合成孔径雷达1553B通信接口设计与实现

介绍某型号合成孔径雷达系统的1553B总线通信接口设计方案与工程实现;方案采用国内自主研发的4M/s速率1553B总线接口芯片,PC/104工控机与FPGA结合,通过硬件系统设计和软件编程,实现对1553B总线数据收发和雷达部分辅助数据的提供,实现项目总体对1553B总线通信接口的要求。实际应用情况表明,该通信接口运行稳定、可靠,具有一定的实用性和良好的应用前景。     

Comparison of gas sensing properties based on hollow and porous α-Fe<Subscript>2</Subscript>O<Subscript>3</Subscript> nanotubes

Hollow and porous α-Fe₂O₃ nanotubes were successfully synthesized by single nozzle electrospinning method followed by annealing treatment. The crystal structures and morphologies of the as-prepared materials were characterized by X-ray diffraction and scanning electron microscopy, respectively. The as-prepared materials were applied to construct gas sensor devices which gas sensing properties were further investigated. The obtained results revealed that porous α-Fe₂O₃ nanotube gas sensors exhibit a markedly enhanced gas sensing performance compared with hollow α-Fe₂O₃ nanotube gas sensors, which was about three times higher to 100 ppm acetone at 240 °C. Interestingly, hollow and porous α-Fe₂O₃ nanotube gas sensors both showed fast response–recovery time and good selectivity, but the porous ones possessed the shorter recovery time. The improved properties could be attributed to the unique morphology of porous nanotubes. Thus, further improvement of performance in metal-oxide-semiconductors materials could be realized by preparation the unique porous structures of nanotubes. Moreover, it is expected that porous metal-oxide-semiconductors nanotubes could be further design as promising candidates for gas sensing materials.     

La<Subscript>1−x</Subscript>Ag<Subscript>x</Subscript>FeO<Subscript>3</Subscript>/halloysites nanocomposite with enhanced visible light photocatalytic performance

La_1?xAg_xFeO₃/halloysites nanotubes (HNTs) nanocomposite was synthesized by sol–gel method. It was characterized by X-ray diffraction, transmission electron microscope, Fourier transform infrared spectroscopy and UV–visible diffused reflectance spectroscopy measurements. The photo-activity of the La_1?xAg_xFeO₃/HNTs nanocomposite was evaluated via degradation of methylene blue (MB) under visible-light irradiation. The results showed that the HNTs with unique pore structure favored the adsorption of organic molecules. Adequate Ag⁺ doping improved the absorption ability for visible light. The La_0.95Ag_0.05FeO₃/HNTs demonstrated the best photocatalytic performance, which achieved as high as 99 % for MB degradation exposed 2 h irradiation. However,further increasing of Ag⁺ doping gradually reduced the photocatalytic activity. The nanocomposite catalyst showed outstanding recyclability after eight cycles which still remained up to 90 %.     

强磁场对硅锰铸钢于A_1点附近等温珠光体相变的影响

通过开展12 T强磁下硅锰铸钢(50Si_2Mn_3)于A_1点温度附近不同等温时间的热处理试验,并对比强磁场与无磁场条件下等温珠光体相变试验结果,研究了磁场对珠光体转变量及组织形貌的影响。研究表明,对于50Si_2Mn_3在A1点以下较高温度范围内,强磁场可缩短珠光体相变的孕育期,促进硅锰铸钢珠光体转变,使其转变量明显增加;强磁场能够提高珠光体转变临界点,使50Si_2Mn_3在A1点以上等温过程中能够发生珠光体相变。     

Aggregation-induced emission luminogen-assisted stimulated emission depletion nanoscopy for super-resolution mitochondrial visualization in live cells

Nano Research - Aggregation-induced emission luminogens (AIEgens) are fluorescent agents that are ideal for bioimaging and have been widely used for organelle targeting, cellular mapping, and...     

软件项目进度控制方法研究

为优化软件项目进度控制过程,使管理者能够对软件项目进度进行有效的跟踪和调整,研究并比较了主要的项目进度控制方法和技术,对甘特图、网络计划技术、关键链技术,对各技术的原理、适用范围、优缺点等进行了分析.为弥补上述技术的不足,引入工业项目进度控制方法--实际进度前锋线法,增强了对软件项目进度的信息统计和工期预测功能.通过对上述几种技术的改进和综合应用,提出了一个高效便捷的进度控制系统的设计方案.     

高层建筑结构力学模型仿真系统

该文介络了高层建筑结构力学模型仿真的理论基础、关键技术和实现途径,并简述了高层建筑结构多媒体仿真系统MSTB的设计特点。