Synthesis and characterization of a novel proton‐exchange membrane for fuel cells operating at high temperatures and low humidities

The synthesis of a p‐toluidine/formaldehyde (PTF) resin was performed, and the effects of the molar ratio of the individual monomers and the polymerization conditions on the structure of the PTF resin were studied. Fourier transform infrared and ¹³C‐NMR spectra were used to characterize the PTF. Wide‐angle X‐ray diffraction patterns revealed the crystalline structures of various PTFs. Polarized optical microscopy revealed that the molar ratio of the monomers had a strong effect on the crystalline morphologies. A longer polymerization time turned out a polymer with a higher intrinsic viscosity and molecular weight, which led to differences in the proton conductivity. All of the PTFs showed a higher proton conductivity than a commercial Nafion membrane at 90–100°C and 0% relative humidity. The proton conductivity of the PTF series could be improved by sulfonation with sulfuric acid and could be maintained after blending with polyurethane. Pure methanol could be used as a fuel source because of the insolubility and nonwetting properties of PTF in methanol to increase the output current density for a PTF membrane electrode assembly. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2008     

λ-MnO2的结构与电性能研究

采用酸处理LiMn2O4的方法来制备λ-MnO2，并用X-射线衍射(XRD)、扫描电子显微镜(SEM)和恒电流充放电测试等方法对所得λ-MnO2的结构和电性能进行了研究。研究结果表明，所得λ-MnO2具有尖晶石型结构，晶粒细小，形貌较规则，粒径分布均匀；以其为正极组装成Li／MnO2电池的放电比容量达到226mAh/g。     

聚脲基脂及其在电机轴承上的应用

对电机轴承专用聚脲基脂的特点及其在电机轴承上的应用效果进行了分析和探讨。正确使用电机用润滑脂是保证电机正常工作，减少电机故障的关键措施之一。采用电机专用聚脲基脂后，电机轴承工作温度明显下降，电机故障率明显减少。     

尼龙6/改性双马来酰亚胺共混物的制备

将尼龙6与改性双马来酰亚胺熔融共混形成合金以提高其热稳定性能.用转矩流变仪考察了尼龙6/改性双马来酰亚胺共混体系熔融反应过程中的流变行为,用TG-DSC测试了共混物的热性能.结果表明:熔融共混时,2组分间的化学反应进行很快,改性双马来酰亚胺用量增加,共混物的熔融粘度增大,温度或转速升高,平衡转矩降低;改性双马来酰亚胺可明显改善尼龙6的高温热稳定性能,当尼龙6与改性双马来酰亚胺的质量比为20/1时,共混物在236-340℃温度范围内有很好的热稳定性.     

过程控制级模拟轧钢系统的研制及在热轧试车中的应用

宝钢集团上海第一钢铁有限公司(后面简称一钢)新建的不锈钢工程1780热轧项目中,为了能在较短周期内完成所有的应用软件开发与测试任务,特别研制了模拟轧钢功能。本论文主要阐述利用计算机的集成思想,结合热轧工艺,来开发模拟轧钢功能,以及利用模拟轧钢进行现场各种情况的模拟测试。     

Compatibility between Polyamide 6 and Polycarbonate

Polyamide （PA6） and polycarbonate （PC） were prepared by a Brabender mixer （ PLV- 151） at 240℃ with 30 rpm for duration of 8 and 6 minutes respectively. The epoxy resin （E） addition can lead to substantial microstructural changes in the PA6/PC blends. Scanning electron microscope （SEM） was used to observe the mixtures characterized by the domains of clearly segregated homophases and voids between the two polymers. PA6/PC of polyamide 6 and polycarbonate with epoxy resin addition under the composition ratio of 20/80, 20/80/1, 40/60/1 and 40/60, were tested to verify the key role of epoxy in promoting the compatibility of PA6 with PC during blending.     

Matlab软件在分形几何上的应用

以Koch曲线和塞尔平斯基三角形为例,介绍了Ma tlab软件在分形几何方面,对不规则图形进行直观描绘的方法。     

杀菌剂异螺环-4-烯-2,3-5''''-氯-吲哚的合成

研究了以薯蓣皂素(diosgenin)为原料,根据活性叠加原理,在分子中引入一个新的活性基团吲哚环,合成了全新化合物异螺环-4-烯-2,3-5'-氯-吲哚.杀菌药效试验结果表明:所设计的全新目标化合物具有原料所没有的杀菌活性.     

Design of the ECRH/ECCD Launcher System for HL-2A Tokamak

An ECRH/ECCD system with two 68GHz/500kW/1S gyrotrons will be built up in HL-2A tokamak. The location of the Gaussian beam waist is 580 mm away from the center of the plasmas and the beam radius is 37 mm at the center of the plasmas. Compared to the minor plasma radius （420 mm）, it is small enough for localized control. The launcher system covers a wide toroidal and poloidal steering range by the two steering plane mirrors. Therefore it is possible to explore the on- and off-axis heating over half of the plasma minor cross section and the co-current drive.