A Study of Mutual Coupling between Vertical Grounding Electrodes

This paper investigates the mutual grounding impedance between vertical grounding electrodes based on field measurements and FDTD simulations. In the case of vertical electrodes, the mutual impedance between the electrodes is almost completely independent of the electrode length, and thus the induced voltage is nearly constant as the electrode length becomes longer. This characteristic is different from that of an overhead conductor, where the electromagnetic‐induced voltage is proportional to the conductor length. The greater the separation distance between the electrodes, the smaller the induced voltage, as in the case of an overhead conductor. The propagation speed increases as the separation increases. It is found that the speed is not necessarily proportional to the inverse of the relative permittivity of the earth.     

Effect of evaporation time on the pervaporation characteristics through homogeneous aromatic polyamide membranes. II. Pervaporation performances for ethanol/water mixture

Pervaporation of ethanol/water mixtures through symmetric dense aromatic polyamide membranes was investigated. The membrane structure was controlled by varying the solvent evaporation time before gelation. The membranes were water-selective and the selectivity increased with an increase in the solvent evaporation time. On the other hand, the water flux as well as the ethanol flux decreased with an increase in the evaporation time. These results were consistent with the morphology change of the membrane which takes place with solvent evaporation: the decrease in the channel size. The effects of the downstream pressure on the pervaporation performances were also studied for membranes with different solvent evaporation times. the ethanol concentration in the permeate side increased with an increase in the downstream pressure to certain point, showed a maximum there, then decreased thereafter. The water flux decreased with an increase in the downstream pressure for all membranes studied; the dependence was expressed by a parabolic curve in the lower pressure range. The ethanol flux also decreased with an increase in the downstream pressure for the membrane with shorter evaporation time, while this flux was slightly affected by the downstream pressure for the membrane with longer evaporation time. © 1996 John Wiley & Sons, Inc.     

Preparation of high-modulus poly(ethylene terephthalate) fibers by vibrating hot drawing

A novel drawing method, vibrating hot drawing, was successfully applied to poly(ethylene terephthalate) fiber, which has a normal molecular weight (IV = 0.7 dL/g) and was prepared by melt spinning. The process was divided into three steps, with differing conditions in drawing temperature, applied tension, vibrating frequency, and amplitude. The drawing temperature and vibration frequency were decided by considering the α_a dispersion of the polymer. In spite of a low draw ratio (7.7) and a low crystallinity (0.55), the birefringence and dynamic storage modulus at room temperature of the 3rd-step fiber reached 0.260 and 36 GPa, respectively. The modulus remains at a high level at elevated temperatures, for example, 29 GPa at 100°C and 17 GPa at 200°C. Further, it was found from temperature and intensity of the α_a dispersion peak that the movements of amorphous chains are strongly inhibited. © 1996 John Wiley & Sons, Inc.     

Influence of Tip Clearance on Blade Vibration of Vaneless Radial Turbine

With the increasing demand of turbochargers with high performance and low turbo lag, high cycle fatigue (HCF) of radial turbine blades has become the most commo...     

Structural and Functional Change in Albino Rat Retina Induced by Various Visible Light Wavelengths

The effects of visible light, from short to long wavelengths, on the retina were investigated functionally and histologically. The left eyes of Sprague–Dawley albino rats (6-weeks old, n = 6 for each wavelength) were exposed to seven narrow-band wavelengths (central wavelengths, 421, 441, 459, 501, 541, 581, and 615 nm) with bandwidths of 16 to 29 nm (half bandwidth, ±8–14.5 nm) using a xenon lamp source with bandpass filters at the retinal radiant exposures of 340 and 680 J/cm². The right unexposed eyes served as controls. Seven days after exposure, flash electroretinograms (ERGs) were recorded, and the outer nuclear layer (ONL) thickness was measured. Compared to the unexposed eyes, significant reductions in the a- and b-wave ERG amplitudes were seen in eyes exposed to 460-nm or shorter wavelengths of light. The ONL thickness near the optic nerve head also tended to decrease with exposure to shorter wavelengths. The decreased ERG amplitudes and ONL thicknesses were most prominent in eyes exposed to 420-nm light at both radiant exposures. When the wavelengths were the same, the higher the amount of radiant exposure and the stronger the damage. Compared to the unexposed eyes, the a- and b-waves did not decrease significantly in eyes exposed to 500-nm or longer wavelength light. The results indicate that the retinal damage induced by visible light observed in albino rats depends on the wavelength and energy level of the exposed light.     

Corrosion characteristics of reduced activation ferritic steel, JLF-1 (8.92Cr–2W) in molten salts Flibe and Flinak

Static corrosion tests were performed in molten salts, LiF–BeF₂ (Flibe) and LiF–NaF–KF (Flinak), at 500 °C and 600 °C for 1000 h. The purpose is to investigate the corrosion characteristics of reduced activation ferritic steels, JLF-1 (8.92Cr–2W) in the fluids. The concentration of hydrogen fluoride (HF) in the fluids was measured by slurry pH titration method before and after the exposure. The HF concentration determined the fluoridation potential. The corrosion was mainly caused by dissolution of Fe and Cr into the fluids due to fluoridation and/or electrochemical corrosion. Carbon on the surface might be dissolved into the fluids due to the corrosion, and this resulted to the decrease of carbide on the surface. The corrosion depth of the JLF-1 specimen, which was obtained from the weight losses, was 0.637 μm in Flibe at 600 °C and 6.73 μm in Flinak at 600 °C.     

