Fracture behavior of glass bead-filled poly(oxymethylene) injection moldings

The mechanical properties of glass bead filled poly(oxymethylene) were investigated as a function of glass bead content and glass bead diameter using injection molded test pieces. Fracture toughness measurements were made using single edge-notched tension and single edge-notched bend specimens. The effect of notch orientation with respect to the mold fill direction on fracture toughness was studied using single gate and double gate moldings. Tensile strength and flexural modulus were measured using standard test pieces. It was found that; (i) fracture toughness of the filled and unfilled polymer was relatively independent of notch orientation, (ii) the presence of weldlines in the molded test pieces did not affect the fracture toughness of unfilled polymer or its composites, (iii) fracture toughness of filled polymer was always considerably lower than that of the unfilled polymer; fracture toughness decreased sharply with increasing bead concentration, (iv) fracture toughness was not a sensitive function of glass bead diameter; it decreased slightly as bead diameter increased, (v) strain energy release rate as measured under impact decreased with increasing bead concentration, (vi) tensile strength decreased linearly with increasing glass bead concentration and was inversely proportional to the square root of the bead diameter, (vii) weldlines did not affect the tensile strength of the polymer or its composities, (viii) flexural modulus increased linearly with increasing glass bead concentration according to the Einstein equation.     

Poly(azomethine-imide)s containing siloxane moities: Optical,thermal, mechanical,and morphological properties

A new series of poly(azomethine-imide)s having siloxane moities in backbone was prepared using different dianhydrides.Thermal, optical, and morphological properties of these polymers were clarified. Also, bulky  CO and  CF₃ group effects and meta or para-substituted aldeyhde effects on the mentioned properties were evaluated. The structural characterization of poly(azomethine-imide)s was carried out using a FT-IR spectroscopy. The optical properties of the polymers were performed via an UV–Vis spectrophotometer. Optical band gap of the poly(imide)s containing azomethine was calculated between 2.20 and 2.33 eV. Thermal behavior of poly(azomethine-imide)s was also studied using TG-DTA, DSC, and DMA techniques. The onset degradation temperature and percentage char values of the polyimides were found in the range from 429 to 545 °C and 22 to 35%, respectively. Thermal stability results demonstrated that benzophenone bearing poly(azomethine-imide)s have higher onset temperature, percentage char, and the glass transition temperature than poly(azomethine-imide)s derived from hexafluoroisopropylidene. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2020 , 137, 48364.     

Studies on batch adsorptive removal of cadmium and nickel from synthetic waste water using silty clay originated from Balochistan–Pakistan

The potentials of silty clay(SC), acquired from Chaman, Balochistan, were investigated as adsorbent for Ni(Ⅱ)and Cd(Ⅱ) removal from contaminated media. The influence of different operating factors like dose, pH, temperature, and time of contact was explored, and optimum values were noted under batch adsorption method. Isothermal study was conducted with varying concentrations of solutions on optimized conditions and different adsorption models i.e., Langmuir, Freundlich, Temkin and Dubinin–Radushkevich(D–R) isotherm, which were employed to interpret the process. The isothermal data of both Ni(Ⅱ) and Cd(Ⅱ) were well fitted to Langmuir isotherm suggesting the formation of monolayer of metal ions on silty clay. The values of adsorption capacity noted for Ni(Ⅱ) and Cd(Ⅱ) were 3.603 mg·g~(-1) and 5.480 mg·g~(-)1, respectively. Kinetic studies affirmed that pseudo second order(PSO) kinetics was being obeyed by the removal of Ni(Ⅱ) and Cd(Ⅱ). Thermodynamic variables like free energy change(ΔG°), enthalpy change(ΔH°) and entropy change(ΔS°) were calculated. The negative value of ΔG° and the positive values of ΔH° and ΔS° unfolded that the removal process of both metal ions of by SC was spontaneous, endothermic and feasible.     

黑釉铁锈花产品的试制

本文论述了黑釉铁锈花产品的坯釉料组成及制作工艺．井对黑釉铁锈花产品的起源、形成机理进行了探讨分析。     

The Effects of Heat Treatment on Some Mechanical Properties of Juvenile Wood and Mature Wood of Eucalyptus grandis

Heat treatment is a well-known method for modifying wood that is applied in different ways, and treatment schedules change from tree to tree. This treatment improves the physical properties of wood but, in general, it reduces the mechanical properties of wood. The effects of heat treatment on the mechanical properties of juvenile and mature wood of the same tree species have not been well-defined. Therefore, we focused our study on the differences in the mechanical properties of juvenile wood and mature wood of Eucalyptus grandis after both were subjected to heat treatment. Wood samples were treated at temperatures of 120, 150, and 180°C for 4, 6, and 8 h. The test results showed that decreases in the mechanical properties of juvenile wood (e.g., modulus of elasticity (MOE), modulus of rupture (MOR), compression strength (CS), and impact bending (IB)) were greater than the decreases that occurred in mature wood that was heat treated at the same conditions.     

