Low-temperature poly-SiGe alloy growth of high gain/speed pin infrared photosensor with gold-induced lateral crystallization (Au-ILC)

The hydrogenated poly-silicon germanium (poly-SiGe:H) epitaxial film has been investigated using gold-induced lateral crystallization (Au-ILC) technology on a-SiGe:H layers at 10-h 350/spl deg/C annealing temperature and 60-sccm hydrogen (H/sub 2/) content. Using this optimal condition, the growth rate of the induced Au was as large as 15.9 /spl mu/m/h. With a low annealing temperature (/spl les/400/spl deg/C) and large growth rate, this novel technology will be noticeably useful for poly-SiGe:H pin IR-sensing fabrication on a conventional precoated indium tin oxide (ITO)-glass substrate. Under a 1-/spl mu/W IR-LED incident light (with peak wave length at 710 nm) and at a 5-V biased voltage, the poly-SiGe:H pin IR sensor developed by the Au-ILC technology, i.e., an Al (anode)/n poly-SiGe:H/i poly-SiGe:H/p poly-SiGe:H/ITO (cathode)/glass-substrate structure allowed for maximum optical gain and response speed. The optical gains and the response speeds were almost 600 and 130%, respectively, better than that of a traditional pin type. Meanwhile, the FWHM of a poly-SiGe:H pin sensor with Au-ILC technology was reduced from 280 to 150 nm. This reveals excellent IR-sensing selectivity. These IR-sensing trials demonstrated again that the proposed Au-ILC technology has very useful application in the field of low cost integrated circuits on optoelectronic applications.     

The Influence and Interpretation of Surface Parameters for Wetting Transitions in Ternary Mixtures

Starting from a microscopic Hamiltonian defined on a semi-infinite cubic lattice, and employing a mean-field approximation, the surface parameters relevant for wetting in confined ternary mixtures are derived. These are found in terms of the microscopic coupling constants, and yield a physical interpretation of their origins. In comparison with the standard expression for the surface free-energy density, several new terms arising from the derivation are identified. The influence of the surface parameters on a predicted unbinding transition in a mixture of oil, water, and amphiphile demonstrate that existing results are robust to the addition of the extra surface terms.     

A CMOS multichannel 10-Gb/s transceiver

We describe a CMOS multichannel transceiver that transmits and receives 10 Gb/s per channel over balanced copper media. The transceiver consists of two identical 10-Gb/s modules. Each module operates off a single 1.2-V supply and has a single 5-GHz phase-locked loop to supply a reference clock to two transmitter (Tx) channels and two receiver (Rx) channels. To track the input-signal phase, the Rx channel has a clock recovery unit (CRU), which uses a phase-interpolator-based timing generator and digital loop filter. The CRU can adjust the recovered clock phase with a resolution of 1.56 ps. Two sets of two-channel transceiver units were fabricated in 0.11-/spl mu/m CMOS on a single test chip. The transceiver unit size was 1.6 mm /spl times/ 2.6 mm. The Rx sensitivity was 120-mVp-p differential with a 70-ps phase margin for a common-mode voltage ranging from 0.6 to 1.0 V. The evaluated jitter tolerance curve met the OC-192 specification.     

High resistivity measurement of SiC wafers using different techniques

To establish fast, nondestructive, and inexpensive methods for resistivity measurements of SiC wafers, different resistivity-measurement techniques were tested for characterization of semi-insulating SiC wafers, namely, the four-point probe method with removable graphite contacts, the van der Pauw method with annealed metal and diffused contacts, the current-voltage (I-V) technique, and the contactless resistivity-measurement method. Comparison of different techniques is presented. The resistivity values of the semi-insulating SiC wafer measured using different techniques agree fairly well. As a result, application of removable graphite contacts is proposed for fast and nondestructive resistivity measurement of SiC wafers using the four-point probe method. High-temperature van der Pauw and room-temperature Hall characterization for the tested semi-insulating SiC wafer was also obtained and reported in this work.     

Metastable phase relation and phase equilibria in the Cr2O3-Fe2O3 system

In order to ascertain the metastable phase relation in the Cr₂O₃-Fe₂O₃ system, the existing phases were investigated by X-ray analysis using samples obtained by heating the coprecipitated powders for 1 h at 600–1000°C. There was a metastable two-phase region of Cr₂O₃-rich (CC) and Fe₂O₃-rich (FC) phases below about 940°C. Equilibrium state of 1:1 composition at 600–900°C was considered to be a single phase of the corundum solid solution. The metastable two-phase CC + FC region was suggested to appear probably due to the compositional inhomogeneity in the coprecipitated powders.     

Experimental characterisation of the drying effect on uniaxial mechanical behaviour of mortar

The main objective of this present study was to evaluate, for a standard mortar, the drying effect on its mechanical behaviour. Numerous uniaxial compression tests were thus performed with loading-unloading cycles. They were carried out on different samples previously preserved under various conditions of conservation: preserved from desiccation, air drying and rapid drying at 60°C. The obtained results showed significant influences of these conditions on the material behaviour (increase in strength, decrease in Young's modulus and Poisson's ratio) and the necessity of taking into account the coupling effects between mechanical—poromechanical behaviours and drying.     

Gamma-irradiation-induced Ag/SiO2 composite films and their optical absorption properties

Small Ag particles or clusters dispersed mesoporous SiO₂ composite films were prepared by a new method: First the matrix SiO₂ films were prepared by sol-gel process combined with the dip-coating technique, then they were soaked in AgNO₃ solutions followed by irradiation of γ-ray at room temperature and in ambient pressure. The structures of these films were examined by X-ray diffraction (XRD), high-resolution transmission electron microscope (HRTEM), and optical absorption spectroscopy. It has been shown that the Ag particles grown within the porous SiO₂ films are very small, and they are isolated and dispersed from each other with very narrow size distributions. With increasing the soaking concentration and an additional annealing, an opposite peakshift effect of the surface plasmon resonance (SPR) was observed in the optical absorption measurements.     

Analysis of the mechanism of die soldering in aluminum die casting

A mechanism of soldering of an aluminum alloy die casting to a steel die is proposed. A soldering critical temperature is postulated, at which iron begins to react with aluminum to form an aluminum-rich liquid phase and solid intermetallic compounds. The liquid joins the die with the casting upon solidification. The critical temperature is determined by the elements in both the casting alloy and the die material and is equal to the solidus temperature of the resulting alloy. The critical temperature is used to predict the onset of die soldering, and the local liquid fraction is related to the soldering tendency. Experiments have been carried out to validate the concept and to determine the critical temperature for die soldering in an iron-aluminum system. Thermodynamic calculations are used to determine the critical temperature and soldering tendency for the cases of pure aluminum and a 380 alloy in a steel mold. Factors affecting the soldering tendency are discussed, and methods for reducing die soldering are suggested.     

Super-multi-fibre PLC connector utilising angled connection between PLC and tens of fibres

A novel super-multi-fibre planar lightwave circuit (PLC) connector, designed to connect tens of optical fibres and a PLC for super-multichannel PLC-based optical modules with a receptacle interface, is proposed. This connector employs an angled connection instead of a PC connection. A 0.127 mm pitch 32-fibre connector is also demonstrated, which exhibits low connection and high return losses.