贝氏体钢内水冷穿孔顶头的粘钢及防止措施

从顶头生产工艺控制的角度,分析了贝氏体钢内水冷穿孔顶头产生粘钢的原因、特点和机制,指出掉鼻、缺肉是顶头粘钢的另一种更为严重的失效形式,强化熔炼工艺控制和保证夹杂物总量在A0.5B1C0.5D1级水平,粘钢问题可以得到有效控制。     

应用ATV71变频器有效解决给粉机变频器低电压跳闸问题

本文分析了给粉机变频器低电压跳闸的原因和解决办法，为解决给粉机变频器低电压跳闸，消除设备隐患提供了经验。     

高能超声处理Al-1Si合金凝固组织分析

采用高能超声处理Al-1Si合金熔体,借助金相显微镜和电子探针进行组织分析,并测定合金的熔化潜热,分析了熔体中超声空化效应和声流效应影响凝固过程的机理。结果表明,试样晶粒平均尺寸由超声处理前的94μm减小到超声处理后的34μm;合金试样的熔化吸热量由263.90J/g降低为159.81J/g,在熔体中施加高能超声显著改善了合金成分的均匀性并细化了晶粒。     

The transformation of aluminium species in the processes of coagulation, sedimentation and filtration.

The aluminium toxicity is closely related to aluminium species. In this work aluminium was fractionated into seven forms: Al(T), Al(Sus), Al(C + S), Al(S), Al(C), Al(O) and Al(I). Four Al-based coagulants and simulated raw water were used in the laboratory to investigate the aluminium transformation in coagulation, sedimentation and filtration processes. It is the use of Al-based coagulants that contributes more to the increase of the residual aluminium for the low-turbidity raw water, while the Al-based coagulants, especially the polymeric aluminium coagulants, work to remove the aluminium from the high-turbidity raw water. In the case of traditional coagulants, the increase of the turbidity or the dissolved organic carbon (DOC) concentration in the raw water results in a high concentration of Al(C + S). The removal rate of aluminium species in the filtration process is not only related to its size: RAl(Sus) > RAl(C+S), RAl(C) > RAl(S), but also to the physicochemical properties of aluminium species and filter. For the kaolin-polyaluminium chloride system, a lower removal rate of aluminium species results is due to the complexation of humic acid and aluminium species.     

热电厂锅炉运行技术指标的微机管理

本文从锅炉运行技术指标台帐微机管理的实际出发，提出了热量计算中主蒸汽流量修正系数Ｃ和给水焓值Ｚ两项参数回归的计算公式，提高了热量计算数值精度。     

纺织品印染后整理剂Fs的研制

纺织品印染后整理剂Fs系多羟基多胺的阳离子树脂型缩合物,不含游离甲醛。本文介绍了纺织品印染后整理剂Fs的合成方法和应用条件。     

含油废水处理

在水量水质调查的基础上，本文提出了以出水回用为目的的含油废水隔油调节沉淀－混凝沉淀－砂滤处理工艺，动态模型试验表明，废水中油和ＣＯＤ的去除率分别达到９５％和９０％，出水浊度低于２，此水质完全可回用于有关生产车间。