The Association of Cholesterol Uptake and Synthesis with Histology and Genotype in Cortisol-Producing Adenoma (CPA)

Cortisol-producing adenoma (CPA) is composed of clear and compact cells. Clear cells are lipid abundant, and compact ones lipid poor but associated with higher production of steroid hormones. PRKACA mutation (PRKACA mt) in CPA patients was reported to be associated with more pronounced clinical manifestation of Cushing’s syndrome. In this study, we examined the association of histological features and genotypes with cholesterol uptake receptors and synthetic enzymes in 40 CPA cases, and with the quantitative results obtained by gas chromatography-mass spectrometry (GC-MS) analysis in 33 cases to explore their biological and clinical significance. Both cholesterol uptake receptors and synthetic enzymes were more abundant in compact cells. GC-MS analysis demonstrated that the percentage of compact cells was inversely correlated with the concentrations of cholesterol and cholesterol esters, and positively with the activity of cholesterol biosynthesis from cholesterol esters. In addition, hormone-sensitive lipase (HSL), which catalyzes cholesterol biosynthesis from cholesterol esters, tended to be more abundant in compact cells of PRKACA mt CPAs. These results demonstrated that both cholesterol uptake and biosynthesis were more pronounced in compact cells in CPA. In addition, more pronounced HSL expression in compact cells of PRKACA mt CPA could contribute to their more pronounced clinical manifestation.     

Experimental study of hydrogen storage with reaction heat recovery using metal hydride in a totalized hydrogen energy utilization system

Experimental results for hydrogen storage tanks with metal hydrides used for load leveling of electricity in commercial buildings are described. Variability in electricity demand due to air conditioning of commercial buildings necessitates installation of on-site energy storage. Here, we propose a totalized hydrogen energy utilization system (THEUS) as an on-site energy storage system, present feasibility test results for this system with a metal hydride tank, and discuss the energy efficiency of the system. This system uses a water electrolyzer to store electricity energy via hydrogen at night and uses fuel cells to generate power during the day. The system also utilizes the cold heat of reaction heat during the hydrogen desorption process for air conditioning. The storage tank has a shell-like structure and tube heat exchangers and contains 50 kg of metal hydride. Experimental conditions were specifically designed to regulate the pressure and temperature range. Absorption and desorption of 5,400 NL of hydrogen was successfully attained when the absorption rate was 10 NL/min and desorption rate was 6.9 NL/min. A 24-h cycle experiment emulating hydrogen generation at night and power generation during the day revealed that the system achieved a ratio of recovered thermal energy to the entire reaction heat of the hydrogen storage system of 43.2% without heat loss.     

Thermodynamics on the Bi-Fe-Ti System and the Gibbs Energy of Bi<Subscript>9</Subscript>Ti<Subscript>8</Subscript>

Partial isothermal sections of the Bi-Fe-Ti system at 700 °C and 900 °C were constructed to investigate the reactivity of Fe with Bi-Ti liquid alloy. In the ternary system, three-phase equilibria such as liquid-Fe-Fe₂Ti, liquid-Fe₂Ti-Bi₂FeTi₄, and liquid-Bi₉Ti₈-Bi₂FeTi₄ were confirmed at both temperatures. The solubility of Fe in liquid Bi at these temperatures is negligibly small. On the other hand, it is notable that the solubility of Fe in liquid Bi containing Ti at 900 °C is much larger and reaches 2.3 mol pct. Then, we measured the electromotive force (emf) between Bi-20 mol pct Ti alloy and pure Ti at 700 °C in equimolar NaCl-KCl where 1 mol pct TiCl₂ was added. From the result, the interaction parameter of the liquid phase in the Bi-Ti system and the standard molar Gibbs energies of formation of Bi₉Ti₈ and Bi₂FeTi₄ at 700 °C were estimated.     

Compatibility of erbium oxide coating with liquid lithium–lead alloy and corrosion protection effect of iron layer

Li–Pb compatibility of Er₂O₃ and Er₂O₃-Fe two-layer coatings has been explored for an understanding of corrosion behaviors and effects of the protection layer. The coatings were peeled off after static Li–Pb immersion test at 600 °C due to the degradation of adhesion between the coating–substrate interface. A loss of Er and then subsequent corrosion of Er₂O₃ were shown after immersion at 500 °C for 500 and 1505 h. However, the outer Fe layer played a role to decrease corrosion rate of the coatings by comparing with the results of Er₂O₃ single layer coatings. Deuterium permeation measurements after corrosion tests at 500 °C showed that the Er₂O₃ coatings kept permeation reduction factors of 10²–10³ after 500 h immersion, but seriously degraded after 1505 h immersion. Corrosion mechanisms suggest that corrosion protection properties will be modified by an optimization of the outer Fe layer and a control of oxygen concentration in Li–Pb.