三螺杆挤出机常规螺纹元件挤出过程的CAE研究

利用ANSYS软件分析了三螺杆挤出机常规螺纹元件中等温非牛顿流体的压力场、速度场和粘度场，并和双螺杆挤出机常规螺纹元件进行了比较，尤其对流道中心区进行了重点研究。结果表明，三螺杆挤出机的混合性能好于双螺杆挤出机；中心区的物料压力梯度和速度梯度都较小，物料在中心区流动缓慢，中心区的物料粘度值较大；对反应时间不宜过长的聚合物，应避免使用三螺杆挤出机。     

Aerodynamic performance analysis of trains on slope topography under crosswinds

This work used the computational fluid dynamics method combined with full-scale train tests to analyze the train aerodynamic performance on special slope topography. Results show that with the increment in the slope gradient, the aerodynamic forces and moment increase sharply. Compared with the flat ground condition, the lateral force, lift force, and overturning moment of the train on the first line increase by 153.2%, 53.4% and 124.7%, respectively, under the slope gradient of 20°. However, with the increment of the windward side's depth, the windbreak effect is improved obviously. When the depth is equal to 10 m, compared with the 0 m, the lateral force, lift force and overturning moment of the train on the first line decrease by 70.9%, 77.0% and 70.6%,respectively. Through analyzing the influence of slope parameters on the aerodynamic performance of the train, the relationships among them are established. All these will provide a basic reference for enhancing train aerodynamic performances under different slope conditions and achieve reasonable train speeds for the operation safety in different wind environments.     

层间接触状态和横向力大小对车辙贡献率的影响

车辙贡献率是反映沥青路面各结构层车辙病害程度的一个主要参数,可用于指导沥青路面的设计和施工.利用三维有限元计算软件建立三维有限元模型用于理论分析,将有限元计算结果与理论解进行对比,验证了该三维有限元模型的可靠性.采用实测的轮胎接地压力,考虑不同层间接触状态和横向力大小,结合有限元计算的数据,分析了沥青路面结构层的车辙贡献率.结果表明:在层间完全连续状态下,横向力大小的选取不能简单地选取最大垂直轮胎接地压力的一定比例,而是要根据所研究的具体情况具体分析.在对沥青路面车辙贡献率的研究中,可以忽略层间接触状态,即假定层间完全连续.     

介质阻挡放电反应器降解邻二甲苯的特性研究

采用介质阻挡放电(DBD)降解常压下流动态的邻二甲苯模拟废气,系统地考察了放电极值电压,气体的初始质量浓度、停留时间以及相对湿度等工艺参数对邻二甲苯降解的影响,并初步探讨了邻二甲苯的降解产物.实验研究结果表明:在7.0kV的放电极间电压下,邻二甲苯的初始质量浓度为1 500mg/m3,停留时间为9s,其去除率可达到80%以上.降解产物主要为CO2、H2O以及苯甲酸、苯乙酸、苯乙醛等有机物,并且经降解后产物的生物可生化性得到提高,因而为后续的等离子-生物法联合处理VOCs提供了依据.     

中国信息服务业空间集聚研究

通过产业集聚的EG指数对中国各省份信息服务业的空间集聚程度进行研究,得出集聚程度比较显著.在此基础上,找到这一服务业的两个相关指标,利用产业集中度CRn判断出信息服务业主要集中于北京、广东等六个地区,然后对两指标数据进行无量纲化处理,加权求和得到新的综合指标,最后对这一新指标进行了系统聚类分析,得知这一产业主要集中在北京和广东两个地区.     

氧化鸡肉脂肪制备肉味香精前体物质的研究

研究以鸡肉脂肪为主要原料制备肉味香精的前体物质,通过单因素和正交试验确定氧化反应的最佳反应条件.结果表明氧化鸡肉脂肪的最佳条件是:氧化温度为120℃,氧化时间为3h,VE的添加量为1.0%,不添加水和NaCl.在最优条件下进行氧化试验,得到产物的酸值和过氧化值分别为1.472 mg/g和193.51 mmol/kg,感官评价值为4.905,具有典型特征的鸡肉香气.     

导磁体在汽车零件感应加热中的应用技术

本文简单介绍了导磁体工作的基本原理，并给出在汽车零件大规模生产中所积累的导磁体应用的一些经验，以阐明如何更有效地使用导磁体。     

Degradability and biocompatibility of bioglass/poly(amino acid) composites with different surface bioactivity as bone repair materials

Bioglass (BG) possesses excellent bioactivity and has been widely used in the manufacture of biomaterials. In this study, a composite with different surface bioactivity was fabricated via in situ melting polymerization by incorporating BG and poly(amino acid) (PAA) at a suitable ratio. The structure of the composite was characterized by Fourier transform infrared spectroscopy and XRD. The compressive strength of the BG/PAA composites was 139 MPa (BG:PAA = 30:70). The BG/PAA composites were degradable, and higher BG in composite showed higher weight loss after 4 weeks of incubation in simulated body fluid. In addition, the BG/PAA composite maintained adequate residual compressive strength during the degradation period. The SEM results showed the differences in surface bioactivities of the composites directly, and 30BG/PAA composite showed thicker apatite layer and higher Ca/p than 15BG/PAA. in vitro MG-63 cell culture experiments showed that the composite was noncytotoxic and thus allows cells to adhere, proliferate, and differentiate. This indicates that the composite has good biocompatibility. The implantations in the bone defects of rabbits for 4 and 12 weeks were studied. The composites had good biocompatibility and were capable of guiding new bone formation without causing any inflammation. The composite may be successfully used in the development of bone implants.     

Oxidation Performance of Fe-Al/WC Composite Coatings Produced by High Velocity Arc Sprayed at 650 ℃

Fe-Al intermetallics with remarkable high-temperatureintensity and excellent erosion,high-temperatureoxidation and sulfuration resistance are potential lowcost high-temperature structural material.ProducingFe-Al/WC composite coating by high velocity arcspraying(HVAS)on structural materials would notonly obviate the problems faced in fabrication of thesealloys into useful shapes,but also allow the effectiveuse of their outstanding high-temperature performance,which might thus promisingly mak…