皮革去污上光用乳化蜡的研制

采用石蜡、微晶蜡为主要原料 ,经实验选出了以水为稀释剂的乳化型皮革去污上光蜡。实验优化的配方为石蜡 12 .5 g ,微晶蜡 8.0 g ,硬脂酸 8.5g ,三乙醇胺 5 .5 g ,水量 70 (涂用 )或 130 g(喷用 )。反应条件为乳化时间 4 0min ,搅拌速度 5 0 0～ 70 0r/min ,乳化温度 90℃。制得上光剂产品的去污性能可与用去污剂单独处理的效果相当 ,亮度可达 6 6 .7。     

电容检测纱线传感器转换特性对纱线不匀率测试的影响

讨论了纱线测试中受电容检测纱线传感器转换特性的非线性影响，测得的条干不匀率值与纱线的实际条干不匀率值之间的差异，从理论上估计了纱线在不同的电容检测槽内测试时，由于其截面充满系数不同而引起的相对差异，并用试验数据加以验证。     

Selective and nonselective wet etching of Zn0.9Mg0.1O/ZnO

Wet etch rates at 25°C for Zn_0.9Mg_0.1O grown on sapphire substrates by pulsed laser deposition (PLD) were in the range 300–1100 nm · min⁻¹ with HCl/H₂O (5×10⁻³−2×10⁻² M) and 120–300 nm · min⁻¹ with H₃PO₄/H₂O (5×10⁻³−2×10⁻² M). Both of these dilute mixtures exhibited diffusion-limited etching, with thermal activation energies of 2–3 kCal · mol⁻¹. By sharp contrast, the etch rates for ZnO also grown on sapphire by PLD were much slower in similar solutions, with rates of 1.2–50 nm · min⁻¹ in HCl/H₂O (0.01–1.2 M) and 12–54 nm · min⁻¹ in H₃PO₄/H₂O (0.02–0.15 M). The etching was reaction limited over the temperature range 25–75°C, with activation energies close to 6 kCal · mol⁻¹. The resulting selectivity of Zn_0.9Mg_0.1O over ZnO can be a high as ∼400 with HCl and ∼30 with H₃PO₄.     

Olefins from conventional and heavy feedstocks: Energy use in steam cracking and alternative processes

Steam cracking for the production of light olefins, such as ethylene and propylene, is the single most energy-consuming process in the chemical industry. This paper reviews conventional steam cracking and innovative olefin technologies in terms of energy efficiency. It is found that the pyrolysis section of a naphtha steam cracker alone consumes approximately 65% of the total process energy and approximately 75% of the total exergy loss. A family portrait of olefin technologies by feedstocks is drawn to search for alternatives. An overview of state-of-the-art naphtha cracking technologies shows that approximately 20% savings on the current average process energy use are possible. Advanced naphtha cracking technologies in the pyrolysis section, such as advanced coil and furnace materials, could together lead to up to approximately 20% savings on the process energy use by state-of-the-art technologies. Improvements in the compression and separation sections could together lead to up to approximately 15% savings. Alternative processes, i.e. catalytic olefin technologies, can save up to approximately 20%.     

可编程计算器辅助测量施工放线

昌马水库工程是甘肃省重点工程，在施工中对测量放线要求较高，为了提高放线精度及效率，在放线中引入可编程序的casio fk一4500P计算器配合，迅速处理放线数据，取得了可喜的效果。     

Fabrication and characteristics of high-speed implant-confined index-guided lateral-current 850-nm vertical cavity surface-emitting lasers

Process technology of high-speed implant-apertured index-guide lateral-current-injection top dielectric-mirror quantum-well 850-nm vertical cavity surface-emitting lasers (VCSELs) has been developed. Oxygen and helium implantation for aperture definition and extrinsic capacitance reduction, dielectric mirror formation, p- and n-ohmic contact formation, VCSEL resistance, and thermal analysis were investigated. Employing this technology, GaAs/AlGaAs-based 850-nm VCSELs with small signal modulation bandwidths up to 11.5 Gb/s and an eye diagram generated at 12 Gb/s by a pseudorandom bit sequence of 2/sup 31/-1 were achieved. The bit-error rates were below 10/sup -13/. The threshold current is as low as 0.8 mA for 7-/spl mu/m-diameter current apertures and typical slope efficiencies of 0.45-0.5 mA/mW were obtained.     

添加CaF2-YF3的AlN陶瓷的热导率

用CaF2和YF3做添加剂，在1750℃制备了热导率高于170W/m.K的的AlN陶瓷，并用XRD和SEM研究了AlN陶瓷在烧结过程中的相组成，微结构以及晶格参数的变化，并讨论了其对热导率的影响，研究发现，当使用CaF2-YF3做添加剂时，微结构差异对AlN陶瓷热导率的影响很小，AlN陶瓷的热导率主要由AlN晶格氧缺陷浓度决定，由于CaF2-YF3能有效降低AlN颗粒表面的氧含量，从而有利于获得高的热导率。     

天然“药品”——蜂胶

主要介绍了蜂胶的营养成分、分类、质量标准、提取方式及保健功能。     

坑道用水下堵漏剂的研制

坑道水下堵漏剂的研制包括F－1、F－2和F－3型。其中F－1是一种有机堵漏剂，它可以在水中固化；F－2是一种无机防水堵漏剂，施工方便；F－3是速凝型，它可在瞬间固化，能对坑道的涌水口进行堵漏。