磁场中双量子位Heisenberg模型的纠缠与量子相变

以双量子位Heisenberg模型为例,讨论了磁场方向对纠缠的影响。结果表明：一定温度下,保持磁场的大小不变,仅改变其方向,不仅能获得最大纠缠,还产生了量子相变。     

Electrochemical and microstructural characterization of cyclic redox behaviour of SOFC anodes

The oxidation of Ni to NiO in solid oxide fuel cell (SOFC) anode will result in large bulk volume change, which may change the interfaces of the two phases in the anode cermet and thus may cause significant performance degradation. The reduction and oxidation (redox) of the Ni/YSZ cermet were studied at 800 ℃. Anodic polarization measurements were performed before and after redox cycles. The anode current density at an overpotential of 100 mV kept decreasing during the whole redox treatment. It decreased from 19.11 to 7.95 mA·cm-2 after two redox cycles. Anode supported unit cell was assembled for cell's discharge measurements. Cell performance declined after each redox cycle. The maximum power density decreased from 126.28 to 40.32 mW·cm-2 . The microstructural changes after redox cycling were recorded using scanning electron microscopy (SEM). The results reveal that after re-oxidation, the Ni gets coarse and has a higher porosity; the nickel network structure turns to be desultory.     

对Al-Cu合金中α-Al及Al2Cu生长行为的探讨

研究了Al-Cu合金中α-Al和Al2Cu的生长行为,分析了初生α-Al及初生Al2Cu作为共晶核心形核的能力.结果发现,在过共晶组织中,初生相Al2Cu形貌大部分有明显的拐角,观察其平面有的呈矩形,呈现小面生长特性.而α-Al与Al2Cu共晶生长时,Al2Cu择优生长特征削弱,与α-Al耦合生长呈现非小面-非小面生长,表明Al2Cu在不同的生长阶段表现出的生长行为不同.在亚共晶组织中,初生相α-Al周围形成离异共晶的Al2Cu,而过共晶组织中初生相Al2Cu周围没有离异共晶的α-Al,表明初生相Al2Cu作为共晶层片核心的能力比初生相α-Al作为共晶层片核心的能力强.     

自动焊机监测与参数化曲线控制系统设计

设计了自动焊机的监测与参数化曲线控制系统,以可视化方式为工艺人员改变焊接过程的控制参数提供了便利,该控制系统的数据库的数据存储与查询功能为工艺人员进行离线工艺分析提供了大量的数据,且该系统与焊机的数控系统密切配合,实现了焊接自动生产线的可靠监控.     

Ni-Cr-Fe-Si-B合金涂层及铝青铜基体熔合区组织的研究

采用钨极氩弧焊方法在铝青铜基体上施焊了Ni—Cr-Fe-Si—B合金涂层，并运用金相显微镜、扫描电子显微镜及能谱分析了喷涂层、熔合区及热影响区的组织形貌和成分分布。结果表明，喷焊时，在涂层与基体界面两侧各组元均发生了明显的扩散，Cu、Ni组元间可相互取代，基体融合区组织的基本组成仍为α (α γ2)，但同时也形成了Cu2FeAl7、NiAl3等新相，且融合区组织细小，涂层与基体间为冶金态结合。     

基于数值模拟的接水盘冲压成形工艺分析与设计

分析了冰箱接水盘的形状和结构特点 ,设计了零件的冲压成形工艺 ,运用板料成形有限元软件对其中的拉伸和翻边工艺进行数值模拟 ,得到成形过程中工件各部位的厚度分布和成形极限图 ,分析了在不同工艺条件下可能产生的缺陷及其原因 ,并确定其初始毛坯和中间毛坯的合理形状 ,有效地保证了成形工艺的可靠性     

Influence of electroplating conditions on magnetic properties of Fe-36wt.% Ni alloy film

A Fe-Ni soft magnetic film was prepared in sulphate solution by electroplating. The influences of the molar ratio of n [Fe2+ ]/ n [Ni2+ ], current density, bath temperature, pH and L-ascorbic acid concentration on magnetic properties of Fe-Ni alloy film were investigated. The results show that the saturated flux density(BS) of the film increases initially and decreases after it reaches the specific value with the increase of n [Fe2+ ]/ n [Ni2+ ] molar ratio, current density, bath temperature and pH. However, the relationship between L-ascorbic acid concentration and B S keeps linear. It is observed that the coercive force( Hc) is enhanced with the increase of n [Fe2+ ]/ n [Ni2+ ] molar ratio, current density and pH. By comparison, when the bath temperature increases, Hc always decreases. With the increase of L-ascorbic acid concentration, the coercive force increases initially and then decreases.     

冷轧工作辊摩擦不稳定分析及其抑制对策

对冷轧机工作辊由于摩擦力引起的垂直、横向振动作了定性分析，指出了它们的危害，提出了预防措施。     

中厚板轧机工作辊失效分析及对策

介绍了济钢中厚板厂使用国外高镍铬和高铬工作辊的主要失效形式 ,并对该工作辊的断裂和裂纹产生原因进行了分析 ,同时针对所存在的问题提出了对策和具体改进措施。     

基于Feeds的社交网络活跃度分析

从用户产生和消费Feeds的角度分析社交网络变得不活跃的原因,通过分析人人网某大学社区用户长周期的Feeds行为来探讨该社区用户活跃度的变化。通过对用户活跃性周期和Feeds时间间隔的分析,发现越来越多的用户产生Feeds的活跃度在下降,并导致其他用户接收到的信息流的流速和多样性下降。社交网络用户由于各种原因离开或变得不活跃,并通过信息流对其朋友圈形成负向反馈,这可能是社交网络变得不活跃的深层原因。模拟实验表明,30%的初始不活跃用户会使得整个社区的信息流快速下降,并导致整个社区不活跃。