Evaluation of rheological and image properties of styrene‐butadiene‐styrene and ethylene‐vinyl acetate polymer modified bitumens

This article presents a laboratory evaluation of conventional, fundamental, rheological, and morphological characteristics of styrene‐butadiene‐styrene (SBS) and ethylene vinyl acetate (EVA) polymer modified bitumens. Polymer modified bitumen (PMB) samples have been produced by mixing a 50/70 penetration grade unmodified (base) bitumen with SBS and EVA copolymer at different polymer contents. The fundamental viscoelastic properties of the PMBs were determined using dynamic (oscillatory) mechanical analysis and presented in the form of temperature and frequency‐dependent rheological parameters. The morphology of the samples as well as the percent area distribution of polymers throughout the base bitumen have been characterized and determined by means of fluorescent light optic microscopy and Qwin Plus image analysis software, respectively. The results indicated that polymer modification improved the conventional and rheological properties of the base bitumen. It was also concluded that the temperature and frequency had a significant effect on complex modulus of PMBs. The behavior of EVA and SBS PMBs had exhibited quite difference at 50°C. Moreover, it was found out that at low polymer contents, the samples revealed the existence of dispersed polymer particles in a continuous bitumen phase, whereas at high polymer contents a continuous polymer phase has been observed. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Vinyl triazole carrying metal‐chelated beads for the reversible immobilization of glucoamylase

Poly(ethylene glycol dimethacrylate–1‐vinyl‐1,2,4‐triazole) [poly(EGDMA–VTAZ)] beads with an average diameter of 100–200 μm were obtained by the copolymerization of ethylene glycol dimethacrylate (EGDMA) with 1‐vinyl‐1,2,4‐triazole (VTAZ). The copolymer hydrogel bead composition was determined by elemental analysis and was found to contain 5 EGDMA monomer units for each VTAZ monomer unit. The poly(EGDMA–VTAZ) beads were characterized by swelling studies and scanning electron microscopy (SEM). The specific surface area of the poly(EGDMA–VTAZ) beads was found 65.8 m²/g. Cu²⁺ ions were chelated on the poly(EGDMA–VTAZ) beads. The Cu²⁺ loading was 82.6 μmol/g of support. Cu²⁺‐chelated poly(EGDMA–VTAZ) beads with a swelling ratio of 84% were used in the immobilization of Aspergillus niger glucoamylase in a batch system. The maximum glucoamylase adsorption capacity of the poly(EGDMA–VTAZ)–Cu²⁺ beads was 104 mg/g at pH 6.5. The adsorption isotherm of the poly(EGDMA–VTAZ)–Cu²⁺ beads fitted well with the Langmuir model. Adsorption kinetics data were tested with pseudo‐first‐ and second‐order models. The kinetic studies showed that the adsorption followed a pseudo‐second‐order reaction model. The Michaelis constant value for the immobilized glucoamylase (1.15 mg/mL) was higher than that for free glucoamylase (1.00 mg/mL). The maximum initial rate of the reaction values were 42.9 U/mg for the free enzyme and 33.3 U/mg for the immobilized enzyme. The optimum temperature for the immobilized preparation of poly(EGDMA–VTAZ)–Cu²⁺–glucoamylase was 65°C; this was 5°C higher than that of the free enzyme at 60°C. The glucoamylase adsorption capacity and adsorbed enzyme activity slightly decreased after 10 batch successive reactions; this demonstrated the usefulness of the enzyme‐loaded beads in biocatalytic applications. The storage stability was found to increase with immobilization. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Metallo‐supramolecular materials based on terpyridine‐functionalized polyhedral silsesquioxane

In this study, novel metallo‐supramolecular materials based on terpyridine‐functionalized polyhedral silsesquioxane were synthesized from 4′‐chloro‐2,2′:6′,2″‐terpyridine and amino‐group‐functionalized polyhedral oligomeric silsesquioxane. The obtained terpyridine‐functionalized polyhedral silsesquioxanes were converted to metallo‐supramolecular hybrid materials by coordination polycondensation reaction with Co(II) or Cu(II) ions. The supramolecular polymers created were characterized by means of structure, morphology and stimuli‐responsive performance employing scanning electron microscopy, amperometric techniques and UV–visible and Fourier transform IR spectroscopy. UV?visible and cyclic voltammetry studies showed that both the optical and electrochemical properties of metallo‐supramolecular materials are affected by the substituent at the pyridine periphery. The supramolecular polymers obtained exhibited electrochromism during the oxidation processes of cyclic voltammogram studies. As a result, these terpyridine‐functionalized polyhedral silsesquioxanes are good candidates for electronic, opto‐electronic and photovoltaic applications as smart stimuli‐responsive materials. © 2013 Society of Chemical Industry     

Polymerization of epoxides catalyzed by a mixed‐valent iron trifluoroacetate [Fe3O(O2CCF3)6(H2O)3]

The readily available mixed‐valent iron trifluoroacetate complex [Fe₂^IIIFe^II(µ₃‐O)(O₂CCF₃)₆(H₂O)₃] is an effective catalyst for the polymerization of epoxides. A very small amount of the catalyst (1.0–0.01 mol%) could initiate the polymerization of cyclohexene oxide, cyclopentene oxide and epichlorohydrin. Based on quantitative end‐group analysis by ¹⁹F NMR spectroscopy, a Lewis acid (LA^⊕) catalyzed anionic reaction mechanism is proposed. Copyright © 2012 Society of Chemical Industry     

Preparation of Gadolina Stabilized Bismuth Oxide Doped with Boron via Electrospinning Technique

