改性玻纤增强尼龙610,1010塑料

研究了采用(准)中粘度级尼龙做基体树脂,加入成核剂改善尼龙的结晶过程,提高结晶速率和初始熔融温度;添加光、热氧稳定剂,防止尼龙在成型加工和使用过程中产生降解与老化,提高塑料制品的质量和减少性能的分散性;采用合理的工艺条件,确保添加剂的均匀分散与减少玻纤的磨损,得到适于军工、航空和机电等领域需要的高性能的受力结构工程塑料。     

An electromigration failure model for interconnects under pulsedand bidirectional current stressing

An electromigration failure model which can be used to project the electromigration lifetime under pulsed DC and AC current stressing has been reported. The experimental results indicate that different metallization systems (Al-2%Si, Al4%Cu/TiW, and Cu) show similar failure behaviors, which can be explained and predicted by this model. The pulsed DC lifetime is found to be longer than DC lifetime, and the AC lifetime is found to be very much longer. This recognition can provide significant relief to circuit designs involving metals carrying pulsed DC and AC currents, and allow a more aggressive design to improve circuit density and speed     

秦山核电厂蒸汽发生器水位控制试验

简要介绍了蒸汽发生器水位控制系统的运行方式和试验方法。试验项目包括旁通阀控制试验、主给水阀控制试验和旁通阀与主给水阀的切换试验。文中给出了试验结果,即在液位扰动和核动率扰动时,蒸汽发生器液位的变化过程。经过两个月的运行和瞬态试验,证明蒸汽发生器水位控制系统满足设计要求。     

Flammability and thermal stability studies of ABS/Montmorillonite nanocomposite

Acrylonitrile–butadiene–styrene (ABS)/montmorillonite nanocomposites have been prepared using a direct melt intercalation technique by blending ABS and organophilic clay of two different particle sizes: OMTa (5 µm) and OMTb (38 µm). Their structure and flammability properties were characterized by X‐ray diffraction, high resolution electronic microscopy (HREM), thermogravimetric analysis (TGA) and cone calorimeter experiments. The results of HREM showed that ABS/5 wt% OMTa nanocomposite was a kind of intercalated–delaminated structure, while ABS/5 wt% OMTb nanocomposite was mainly an intercalated structure. The nanocomposites showed a lower heat release rate peak and higher thermal stability than the original ABS by TGA and cone calorimeter experiments. Also, the intercalated nanocomposite was more effective than an exfoliated–intercalated nanocomposite in fire retardancy. Copyright © 2003 Society of Chemical Industry     

Semiconductor optical amplifier for CWDM operating over 1540-1620 nm

A semiconductor optical amplifier was developed for coarse wavelength-division-multiplexing (CWDM) operating over 1540-1620 nm (C-L band). A unique quantum-well structure was designed to meet the requirements for the CWDM operation such as wide bandwidth, low polarization-dependent gain, and high-saturation power at the short wavelength end of the band (1540 nm). Over the band, 24-dB maximum chip gain was obtained with less than 4.3-dB gain flatness and more than 14.6-dBm saturation power.     

Material removal and surface damage in EDM of Ti3SiC2 ceramic

Material removal and surface damage of Ti₃SiC₂ ceramic during electrical discharge machining (EDM) were investigated. Melting and decomposition were found to be the main material removal mechanisms during the machining process. Material removal rate was enhanced acceleratively with increasing discharge current, i_e, working voltage, u_i, but increased deceleratively with pulse duration, t_e. Microcracks in the surface and loose grains in the subsurface resulted from thermal shock were confirmed, and the surface damage in Ti₃SiC₂ ceramic led to a degradation of both strength and reliability.