Efficient PL Emission from p-type Porous Silicon: A Comparative Study for Selection of Effective Anodization Parameters

The physical mechanism of highly efficient photoluminescence (PL) emission from p-type silicon is described by a comparative study of the effectiveness of the etching parameters in an electrochemical anodization technique. Two series of porous silicon samples were prepared in a combination of anodization current and time, to maintain the total amount of anodic charge transfer constant. Photoluminescence studies show that irrespective of the amount of charge transfer, the samples prepared with comparatively higher current density show an efficient PL as well as stronger blueshift in the emission energy vis-à-vis the samples prepared for longer durations. An overall decrease in crystallite size, as estimated by Raman spectral analysis, was observed for both series of samples with the progress of charge transfer. Comparative analysis shows a marginal difference in crystallite size for both series of samples in the initial state of charge transfer, whereas major differences arise at higher values. This is explained with the formation of silicon suboxide on the porous surface at higher current density, leading to initiation of side wall reaction, and higher reduction rate in crystallite size as well as strong luminescence due to the carrier quantum confinement effect.     

Simulation of characteristics of double-junction solar cells based on ZnSiP2 heterostructures on silicon substrate

Design and operation modes of double-junction monolithic lattice-matched solar cells based on the ZnSiP₂/Si system of materials have been calculated. The effect of the photoactive region thickness and minority carrier lifetime in ZnSiP₂ layers on the efficiency of conversion of the incident solar light energy into electrical power was determined. It is shown that solar cells based on ZnSiP₂/Si heterostructures can provide efficiencies of 28.8% at AM1.5D, 100 mW/cm², and 33.3% at AM1.5D, 200 W/cm².     

Estimation of Limit Energy Characteristics of Volumetric Pneumatic Motors Taking into Account the Process Dynamics in Working Chambers

A methodology for estimation of the limit energy characteristics of volumetric pneumatic motors based on the Parameter Space Investigation method and a generalized mathematical model in dimensionless (normalized) form taking into account the dynamics of working processes is proposed. A calculated example is presented. The methodology is applicable for determination of the limit energy characteristics of newly created design solutions, of prospects to improve the known designs of pneumatic motors, of evaluation of energy capacity of several pneumatic motors supplied from a single source of compressed air, and of the initial data preparation for parametric synthesis of rotational pneumatic drives for two or more robots taking into account their interaction.     

Within-class multimodal classification

Multimedia Tools and Applications - In many real-world classification problems there exist multiple subclasses (or clusters) within a class; in other words, the underlying data distribution is...     

Microwave dielectric properties of ultra-low loss Li2MgTi0.7(Mg1/3Nb2/3)0.3O4 ceramics sintered at low temperature by LiF addition

In this work, ultra-low loss Li₂MgTi_0.7(Mg_1/3Nb_2/3)_0.3O₄ ceramics were successfully prepared via the conventional solid-state method. X-ray photoelectron spectroscopy (XPS), thermally stimulated depolarization current (TSDC) and bond energy were used to determine the distinction between intrinsic and extrinsic dielectric loss in (Mg_1/3Nb_2/3)⁴⁺ ions substituted ceramics. The addition of (Mg_1/3Nb_2/3)⁴⁺ ions enhances the bond energy in unit cell without changing the crystal structure of Li₂MgTiO₄, which results in high Q·f value as an intrinsic factor. The extrinsic factors such as porosity and grain size influence the dielectric loss at lower sintering temperature, while the oxygen vacancies play dominant role when the ceramics densified at 1400?°C. The Li₂MgTi_0.7(Mg_1/3Nb_2/3)_0.3O₄ ceramics sintered at 1400?°C can achieve an excellent combination of microwave dielectric properties: ε_r =?16.19, Q·f?=?160,000?GHz and τ_f =??3.14?ppm/°C. In addition, a certain amount of LiF can effectively lower the sintering temperature of the matrix, and the Li₂MgTi_0.7(Mg_1/3Nb_2/3)_0.3O₄-3?wt% LiF ceramics sintered at 1100?°C possess balanced properties with ε_r?=?16.32, Q·f?=?145,384?GHz and τ_f =??16.33?ppm/°C.     

Conveyer-belt accidents in mining and metallurgy

The dynamic interaction between the mechanical and electrical drive parameters when damage suddenly appears in the mechanical part of a conveyer belt is investigated. The possibility of using the change in the motor’s electrical parameters as a diagnostic signal is assessed. A model for investigating the dynamic processes in the system consisting of the grid, the induction motor, and the conveyer belt is proposed. The grid and induction motor are described by a model of fourth-order state space, whose output is the torque at the motor shaft. The moments of inertia and pliability of the links between the elements in the mechanical part of the conveyer belt are determined. By gradually identifying the elements with the minimum moment of inertia and distributing their moments of inertia and pliabilities among the adjacent elements, we obtain a three-mass system simulating the mechanical part of the conveyer belt. This dynamic model is solved by means of Matlab Simulink software. The energy characteristics of the drive are determined in dynamic processes following a mechanical accident.     

The reported point centromeres of Scheffersomyces stipitis are retrotransposon long terminal repeats

Point centromeres, found in some ascomycete yeasts such Saccharomyces cerevisiae, are very different in structure from the centromeres of other eukaryotes. They are tiny and nonrepetitive and contain only two short conserved sequence motifs. Until recently, point centromeres were thought to have a single evolutionary origin, in the budding yeast family Saccharomycetaceae. Most yeasts outside this family have centromeres that are many kilobases in size. Some have centromeres consisting of a large inverted repeat sequence, others have centromeric clusters of retrotransposons, and a third group including Candida albicans has centromeres with no conserved sequence features. It was recently reported that Scheffersomyces stipitis has point centromeres with a strongly conserved 125-bp core sequence, which is unexpected because S. stipitis is only distantly related to the known point-centromere species. We show here that the 125-bp core sequence is actually part of the long terminal repeat (LTR) of the Ty5-like retrotransposon Tps5, which forms a cluster in the centromeric region of each S. stipitis chromosome. Thus, the LTR of a centromere-associated retrotransposon confers centromere-like mitotic stability when cloned into a plasmid. The centromeric regions of S. stipitis contain three types of Tps5 element (Tps5a, Tps5b, and Tps5c) and a noncoding nonautonomous large retrotransposon derivative.     

Appraisal of Agriglass in Promoting Maize Production Under Abiotic Stress Conditions

An agriglass composition containing different oxides acts as a slow release for macro and micro nutrients and was chosen to improve maize yield under most important abiotic stresses which affecting agriculture development; salinity and drought. A field experiment was performed in salt affected soil (EC =?7.5 dSm^??1) by using different water deficit rates (I1 = 100, I2 = 85 and I3 = 70% of maize water requirements). Irrigation levels were located in main plots. Every main-plot divided into six sub-plots contained glassy fertilizer treatments [F1 = 55 kg fed^?1 with 1/2 mm diameter of agriglass (fed. =?4200 m²), F2 = 55 kg fed^?1 with 1 mm diameter, F3 = 80 kg fed^?1 with 1/2 mm diameter, F4 = 80 kg fed^?1 with 1 mm diameter, F5 = Recommendations of Ministry of Agriculture and F6 = control]. The experimental results demonstrated that, ears, straw, grains and biological yields increased with increasing both water and agriglass rates. Application of agriglass as a slow release fertilizer improved yield more than mineral fertilizer. Some growth parameters, water use efficiency (IWUE), macronutrients concentration and their relations were included. Other studies on residual effect of agriglass and the annual application rates to withstand salinity and drought stress by strategic crops are required.