Ultrafast Electron–Phonon Coupling at Metal-Dielectric Interface

Energy transfer from photo-excited electrons in a metal thin film to the dielectric substrate is important for understanding the ultrafast heat transfer process across the two materials. Substantial research has been conducted to investigate heat transfer in a metal-dielectric structure. In this work, a two-temperature model in metal was used to analyze the interface electron and dielectric substrate coupling. An improved temperature and wavelength-dependent Drude–Lorentz model was implemented to interpret the signals obtained in optical measurements. Ultrafast pump-and-probe measurements on Au-Si samples were carried out, where the probe photon energy was chosen to be close to the interband transition threshold of gold to minimize the influence of non-equilibrium electrons on the optical response and maximize the thermal modulation to the optical reflectance. Electron-substrate interface thermal conductance at different pump laser fluences was obtained, and was found to increase with the interface temperature.     

Performance investigation on a novel 3D wave flow channel design for PEMFC

Flow field structure can largely determine the output performance of Polymer electrolyte membrane fuel cell. Excellent channel configuration accelerates electrochemical reactions in the catalytic layer, effectively avoiding flooding on the cathode side. In present study, a three-dimensional, multi-phase model of PEMFC with a 3D wave flow channel is established. CFD method is applied to optimize the geometry constructions of three-dimensional wave flow channels. The results reveal that 3D wave flow channel is overall better than straight channel in promoting reactant gases transport, removing liquid water accumulated in microporous layer and avoiding thermal stress concentration in the membrane. Moreover, results show the optimal flow channel minimum depth and wave length of the 3D wave flow channel are 0.45 mm and 2 mm, respectively. Due to the periodic geometric characteristics of the wave channel, the convective mass transfer is introduced, improving gas flow rate in through-plane direction. Furthermore, when the cell output voltage is 0.4 V, the current density in the novel channel is 23.8% higher than that of conventional channel.     

0?1膨胀负二项回归模型在COVID?19疫情分析中的应用

在公共卫生等应用领域，经常会同时出现零观测值、一观测值较多的情况. 为更好地拟合这类数据，采用0?1膨胀负二项分布及其回归模型进行分析. 在数据扩充基础上，结合Pólya?Gamma潜变量对模型参数进行贝叶斯推断. 最后，对我国湖北省2019冠状病毒病(COVID?19)死亡数据集进行分析. 研究表明，0?1膨胀负二项回归模型能够达到更好的拟合效果.     

Evaluation of bismuth doped La2-xBixNiO4+δ (x = 0, 0.02 and 0.04) as cathode materials for solid oxide fuel cells

Bismuth doped La_2-xBi_xNiO_4+δ (x = 0, 0.02 and 0.04) oxides are investigated as SOFC cathodes. The effects of Bi doping on the phase structure, thermal expansion, electrical conduction behavior as well as electrochemical performance are studied. All the samples exist as a tetragonal Ruddlesden-Popper structure. Bi-doped LBNO-0.02 and LBNO-0.04 have good chemical and thermal compatibility with LSGM electrolyte. The average TEC over 20–900°С was 13.4 × 10^?6 and 14.2 × 10^?6 K^?1 for LBNO-0.02 and LBNO-0.04, respectively. The electrical conductivity was decreasing with the rise of Bi doping content. EIS measurement indicates Bi doping can decrease the ASR values. At 750 °C, the obtained ASR for LBNO-0.04 is 0.18 Ωcm², which is 56% lower than that of the sample without Bi doping, suggesting Bi doping is beneficial to the electrochemical catalytic activity of LBNO cathodes.     

Structural,optical and electrical properties of indium doped Cu2ZnSn(S,Se)4 thin films synthesized by the DC and RF reactive magnetron cosputtering

Element doping into the Cu₂ZnSn(S,Se)₄ (CZTSSe) absorber is an effective method to optimize the performance of thin film solar cells. In this study, the Cu₂In_xZn_1-xSn(S,Se)₄ (CIZTSSe) precursor film was deposited by magnetron cosputtering technique using indium (In) and quaternary Cu₂ZnSnS₄ (CZTS) as targets. Meanwhile, the In content was controlled using the direct current (DC) power on In target (P_In). A single kesterite CIZTSSe alloy was formed by successfully doping a small number of In³⁺ into the main lattice of CZTSSe. The partial Zn²⁺ cations were substituted by In³⁺ ions, resulting in improving properties of CZTSSe films. Morphological analysis showed that large grain CIZTSSe films could be obtained by doping In. The well-distributed, smooth, and dense film was obtained when the P_In was 30 W. The band gap of CIZTSSe could be continuously adjusted from 1.27 to 1.05 eV as P_In increased from 0 to 40 W. In addition, the CIZTSSe alloy thin film at P_In = 30 W exhibited the best p-type conductivity with Hall mobility of 6.87 cm²V^?1s^?1, which is a potential material as the absorption layer of high-performance solar cells.     

巧用华中系统复合循环G71指令车削零件

结合实例详解了华中数控系统复合循环指令G71在实际编程与加工中的应用。此指令的应用,解决了在加工轴类零件过程中运用传统的加工方法难以满足形状复杂、精度高等要求的问题,从而提高了工作效率。     

Densification mechanism during reactive hot pressing of B4C-ZrO2 mixtures

The densification behaviors of pure B₄C and B₄C-ZrO₂ mixtures were compared during hot pressing. The results showed that in-situ formed ZrB₂ effectively enhanced the densification process of B₄C-ZrO₂ mixtures, more significantly during the intermediate stage. Within the relative density ranging from 0.75 to 0.90, the B₄C-15?wt%ZrO₂ mixture (B15Z) achieved the maximum densification rate as twice much as that of pure B₄C. The stress exponent n>3 indicated plastic deformation was the dominant densification mechanism of B15Z. The viscosities of plastic flow were evaluated using Murray-Rodger-William equation and the viscosity of B15Z was only a quarter of that in pure B₄C. The sintering activation energy was calculated to be 305.9?kJ/mol for pure B₄C and 197?kJ/mol for B15Z, respectively. It was proposed that the lower viscosity of plastic flow and activation energy accelerated the sliding and propagating motions of plastic flow, by which underlain the enhanced densification behaviors of B₄C-ZrO₂ mixtures.     

Regulation of sensory nerve conduction velocity of human bodies responding to annual temperature variations in natural environments

The extensive research interests in environmental temperature can be linked to human productivity / performance as well as comfort and health; while the mechanisms of physiological indices responding to temperature variations remain incompletely understood. This study adopted a physiological sensory nerve conduction velocity (SCV) as a temperature‐sensitive biomarker to explore the thermoregulatory mechanisms of human responding to annual temperatures. The measurements of subjects’ SCV (over 600 samples) were conducted in a naturally ventilated environment over all four seasons. The results showed a positive correlation between SCV and annual temperatures and a Boltzmann model was adopted to depict the S‐shaped trend of SCV with operative temperatures from 5°C to 40°C. The SCV increased linearly with operative temperatures from 14.28°C to 20.5°C and responded sensitively for 10.19°C‐24.59°C, while tended to be stable beyond that. The subjects’ thermal sensations were linearly related to SCV, elaborating the relation between human physiological regulations and subjective thermal perception variations. The findings reveal the body SCV regulatory characteristics in different operative temperature intervals, thereby giving a deeper insight into human autonomic thermoregulation and benefiting for built environment designs, meantime minimizing the temperature‐invoked risks to human health and well‐being.