钨合金圆筒爆破试验破片分布的统计分析

采用圆筒爆破试验方法研究了易碎型钨合金的破片分布特征,并与93W合金的结果进行了对比.对破片的数量和质量分布特征进行了统计分析,发现易碎型钨合金的破片率明显高于93W合金,而且破片的均匀性也明显好于93W合金,但易碎钨合金的破片回收率低于93W合金,而且受装药量的影响较大.     

高温预析出对Al-Zn-Mg系铝合金时效硬化和应力腐蚀的影响

研究了高温固溶后降温处理工艺对中强可使预析出LC52和7039铝合金的组织、时效硬化和应力腐蚀的影响。金相观察发现,高温预析出可优先在晶界处产生,并提高随后时效状态下晶界析出相的不连续分布程度,温度降低到一定程度晶内和晶界产生大量析出。合金拉伸性能和应力腐蚀结果表明,预析出在保持强度和塑性的同时,可提高抗应力腐蚀性能。而预析出温度降低,合金强度呈下降趋势。     

在不断创新中开创新的百年——水口山有色金属集团有限公司110年创新发展历程和展望

回顾了水口山有色金属集团有限公司的发展历程，概述了取得的技术进步和主要成就．提出了企业今后的发展方向。     

JOINING MECHANISMS OF β''''-Al2O3 CERAMIC AND PYREX GLASS TO Al MATRIX COMPOSITE

The bonding of β'-Al2O3 and pyrex glass to Al matrix composites by anodic bonding process is achieved. The microstructure of the bonded interface and the joining mechanisms are analyzed with scanning electron microscope (SEM), energy dispersive X-ray fluorescence spectrometer (EDX). It is observed that the bonding region across the interface consists of the metal layer, oxide transitional layer and the ceramic layer, with the transitional layer composed of surface region and sub-surface region. The bonding process can mainly be categorized into anodic bonding process and solid state diffusing process. The pile-up of the ions and its drift in the interface area are the main reasons for anode oxidation and joining of the interface. The temperature, voltage and the drift ions in the ceramic or glass during the bonding process are the essential conditions to solid state diffusing and oxide bonding at the interface. The voltages, temperature, pressure as well as the surface state are the main factors that influence the anodic bonding.     

电视导引头模型参考控制器设计

借鉴模型参考控制器的设计思想,采用经过线性二次型输出反馈控制后的系统作为参考模型,以它的输出作为期望输出,让实际输出跟随这个期望输出;二者的误差信号反馈到原系统的输入端,设计出一种模型参考控制器.经该控制器优化后,电视导引头系统的快速性可得到较大提高.参考模型可由RC网络或计算机软件来实现.     

The new structure of fibre glass reinforced plastics bolt

The develop actuality and direction of FRP (fibre glass reinforced plastics) bolt in the world are analyzed. The new type structure of FRP bolt was designed. Trial data indicate that, all kinds of capability target of this FRP bolt all achieve and exceed the country stand-ard, substitute present metal bolt, wood bolt and bamboo bolt and other side bolt, it can gain magnitude technology and economy benefit. FRP bolt mechanization product line produce ef-ficiency is high, its throughput a day are 750 base, this can meet demand of hit-small mining company.     

企业不但应该做大更应该做强

从入世的角度 ,分析了我国企业在重组过程中存在的问题 ,并指出了我国企业做强做大的紧迫性