Thermal conductivity of bulk ZnO after different thermal treatments

Thermal conductivities (κ) of melt-grown bulk ZnO samples thermally treated under different conditions were measured using scanning thermal microscopy. Samples annealed in air at 1050°C for 3 h and treated with N-plasma at 750°C for 1 min. exhibited κ=1.35±0.08 W/cm-K and κ=1.47±0.08 W/cm-K, respectively. These are the highest values reported for ZnO. Atomic force microscopy (AFM) and conductive-AFM measurements revealed that surface carrier concentration as well as surface morphology affected the thermal conductivity.     

On Multiple Scattering of Radiation by an Infinite Grating of Dielectric Circular Cylinders at Oblique Incidence

A rigorous analytical representation for the multiple scattering coefficients of the fields radiated by an infinite grating of dielectric circular cylinders excited by an obliquely incident plane electromagnetic wave is derived in terms of the “well-known scattering coefficients of an isolated dielectric cylinder at oblique incidence” and “Schlömilch series”. In addition, a generalized sum-integral grating equation is acquired for the multiple scattered amplitude of a cylinder at oblique incidence in the grating in terms of the scattering coefficients of the insulating dielectric circular cylinder at oblique incidence.     

The forward bias current density–voltage–temperature (J–V–T) characteristics of Al–SiO2–pSi (MIS) Schottky diodes

Metal–insulator–semiconductor Schottky diodes were fabricated to investigate the tunnel effect and the dominant carrier transport mechanism by using current density–voltage (J–V) and capacitance–voltage (C–V) measurements in the temperature range of 295–370?K. The slope of the ln?J–V curves was almost constant value over the nearly four decades of current and the forward bias current density J is found to be proportional to J_o (T) exp(AV). The values of N_ss estimated from J–V and C–V measurements decreased with increasing temperature. The temperature dependence of the barrier heights obtained from forward bias J–V was found to be entirely different than that from the reverse bias C–V characteristics. All these behaviours confirmed that the prepared samples have a tunnel effect and the current transport mechanism in the temperature range of 295–370?K was predominated by a trap-assisted multi-step tunnelling, although the Si wafer has low doping concentration and the measurements were made at moderate temperature.     

High output impedance current-mode lowpass,bandpass and highpass filters using current controlled conveyors

Three new current-mode second-order filter configurations which employ one or two current controlled conveyors (CCCIIs) and three passive elements are presented. Each proposed filter can realize one of the bandpass, lowpass or highpass responses all at high impedance outputs. The proposed filters offer current-control of pole angular frequency ω_o without disturbing the parameter ω_o /Q. No component matching is required and all the passive and active sensitivities are low. PSPICE simulation results are given to confirm the theoretical analysis.     

Wind turbine speed control of a contactless piezoelectric wind energy harvester

ABSTRACT

Wind turbine control is an important task to make the electricity generation secure in terms of energy demand and machine safety. It also yields to control the desired power level and optimized energy because of the assignment of turbine speed. The contactless piezoelectric wind energy harvester (CPWEH) used in this study has three piezoelectric layers located around the shaft with 120 degrees apart and they are buckled by the magnetic force without any physical contact. The superiority of this device is to generate energy for low wind speeds such as 1.5 m/s. However, for high speeds, high total harmonic distortions (THDs) govern the waveforms, thus controlling the turbine speed becomes necessary for optimizing the output power. Encouraged by this, a small low inertia dc generator is coupled with the wind turbine, and the generator terminals are connected to a resistor through a power switch to generate a braking torque that opposes to wind speed direction. By controlling the switch properly, turbine speed is ensured to remain within a certain band, which accordingly prevents the turbine from rotating very fast at damaging wind speeds. Several experiments are performed on the developed CPWEH with/without the presented control scheme which prove the existence of promising performance of our proposal.     

A design method for substrate integrated waveguide electromagnetic bandgap (SIW-EBG) filters

An efficient design method for substrate integrated waveguide electromagnetic bandgap (SIW-EBG) filters is proposed which provides direct dimensional synthesis approach for desired filter objectives without using network representations. The method is applied to the design of an X band SIW-EBG filter and its response is compared with HFSS (high frequency structure simulator) simulations for validation purposes. Fairly good agreement between the results shows the applicability of the proposed method for SIW-EBG filter design.     

Mode competition using TE03 gyrotron cavities

The gyrotron is a powerful source of millimetre wave radiation. Fusion applications require more power per tube than is currently available This in turn means that the resonator must be highly overmoded, with a dense mode spectrum, which leads to mode competition. The influence of external parameters, such as the applied magnetic field, electron beam, and resonator geometry, on mode competition in tubes designed to operate at 150 and 140 GHz in the TE⁰³ mode is investigated theoretically and experimentally. It can be shown that even when the mode spectrum is fairly dense, single mode operation of a gyrotron is possible. The influence of startup conditions on output power is investigated in the 150 GHz experiment. In some cases, modes with an axial index of 2 were excited.     

Design of practical broadband matching networks with commensurate transmission lines

To design broadband matching networks for microwave communication systems, commercially available computer aided design (CAD) tools are always preferred. But these tools need proper matching network topology and element values. Therefore, in this paper, a practical method is proposed to generate distributed-element matching networks with good initial element values. Then, the gain performance of the designed matching network can be optimized employing these tools. The utilization of the proposed method is illustrated by means of the given example. It is shown that proposed method provides very good initials for CAD tools.     

Cellulose‐Based Ionogels for Paper Electronics

A new class of biofriendly ionogels produced by gelation of microcellulose thin films with tailored 1‐ethyl‐3‐methylimidazolium methylphosphonate ionic liquids are demonstrated. The cellulose ionogels show promising properties for application in flexible electronics, such as transparency, flexibility, transferability, and high specific capacitances of 5 to 15 μF cm^?2. They can be laminated onto any substrate such as multilayer‐coated paper and act as high capacitance dielectrics for inorganic (spray‐coated ZnO and colloidal ZnO nanorods) and organic (poly[3‐hexylthiophene], P3HT) electrolyte‐gated field‐effect transistors (FETs), that operate at very low voltages (<2 V). Field‐effect mobilities in ionogel‐gated spray‐coated ZnO FETs reach 75 cm² V^?1 s^?1 and a typical increase of mobility with decreasing specific capacitance of the ionogel is observed. Solution‐processed, colloidal ZnO nanorods and laminated cellulose ionogels enable the fabrication of the first electrolyte‐gated, flexible circuits on paper, which operate at bending radii down to 1.1 mm.     

Verteilte Flickermessungen in Windparks

Wind power stations in windfarms connected to the power system can disturb the power quality. Effects like pole-reconnections, shadowing-effects as well as wind squalls will result in power fluctuations. So voltage fluctuations and flicker effects will occur. We present results of field measurements, carried out on windfarms in Germany in April 1998.