上海源水中DOM的分子质量及去除特性

采用分子质量排除高性能液相色谱仪 (SE—HPLC)对长江和黄浦江原水及经常规处理出水中溶解性有机物 (DOM)的分子质量分布进行了测定 ,原水中DOM分子质量分别为 80 0～ 44 0 0u和 80 0～ 1130 0u。长江原水经常规处理后的DOM分子质量分布基本不变 ,对不同分子质量的物质均有不同程度的去除 ,且分子质量越低 ,常规处理对UV2 60 的去除率也越小 ;而黄浦江原水经常规处理后有机物的分子质量分布向低分子侧推移 ,表明对大分子的去除率优于小分子 ,特别是对分子质量 <30 0 0u有机物的去除率极低。     

Fluorescent in situ hybridization analysis of open lactic acid fermentation of kitchen refuse using rRNA-targeted oligonucleotide probes

Reproducible amounts of lactic acid accumulate in minced kitchen refuse under open conditions with intermittent pH neutralization [Sakai et al., Food Sci. Technol. Res., 6, 140 (2000)]. Here, we showed that such pH-controlled open fermentation of kitchen refuse reproducibly resulted a selective proliferation of a major lactic acid bacterial (LAB) species. In one experiment, the predominant microorganisms isolated during the early phase (6 h) were Gammaproteobacteria. In contrast, those that predominated during the late phase (48 h) were always Lactobacillus plantarum in three independent experiments. To further quantify the microbial community within open lactic acid fermentation, we performed fluorescent in situ hybridization (FISH) analysis targeting 16S (23S) rRNA. We designed two new group-specific DNA probes: LAC722(L) was active for most LAB including the genera Lactobacillus, Pediococcus, Leuconostoc and Weisella, whereas Lplan477 was specific for L. plantarum and its related species. We then optimized sample preparation using lysozyme and hybridization conditions including temperature, as well as the formamide concentration and the salt concentration in the washing buffer. We succeeded in quantification of microorganisms in semi-solid, complex biological materials such as minced kitchen refuse by taking color microphotographs in modified RGB balance on pre-coated slides. FISH analysis of the fermentation of kitchen refuse indicated that control of the pH swing leads to domination by the LAB population in minced kitchen refuse under open conditions. We also confirmed that L. plantarum, which generates lactic acid in high quantities but with low optical activity, became the dominant microorganism in kitchen refuse during the late phase of open fermentation.     

Neuromelanin in Parkinson’s Disease: Tyrosine Hydroxylase and Tyrosinase

Parkinson’s disease (PD) is an aging-related disease and the second most common neurodegenerative disease after Alzheimer’s disease. The main symptoms of PD are movement disorders accompanied with deficiency of neurotransmitter dopamine (DA) in the striatum due to cell death of the nigrostriatal DA neurons. Two main histopathological hallmarks exist in PD: cytosolic inclusion bodies termed Lewy bodies that mainly consist of α-synuclein protein, the oligomers of which produced by misfolding are regarded to be neurotoxic, causing DA cell death; and black pigments termed neuromelanin (NM) that are contained in DA neurons and markedly decrease in PD. The synthesis of human NM is regarded to be similar to that of melanin in melanocytes; melanin synthesis in skin is via DOPAquinone (DQ) by tyrosinase, whereas NM synthesis in DA neurons is via DAquinone (DAQ) by tyrosine hydroxylase (TH) and aromatic L-amino acid decarboxylase (AADC). DA in cytoplasm is highly reactive and is assumed to be oxidized spontaneously or by an unidentified tyrosinase to DAQ and then, synthesized to NM. Intracellular NM accumulation above a specific threshold has been reported to be associated with DA neuron death and PD phenotypes. This review reports recent progress in the biosynthesis and pathophysiology of NM in PD.     

Profile structure of magnetic flux lines in type-II superconductor from a rectangular electron hologram

Profile magnetic configuration of a quantized flux line and flux-line lattice penetrating a type-II superconductor thin foil, niobium, was observed by electron holography and Lorentz microscopy using a 300 kV field-emission electron microscope. Each single flux line was distributed periodically as lattice structure in the mixed state just below its critical temperature of 8.5 K, while at low temperature of 5 K the flux lines were weakly bound as bundles. In order to observe the flux-line distribution over a wide area, discrete Fourier transform reconstruction in the holography was extended for a rectangular area without loss of information and data precision.     

Carbon Nitride Loaded with an Ultrafine,Monodisperse, Metallic Platinum-Cluster Cocatalyst for the Photocatalytic Hydrogen-Evolution Reaction

For the realization of a next-generation energy society, further improvement in the activity of water-splitting photocatalysts is essential. Platinum (Pt) is predicted to be the most effective cocatalyst for hydrogen evolution from water. However, when the number of active sites is increased by decreasing the particle size, the Pt cocatalyst is easily oxidized and thereby loses its activity. In this study, a method to load ultrafine, monodisperse, metallic Pt nanoclusters (NCs) on graphitic carbon nitride is developed, which is a promising visible-light-driven photocatalyst. In this photocatalyst, a part of the surface of the Pt NCs is protected by sulfur atoms, preventing oxidation. Consequently, the hydrogen-evolution activity per loading weight of Pt cocatalyst is significantly improved, 53 times, compared with that of a Pt-cocatalyst loaded photocatalyst by the conventional method. The developed method is also effective to enhance the overall water-splitting activity of other advanced photocatalysts such as SrTiO₃ and BaLa₄Ti₄O₁₅.     

