Longitudinal air permeability of pinewood with beetle transmitted blue-stain

The mountain pine beetle epidemic is destroying an extensive volume of the lodgepole pine forests being one of the most commercially harvested trees in British Columbia. The purpose of this study was to test the permeability of wood of four different classes regarding the time of the beetle attack. The experiments used the ‘‘falling water’’ unsteady-steady method of measuring superficial air permeability. The results showed that the specific permeability is not significantly different between the infested classes tested. The same conclusion could be reached for comparisons of uninfected and infested wood.     

An improvement in the calculation of the magnetic field for an arbitrary geometry coil with rectangular cross section Int. J. Numer. Model. 2005; 18(6):493–504

The above article was published in Volume 18, Issue 6, Pages 493–504, (October 2005). A number of imperfections were subsequently identified and have been corrected below. On page 497, the following equation has been corrected to: On page 501, the following equation has been corrected to: On page 502, the following equation has been corrected to:      

Sensitivity of the Red River Basin Flood Protection System to Climate Variability and Change

An original modeling framework for assessment of climate variation and change impacts on the performance of complex flood protection system has been implemented in the evaluation of the impact of climate variability and change on the reliability, vulnerability and resiliency of the Red River Basin flood protection system (Manitoba, Canada). The modeling framework allows for an evaluation of different climate change scenarios generated by the global climate models. Temperature and precipitation are used as the main factors affecting flood flow generation. System dynamics modeling approach proved to be of great value in the development of system performance assessment model. The most important impact of climate variability and change on hydrologic processes is reflected in the change of flood patterns: flood starting time, peak value and timing. The results show increase in the annual precipitation and the annual streamflow volume in the Red River basin under the future climate change scenarios. Most of the floods generated using three different climate models had an earlier starting time and peak time. The assessment of the performance of Red River flood protection system is based on the flood flows, the capacity of flood control structures and failure flow levels at different locations in the basin. In the Assiniboine River Basin, higher reliabilities at downstream locations are obtained indicating that Shellmouth reservoir plays an important role in reducing downstream flooding. However, a different trend was identified in the Red River Basin. The study results show that flood protection capacity of the Red River infrastructure is sufficient under low reliability criteria but may not be sufficient under high reliability criteria.     

Development of new models for the estimation of deformation moduli in rock masses based on in situ measurements

Bulletin of Engineering Geology and the Environment - Knowledge of the deformation properties of the rock mass is essential for the stress–strain analysis of structures such as dams, tunnels,...     

Tribological Behavior of Composites Based on ZA-27 Alloy Reinforced with Graphite Particles

The objective of this investigation is to assess the influence of graphite reinforcement on tribological behavior of ZA-27 alloy. The composite with 2 wt% of graphite particles was produced by the compocasting procedure. Tribological properties of unreinforced alloy and composite were studied, using block-on-disk tribometer, under dry and lubricated sliding conditions at different specific loads and sliding speeds. The worn surfaces of the samples were examined by the scanning electron microscopy (SEM). The obtained results revealed that ZA-27/graphite composite specimens exhibited significantly lower wear rate and coefficient of friction than the matrix alloy specimens in all the combinations of applied loads (F _n ) and sliding speeds (v) in dry and lubricated tests. The positive tribological effects of graphite reinforcement of ZA-27 in dry sliding tests were provided by the tribo-induced graphite film on the contact surface of composite. In test conditions, characterized by the small graphite content and modest sliding speeds and applied loads, nonuniform tribo-induced graphite films were formed leading to the increase of the friction coefficient and wear rate, with increase of the sliding speed and applied load. In conditions of lubricated sliding, the very fine graphite particles formed in the contact interface mix with the lubricating oil forming the emulsion with improved tribological characteristics. Smeared graphite decreased the negative influence of F _n on tribological response of composites, what is manifested by the mild regime of the boundary lubrication, as well as by realization of the mixed lubrication at lower values of the v/F _n ratio, with respect to the matrix alloy.     

Isogeometric bending analysis of composite plates based on a higher-order shear deformation theory

This research paper presents an isogeometric plate finite element formulation for analysis of thick composite plates. Isogeometric finite element method which is based on non-uniform rational B-splines (NURBS) basis functions, is a novel numerical procedure developed to bridge the gap between CAD and FEM modeling of structures. In order to investigate the behavior of isogeometric plate elements under static loading, plate kinematics is based on third order shear deformation theory (TSDT) of Reddy, which is free from transverse shear locking. This paper discusses accurate transverse stress recovery procedures for TSDT isogeometric finite elements. Numerical experiments with quadratic, cubic and quartic elements are presented and obtained results are compared to other available ones.     

Multivariate statistical analysis of Raman images of a pharmaceutical tablet

This paper describes the application of principal component analysis (PCA) and independent component analysis (ICA) to identify the reference spectra of a pharmaceutical tablet's constituent compounds from Raman spectroscopic data. The analysis shows, first with a simulated data set and then with data collected from a pharmaceutical tablet, that both PCA and ICA are able to identify most of the features present in the reference spectra of the constituent compounds. However, the results suggest that the ICA method may be more appropriate when attempting to identify unknown reference spectra from a sample. The resulting PCA and ICA models are subsequently used to estimate the relative concentrations of the constituent compounds and to produce spatial distribution images of the analyzed tablet. These images provide a visual representation of the spatial distribution of the constituent compounds throughout the tablet. Images associated with the ICA scores are found to be more informative and not as affected by measurement noise as the PCA based score images. The paper concludes with a discussion of the future work that needs to be undertaken for ICA to gain wider acceptance in the applied spectroscopy community.