Radiation crosslinking and sorption properties of hydrogels based on 1‐vinyl‐2‐pyrrolidone,hydroxyethyl methacrylate,and their copolymers

This work has been concerned with the synthesis of the hydrogels of poly (vinyl pyrrolidone) (NVP), poly (hydroxy ethylmethacrylate) (HEMA), and their copolymer under the effect of gamma radiation in the presence of N,N‐methylenebisacryl‐amide (MBAm) as a crosslinking agent. The effect of the different factors that may affect the gelation and yield product, such as solvent composition and irradiation dose, was investigated. The formed hydrogels were characterized in terms of swelling in water and different organic solvents, X‐ray diffraction (XRD), and IR spectroscopic analysis. The sorption capability of these hydrogels towards some commercial basic and acid dyesstuffs was also studied. The results showed that a solvent mixture composed of equal contents of water and methanol is the most suitable to afford the minimum sol fraction and the highest yield product at a minimal irradiation dose of 10 kGy. It was observed that NVP hydrogel displayed the highest swelling in water, alcohols, and dimethyformamide of ～1300% and a lower tendency to swell in nonpolar solvents. The results showed that HEMA hydrogel has a high affinity to absorb basic dyes while NVP has a tendency for acid dyes. Also, the sorption of either the basic or acid dyes by the different hydrogels was found to greatly depend on the concentration of dye in solution and the mass of the used hydrogel. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 91: 3274–3280, 2004     

Competitive adsorption of uranyl ions in the presence of Pb(II) and Cd(II) ions by poly(glycidyl methacrylate) microbeads carrying amidoxime groups and polarographic determination

The adsorption capacity of UO in the presence of Pb(II) and Cd(II) ions was investigated with amidoximated poly(glycidyl methacrylate) (PGMA) microbeads with an average size of 135 μm packed in a glass column (0.5‐cm i.d. and 20‐cm length, flow rate = 3 mL/min) under competitive conditions. A differential pulse polarography technique was used for the determination of trace quantities of uptaken elements by the measurement of the reduction peak currents at ?200/?950, ?400, and ?600 mV (vs a saturated calomel electrode) for UO, Pb(II), and Cd(II) ions, respectively. When only UO was found in the eluate, its adsorption was 85.3% from a 50 μM initial solution. However, when there was UO with binary systems of Pb(II) or Cd(II), it was 78.2 and 76.3%, respectively. On the other hand, in a ternary mixture of UO with Pb(II) and Cd(II), the adsorption was found to be 75.2% with the same initial concentration. According to the results, the competitive adsorption studies showed that these amidoximated PGMA microbeads had good adsorption selectivity for UO with the coexistence of Pb(II) and Cd(II) ions. The ionic strength of the solution also influenced the UO adsorption capacity of the amidoximated PGMA microbeads. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 104: 4168–4172, 2007     

Synthesis and Characterization of Cationic Surfactants Based on N‐Hexamethylenetetramine as Active Microfouling Agents

Four cationic surfactants of quaternary hexammonium silane chloride based on hexamethylenetetramine and alkyl chloride were synthesized. The chemical structures of the prepared cationic surfactants were elucidated using Fourier transform infrared (FT‐IR) spectroscopy and mass spectrometry analysis. The surface and thermodynamic properties of the prepared surfactants were also studied. The performance of these cationic surfactants as microfouling agents against two strains of Gram‐negative bacteria, namely, Pseudomonas aeruginosa and Escherichia coli, and two strains of Gram‐positive bacteria, namely, Staphylococcus aureus and Bacillus subtilis, were evaluated as antimicrobial agents. The results showed that the maximum antimicrobial activity was detected for N‐hexamethylenetetramine‐N‐ethyl silane ammonium trichloride (Ah). The maximum and minimum antimicrobial activities were 73 and 60 % against S. aureus and E. coli, respectively, at a concentration of 5 mg/l, pH 7, and 37 °C.     

Effects of use of higher strength interlayer and external cooling on properties of friction stir welded AA6061-T6 joints

Although sound AA6061-T6 joints can be produced by friction stir welding, a loss in strength takes place in the weld region. In this study, it was demonstrated that the strength of the nugget could be increased by the use of a higher strength interlayer during friction stir welding. This strength recovery cannot, however, be attainable in the heat affected zone. Although an external cooling was applied during welding in order to increase strength in the heat affected zone, it was not sufficient for achieving the required cooling condition for improved strength.