NMR束缚流体体积确定方法及其应用条件

NMR测井不能直接测定束缚流体饱和度（Swir）和束缚总流体（BVI）体积，而是根据T1分布和有效孔隙度（φe）间接确定。其精度取决于解释T2分布所选用的方法及其相关参数。NMR测井确定VBI方法有T21截止值方法，频谱BVI（简称SBVI）方法和BVI加权函数方法。     

预应力钢-混凝土组合梁的应用与研究

回顾了预应力钢 混凝土组合梁国内外应用与研究历史 ,分析了现有规范及理论的不足 ,并指出了有待解决的问题。     

低乙烯含量抗冲聚丙烯的结构表征

采用二甲苯为溶剂，将不同乙烯含量（５％￣１５％质量）的抗冲聚丙烯用特定程序进行分级，将各样品分为室温下可溶于甲苯和不可溶于甲苯的两部分。使用＾１３Ｃ－ＮＭＲ方法和ＦＴ－ＩＲ方法对各组分进行表征，明确了乙烯链段在聚丙烯链上的分布，并在此基础上提出了产生这种链结构的聚合工艺的特点。     

Stress distribution on [100] Si wafer mapped by novel I-V analysis of MOS tunneling diodes

The current-voltage (I-V) characteristics of metal-oxide-semiconductor tunneling diodes distributed over a 3-in Si wafer were analyzed to investigate the stress distribution on the wafer. Generally, the substrate injection saturation current (J/sub sat/) decreases as the gate injection leakage current (J/sub g/) increases, the latter being dominated by oxide thickness via a trap related mechanism. A universal curve to fit all analyzed data was found and it is suggested that devices with extremely high (low) J/sub sat/ at a given J/sub g/ should be located in areas of the silicon lattice with relatively high external compressive (tensile) stress because of the stress-induced bandgap variation effect. The mapped locations of the highly stressed devices on a 3-in [100] Si wafer correspond to the patterns of slips caused by thermal stress during rapid thermal processing, as described in previous reports.     

螺旋翅片管的换热计算

本文引入区域平均表面传热系数的概念。在实验研究的基础上进行了肋基和肋端温度分布预测及肋片换热数值计算。     

烷基烷氧基硅烷的合成方法及其在涂料中的应用

介绍了烷基烷氧基硅烷的合成方法(包括烷基的引入方法和烷氧基的形成方法)、近几年来在涂料中的应用及其结构与性能的关系。     

烃类在三甘醇和四甘醇中无限稀释活度系数的测定与关联

用气相色谱法分别测定了苯、甲苯、乙苯、正庚烷、正辛烷、正壬烷和正癸烷在三甘醇和四甘醇中的无限稀释活度系数 ,测定温度范围为 5 0～ 13 0℃。用修正的UNIFAC模型 (Dortmund)对上述不同温度下的无限稀释活度系数实验数据进行关联 ,得到了三甘醇和四甘醇与其它基团的相互作用参数 ,并将计算结果与实测值进行了比较。     

智能温湿度测控仪

本文提出一种利用MCS-51系列单片机实现温湿度自动检测和控制的智能仪表,文中对仪器的工作原理、硬件组成和软件设计作了较为详细的介绍。     

Synthesis of ultrafine LiCoO2 powders by the sol-gel method

Ultrafine high-temperature (HT) LiCoO₂ powders were synthesized by the sol-gel method using polyacrylic acid (PAA) as a chelating agent. The decomposition process of the gel precursor was examined to determine the crystallization temperature and the dependence of the physicochemical properties of HT-LiCoO₂ powders on the PAA quantity was extensively investigated. Polycrystalline HT-LiCoO₂ powders, composed of very uniformly sized ultrafine particulates with an average particle size of 30–50 nm and a specific surface area of 2.3–17 m²g^–1, could be obtained at the lower calcination temperature of 550 °C and the shorter calcination time of 1 h compared to the solid-state reaction.     

CAD OF MILLIMETER WAVE OSCILLATORS WITH THE FDHB TECHNIQUE

In this paper the modelling, analysis and optimization of millimeter wave oscillatorsare investigated by using the a frequency-domain harmonic balance technique (FDHB), where theexternal-circuit impedances looking outside from the active device are calculated with a combinedtechnique of modes expansion, Galerkin, and collocation methods. The optimization results arein agreement with the experimental ones, which show the reliability of the presented model andoptimization.