) were observed for all doped compositions. The piezoelectric constant d₃₃ and the coupling coefficient k_p decreased by up to ∼30%, while a 4- to 6-fold increase in Q_m was observed for the doped compositions. Apart from establishing a structure–property correlation, these results highlight the chemically induced shift of the phase diagram upon doping, which is a crucial factor in material selection for optimal performance and commercialization.     

On the electrochemical migration mechanism of tin in electronics

Electrochemical migration (ECM) of tin can result in the growth of a metal deposit with a dendritic structure from cathode to anode. In electronics, such growth can lead to short circuit of biased electrodes, potentially leading to intermittent or complete failure of an electronic device. In this paper, mechanistic aspects of ECM of tin are discussed in detail, using experimental results on ECM of tin in various environments and varying potential bias. Results on the formation of local pH changes by the electrodes and experiments observations are combined with thermodynamic stability of tin species as depicted in the Pourbaix diagram.     

BiFeO3 films on steel substrate by the citrate method

We deposited BiFeO₃ films on stainless steel substrates using a simple low-temperature wet-chemical route. Bismuth and iron nitrates were used as metal source and citric acid as chelating agent to prepare a water solution and deposit the film by dipping the steel substrate in the viscous solution. We have investigated the composition, crystallinity and structure of the BiFeO₃ film on steel by X-ray diffraction, X-ray photoelectron spectroscopy, high resolution scanning electron microscopy, conventional and high resolution transmission electron microscopy, and energy dispersive spectroscopy techniques. The film deposited on the steel substrate has two sublayers: a very thin (about 100 nm) nanocrystalline layer, with crystallite size of few nanometers, and a thicker (below 1 μm) crystalline layer.     

Morphology of Single-Component Particles Produced by Spray Pyrolysis

ABSTRACT

This work is a review of the experimental results from the literature for single-component metal and simple metal-oxide particles. Criteria for correlating particle morphology, i.e., whether the particles are solid or hollow, with process parameters and material properties during spray pyrolysis are presented and compared with the data available in the literature. The materials were classified into two categories for which the precursor: (1) melts and (2) does not melt before chemical reaction takes place, and separate criteria were used for each category based on the work of Jayanthi et al. (1993) J. Aerosol Sci. 19:478. In systems where the precursor melts before chemical reaction occurs, e.g., decomposition of nitrates of Mg, Al, Fe, Zn, Pb, Ni, Co, Pd, Mn, Cu, Sr, and Ag, the particle morphology is determined primarily by the densities and formula weights of the reactant and product compounds unless high temperature densification or puffing up of the particles due to gases evolved during the chemical reaction alter the morphology. In systems where the precursor undergoes nucleation to form a solid crust which does not melt before chemical reaction takes place, e.g., Ba(C₂H₃O₂)₂, Al₂(SO₄)₃, Zr(C₂H₃O₂)₂, and Zn(C₂H₃O₂)₂, solubility and density of the precursor as well as the operating temperature are the main factors that affect the product particle morphology. Overall, particle morphologies predicted by the criteria were in agreement with experimental observations reported in the literature.     

Stocking wild adult Florida largemouth bass (Micropterus salmoides floridanus): An additional fish management tool

Stocking of largemouth bass is an important management tool for fish management. The stocking of hatchery‐produced fingerling or advanced‐fingerling bass to supplement bass year‐classes, however, has exhibited varying success. Utilizing a different approach, a multiyear stocking programme using wild adult largemouth bass was initiated at the Harris Chain of Lakes (3800 ha Lake Griffin; 1811 ha Lake Dora) in central Florida. Wild adult bass (24 781 fish), ranging in size from 200 mm total length (TL) to over 600 mm TL, were stocked in Lake Griffin (13 932 fish) and Lake Dora (10 849 fish). One month after stocking, the number of stocked bass caught in electrofishing catches in Lake Griffin and Lake Dora was ~10% and 22%, respectively. Estimates of mortality were similar to the native largemouth bass, although the movement of stocked fish into other connecting water bodies was extensive. For the Lake Griffin/Lake Dora stocking programme, bass were transferred at a cost of $10.09–19.89 per fish, depending on how the costs of the project are calculated ($250 000 for just the capture and transport of the fish vs. $492 775 for the total project). Considering only capture and transport costs, conservative benefit/cost ratio estimates would be $1.77/$1.00 spent for replacement and $1.85/$1.00 spent recreational costs, although the benefit/cost ratios could exceed $10/$1. Based on the present study, stocking wild adult largemouth bass is a cost‐effective tool for managing largemouth bass.