Pulsed NMR study in nuclear ordered solid3He

The nuclear spin dynamics in nuclear spin ordered solid³He in low magnetic fields on the melting curve has been studied by pulsed NMR down to 0.6 mK. The free induction decay signals (FID) were measured in single crystals of solid³He at three operating frequencies of 920, 1380, and 1840 kHz. The FIDs were nonexponential and dependent on the rf pulse strength _p H ₁ t _w , where is the gyromagnetic ratio,H ₁ is the rf field strength, andt _w is the pulse width. At small _p they decayed almost linearly in time with a small exponential tail at the end. When _p was further increased they became shorter and neither exponential nor linear in time. At large _p they decayed very rapidly and sometimes could not be observed at all because of the dead time of the NMR detection system. Such behavior of the FID was observed in many different single crystals in the given temperature range at 920 kHz. Tsubota and Tsuneto have shown by solving the nonlinear equations of motion numerically that the motion of the nuclear spin becomes chaotic when the tipping angle exceeds a critical value. Comparing their result with our experimental results, we concluded that some of the results of the rapid decay of the FID at large _p might be attributed to the onset of the chaotic motion. At 1840 kHz it is expected that the nonlinear effects in the equations of motion become less effective than that at 920 kHz. In fact, at this operating frequency the FIDs even at large _p and the tipping angle-dependent frequency shift could be observed. These frequency shifts were in rather good agreement with Namaizawa's theory provided an effective tipping angle was taken into account.     

Complex impedance and admittance of a silver-conducting glass

From the analysis of complex impedance and admittance data of (Agl)₇₅(Ag₄P₂O₇)₂₅ glass, an Ag⁺-ion conductor, it was revealed that the sample can be approximated by a seriesRC ₁ circuit at high temperature, with the capacitorC ₁ arising from the charge-carrier depleted region near the anode which develops as conduction proceeds, and by a parallelRC ₂ circuit at low temperature, with the capacitorC ₂ arising from the saturated value for ionic polarization of, say, the silver-iodine pairs as well as from the relaxation effect of the Ag⁺ ions for conduction. TheC ₁ andC ₂ values were found to be almost temperature-independent at peak frequencies of the distorted semicircles in respective complex planes, with the ratioC ₁/C ₂ as large as 10⁴.     

Multipoint cure monitoring of CFRP laminates using a flexible matrix sensor

Since a carbon fiber reinforced plastic (CFRP) structure is complicated in the adoption of integral molding, local molding faults such as under curing and dry spots are liable to occur. To solve this problem, the distribution of the degree of curing for the entire composite structure must be measured. In the present study, we propose a patch-type flexible matrix sensor based on permittivity measurements. Multiple electrodes and wirings are readily fabricated simultaneously using a photolithographic process. Moreover, the sensor has only m + n wirings for m × n sensors, and is thereby suitable for multipoint cure monitoring. We also constructed a method for estimating the degree of curing considering the effect of frequency dependence of the permittivity of resin and viscosity variation due to temperature change. Experiments of multipoint cure monitoring are carried out using a CFRP plate and an actual aircraft structure. As a result, we confirmed the effectiveness of this method by comparing with results using a conventional differential scanning calorimeter.     

Sinterability of various high-purity magnesium oxide powders

The sinterability of high-purity MgO powders with different production histories was investigated to make clear the relationship between the powder characterization, the densification processes, and the changes in microstructure both with increasing temperature at a rate of 10° C min^–1 and at a fixed temperature of 1450° C for 5 h. The densification behaviour and the changes in microstructure of these compressed bodies were affected chiefly by their original surface activity and degree of agglomeration, depending on the production histories: (i) the ultra-fine and well-dispersed powder prepared by the vapour-phase oxidation process showed that densification proceeded with an appreciable grain growth with few closed pores remaining; (ii) powder derived from the sea-water magnesia process showed that the densification behaviour was affected by the species of magnesium salt, i.e. basic magnesium carbonate or magnesium hydroxide, used as a precursor; however, whichever magnesium salt was used, its sintered compact showed similar closed porosities and grain-size distributions; (iii) powder derived from the spark-discharge process contained skeletons of the original Mg(OH)₂ particles; however, the densification proceeded gradually with slow grain growth, reflecting the fact that the powder has a moderate surface area (36 m² g^–1). The sintered compact from (iii) had a small closed porosity and the smallest grain-size distribution among the compacts used in this investigation.     

Strain rate effects on viscoelastic crack bifurcation

The effects of applied strain rate on the viscoelastic crack bifurcation phenomenon in Polymethyl Methacrylate (PMMA) were investigated. It was still verified that the product $\text{σ}{}_{\mathrm{f}}\text{C}{}_{\mathrm{b}}{}^{\mathrm{<mtext>1</mtext><mtext>2</mtext>}}$ was constant, as was already observed by Congleton and Petch, and Anthony, Chubb and Congleton, for brittle elastic materials, for any strain rate, where σ_f = the gross fracture stress and C_b= the main crack length until the bifurcation starts. However, it was found that the higher strain rate increases the main crack length C_b resulting in the decrease in the gross fracture stress σ_f and vice versa. This might be interpreted that the higher stress concentration at the initiation crack tip, which is realized by becoming more brittle due to the higher strain rate owing to the predominance of the elastic element in the viscoelastic material, decreases the gross fracture stress leading to the longer main crack length.