多功能滚齿机的数字控制系统

本文叙述了以ＳＴＤＰＣ／ＸＴ（或ＰＣ／ＡＴ）机为主要核心构成的滚齿机数字控制系统的结构，软件设计和特点，系统采用混合语言编程，极大地提高了软件设计的灵活性与快速性，也分析了ＣＮＣ系统的加工过程，提出了加工中的软件预处理控制方法，并给出了轴伺服控制的并行算法分析与实现。     

高功率CO2激光器换热性能的研究

高功率CO2气体激光器的换热性能好坏是器件长期稳定运行的关键环节之一。本文以板翅式热交换器为例阐明了热交换器的计算和设计方法。     

面向大规模定制的虚拟设计研究

综述了大规模定制的范围经济性和面向大规模定制的基本设计方法，并提出了一个虚拟设计框架，该框架改变了传统的设计模式，利用先进的设计方法学和仿真支撑技术为产品开发提供了最大柔性和敏捷性。同时，它提供了一个多学科合作的设计环境，用户直接参与进设计循环中。最后，结合新型剑杆织机的开发，展示了一个能够支持新产品快速成功开发的虚拟设计环境。     

Three‐dimensionally braided carbon fiber–epoxy composites,a new type of material for osteosynthesis devices. I. Mechanical properties and moisture absorption behavior

In recent years, three‐dimensionally (3D) braided composites have attracted a great deal of attention because of their high‐impact damage tolerance and fatigue life, superior fracture toughness, and so forth, and have been used in aeronautics, military, and transportation. These advantages make them strong candidates for osteosynthesis devices. In this study, 3D braided carbon fiber–epoxy (C_3D/EP) composites were produced via a simple vacuum impregnation technique. The load‐deflection curve, mechanical properties, and influence of fiber volume fraction, braiding angle, and axial reinforcing fibers were examined to determine their suitability for internal fixation devices. It is found that the C_3D/EP composites have excellent toughness and do not show brittleness when fractured because of their relatively high void content. The flexural, shear, and impact strengths of the C_3D/EP composites are excellent. It was shown that a C_3D/EP composite with a stiffness similar to load‐bearing bones can be made while maintaining enough strength. It is concluded that a relatively higher void content and braiding angle is more suitable for the C_3D/EP composites from the viewpoint of requirements of fracture fixation materials. The moisture absorption behavior and changes in mechanical properties caused by moisture uptake were evaluated. Results show that absorbed moisture slightly decreases mechanical properties of the C_3D/EP composites. Contrary to the unreinforced epoxy, the moisture absorption behavior of the C_3D/EP composites cannot be described with Fick's law of diffusion, probably because of the presence of voids and/or 3D fiber structure. The exact mechanisms should be proposed in further investigations. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 85: 1031–1039, 2002     

Hilar cholangiocarcinoma: thin-section spiral CT findings with cholangiographic correlation

Hilar cholangiocarcinoma, a highly lethal tumor, is difficult to diagnose with conventional computed tomography (CT) because of its small size. Spiral CT allows more effective evaluation of these small lesions and better demonstrates the status of the hepatic arterial or portal venous circulation. Among 27 patients with hilar cholangiocarcinoma (infiltrative in 21, exophytic in two, polypoid in one, diffuse in three), thin-section spiral CT allowed identification of each tumor as an area of focal wall thickening that obliterated the lumen. Seventeen of the infiltrative tumors (81%) showed high attenuation. Identification of the level of biliary obstruction was possible in 63% of the patients (17 of 27). The level of obstruction was underestimated in six patients and overestimated in four. Spiral CT is a valuable method for diagnosis of hilar cholangiocarcinoma; however, spiral CT is less accurate in evaluation of intraductal tumor extent because of the limited z-axis resolution.     

水平井生产测井技术应用

通过技术合作，对水平井生产动态监测测井技术进行了探索，取得了一定效果。介绍了水平井产出剖面测井的关键技术。介绍了将测井仪器送入水平钻穿的地层中的3个传输测井工艺，包括钻杆传输方法、柔性管传输方法和井下牵引输送方法；介绍了所采用的测井系列，重点分析解决油汽水三相分离问题的测井方案；介绍了水平井测井资料的解释和评价技术；通过模拟实验，确定井中4种流体流型，提出持液率关系式和流量测井响应关系式。     

开发PROFIBUS-DP智能从站

简单介绍了PROFIBUS－DP现场总线，同时讨论了利用89C52单片机和PROFIBUS－DP从站芯片SPC3开发PROFIBUS－DP智能从站的软硬件设计方法。     

安钢宽板坯连铸机达产实践

分析了安钢宽板坯连铸机在热试车期间出现的生产问题,总结出制约生产主要因素,制定针对性措施,使该连铸机在较短时间内实现达产创效.     

应用人工神经网络优化五点法水平井井网

水平井直井联合布井方式越来越多地应用到油田的实际开发中，但是井网的选择与优化方面的研究比较少，特别是没有根据不同开发阶段变化的生产动态对水平井井网进行优化。应用人工神经网络技术，在进行数值模拟计算的基础上，制作样本并训练网络，可预测任意面积、任意水平井长度下的五点法水平井井网在不同开发阶段的生产动态，优化出不同生产时间和不同井网面积条件下最优井网穿透比，即生产10a时最优井网穿透比为0．55～0．8。与数值模拟结果进行对比，最大误差在1％以内，表明这种方法既快速简便又具有较高的精确性，可以有效地指导五点法水平井井网优化设计。