In this study, boron doped and undoped poly (vinyl) alcohol/bismuth–gadolina acetate (PVA/Bi–Gd) nanofibers were prepared using electrospinning technique then calcinated at 800 °C for 2 h. The originality of this study is the addition of boron to metal acetates. The effects of boron doping were investigated in terms of solution properties, morphological changes and thermal characteristics. The characteristics of the fibers were investigated with FT-IR, XRD, SEM and BET. The addition of boron did not only increase the thermal stability of the fibers, but also their diameters, which yielded stronger fibers. XRD analyses showed that boron doping increased the peak intensities and indicated that the boron doping enhanced the crystallite size. Moreover, no shifts were noticed in diffraction angles for boron doped and undoped samples. Therefore, boron doping did not significantly alter the lattice spacing. The SEM micrograph of the fibers showed that the addition of boron resulted in the formation of cross-linked bright-surfaced fibers. The average fiber diameter for boron doped and undoped fiber mats were 204 and 123 nm, respectively. Also, grain diameters of boron doped and undoped nanocrystalline sintered powders were measured as 140 and 118 nm, respectively. The BET results showed that boron undoped and doped Bi₂O₃–La₂O₃ nanocrystalline powder ceramic structures sintered at 800 °C have surface areas of 59.72 and 39.80 m²/g, respectively.     

In vacuo production of α-AlB12, C4AlB24, AlB12C2 and Al3B48C2 powders

The production of pure powder samples of boron-rich ternary Al–B–C phases was investigated in vacuum at temperatures between 1400 °C and 1600 °C, using a range of different starting powders. Compacted powder mixes of B–AlB₂–B₄C, Al–B–C, Al–B–B₄C, B–C–AlB₂, B–AlB₂ and Al–B were heated for 1–2 h under vacuum in a carbon resistance furnace and the products characterised by X-ray diffraction. It was found impossible to produce significant quantities of C₄AlB₂₄ under these conditions, but >95% pure samples of α-AlB₁₂, AlB₁₂C₂ and Al₃B₄₈C₂ were obtained. This study is a precursor to further research aimed at producing dense B₄C-type materials which might offer the advantages of easier densification and fabrication as compared with B₄C itself.     

Thermal energy storage by poly(styrene-co-p-stearoylstyrene) copolymers produced by the modification of polystyrene

A series of poly(styrene-co-p-stearoyl styrene) copolymers as novel polymeric solid–solid phase-change materials (SSPCMs) were synthesized by the modification of polystyrene with stearoyl chloride. The chemical structure and crystalline morphology of the synthesized copolymers were determined with Fourier transform infrared spectroscopy and polarized optical microscopy, respectively. The thermal energy storage properties and thermal stability of the SSPCMs were investigated with differential scanning calorimetry and thermogravimetric analysis, respectively. In addition, the thermal conductivity of the SSPCMs was measured with a thermal property analyzer. Moreover, thermal cycling tests showed that the copolymers had good thermal reliability and chemical stability after being subjected to 5000 heating/cooling cycles. The synthesized poly(styrene-co-stearoyl styrene) copolymers as novel SSPCMs have considerable potential for thermal energy storage and temperature-control applications. © 2012 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Selective separation of cobalt and nickel by flat sheet supported liquid membrane using Alamine 300 as carrier

Cobalt and nickel are among the most important nonferrous metals. The using of flat sheet supported liquid membranes (FSSLMs) to remove metals from wastewaters has been used actively by the scientific and industrial communities. In this study, the selective separation of cobalt from thiocyanate solutions containing cobalt and nickel by FSSLM was examined using tri-n-octylamine (Alamine 300) as carrier. The FSSLM was consisted of extractant, flat sheet support and organic solvent. The various parameters were studied to determine the optimum extraction and striping conditions of cobalt and nickel. These parameters were stirring speeds of phases, NH₄SCN concentration, pH, diluent type, extractant concentration, stripping reagent concentration and modifier concentration. Concentration of cobalt and nickel were determined by Shimadzu AA-6701GF spectrophotometer. In the optimum conditions, selective separation of cobalt was achieved with an efficiency of 98.4% within 8 h, for equimolar feed mixtures, 400 mg/L Co + 400 mg/L Ni, and the separation factor of Co(II) over Ni(II) was 234.4. In addition, for nonequimolar feed mixtures, 500 mg/L Co + 1000 mg/L Ni, Ni in excess, selective separation of cobalt was 99.9%, and the separation factor of Co was 506 in the same time.     

Flexible poly(styrene-ethylene-butadiene-styrene) hybrid nanofibers for bioengineering and water filtration applications

Among the thermoplastic elastomers that play important roles in the polymer industry due to their superior properties, styrene-based species and polyurethane block copolymers are of great interest. Poly(styrene-ethylene-butadiene-styrene) (SEBS) as a triblock copolymer seems to have the potential to meet many demands in different applications due to various industrial requirements where durability, biocompatibility, breaking elongation, and interfacial adhesion are important. In this study, the SEBS triblock copolymer was functionalized with natural (Satureja hortensis, SH) and synthetic (nanopowder, TiO₂) agents to obtain composite nanofibers by electrospinning and electrospraying methods for use in biomedical and water filtration applications. The results were compared with thermoplastic polyurethane (TPU) composite nanofibers, which are commonly used in these fields. Here, functionalized SEBS nanofibers exhibited antibacterial effect while at the same time improving cell viability. In addition, because of successful water filtration by using the SEBS composite nanofibers, the material may have a good potential to be used comparably to TPU for the application.