Decreasing the number of test specimens by utilizing both fracture stress and fracture location for the estimation of Weibull parameter

In a bending load test for brittle materials, such as ceramics for spacecraft and aircraft, decreasing the number of test specimens required is a crucial problem. This paper discusses the effectiveness of using the information of both fracture stress and fracture location to decrease the number of specimens required to obtain the same precision as the Weibull estimator. The following results were obtained: It was found that by adding the fracture location information, the precision of the Weibull parameter estimation under the optimal design became 1.5–1.9 times better compared with the case of using only the fracture stresses. This means the number of samples necessary to attain the same precision becomes 1/1.5–1/1.9. Tables and figures which give information on the number of samples necessary to attain the required precision are given.     

Effects of Surface Concentration on Drying Behavior of Carbohydrate Solutions

As the surface properties of the drying materials are very important not only for the drying rate but also for the quality change during drying, the effects of surface concentration on the drying behavior of liquid foods (sugar solutions) were investigated by isothermal drying experiments and by numerical calculation experiments. The isothermal drying experiments with gelled sugar solution systems (sucrose and maltodextrin) were carried out at various relative humidity (RH) values (RH = 0 to 84%). Separate experiments were carried out for determination of the desorption isotherms.

The isothermal drying curves of sugar solutions at RH = 0 to 51% were very similar. Numerical simulations also showed that the drying curves of these sugars at the surface concentration = 0 and 0.1 are almost the same, although the concentration distributions are different.

When a small amount of gelatin was added to sugar solutions, the drying rate decreased remarkably as the gelatin might form a thin film (skin) near the surface, and consequently the retention of ethanol increased.     

Influence of protein and lipid concentration of the test lubricant on the wear of ultra high molecular weight polyethylene

To gain a better understanding of the ultra-high molecular weight polyethylene (UHMWPE) wear mechanism in the physiological environment, the effects of protein and lipid constituents of synovial fluid on the specific wear rate of UHMWPE were examined experimentally. The multidirectional sliding pin-on-plate wear tester was employed to simulate the simplified sliding condition of hip joint prostheses. Bovine serum γ-globulin and synthetic l--DPPC were used as model protein and lipid constituents of synovia, respectively. Results of the wear test indicated that the UHMWPE wear rate primarily depended on the protein concentration of the test lubricant. Lipids acted as a boundary lubricant and reduced polyethylene wear in the low protein lubricants. However, the polyethylene wear rate increased with increasing lipid concentrations if the protein concentration was within the physiological level. Increased interactions between protein and lipid molecules and lipid diffusion to polyethylene surface might be responsible for the increased wear.     

Characterization and electrochemical properties of CF4 plasma-treated boron-doped diamond surfaces

The effect of CF₄ plasma etching on diamond surfaces, with respect to treatment time, was investigated using scanning electron microscopy (SEM), Raman spectroscopy, X-ray photoelectron spectroscopy (XPS), and electrochemical measurements. SEM observations and Raman spectra indicated an increase in surface roughening on a scale of 10–20 nm, and an increase in crystal defect density was apparent with treatment time in the range of 10 s to 30 min. In contrast, alteration of the diamond surface terminations from oxygen to fluorine was found to be rather rapid, with saturation of the F/C atomic ratio estimated from XPS analysis after treatment durations of 1 min and more. The redox kinetics of Fe(CN)₆^3−/4− was also found to be significantly modified after 10 s of CF₄ plasma treatment. This behavior shows that C–F terminations predominantly affect the redox kinetics compared to the effect on the surface roughness and crystal defects. The double-layer capacitance (C_dl) of the electrolyte/CF₄ plasma-treated boron-doped diamond interface was found to show a minimum value at 1 min of treatment. These results indicate that a short-duration CF₄ plasma treatment is effective for the fabrication of fluorine-terminated diamond surfaces without undesirable surface damage.     

Active sites of Cu-ZSM-5 for the decomposition of acrylonitrile

The catalytic decomposition of acrylonitrile (AN) over Cu-ZSM-5 prepared with various Cu loadings was investigated. AN conversion, during which the nitrogen atoms in AN were mainly converted to N₂, increased as Cu loading increased. N₂ selectivities as high as 90–95% were attained. X-ray diffraction measurements (XRD) and temperature-programmed reduction by H₂ (H₂-TPR) showed the existence of bulk CuO in Cu-ZSM-5 with a Cu loading of 6.4 wt% and the existence of highly dispersed CuO in Cu-ZSM-5 with a Cu loading of 3.3 wt%. Electron spin resonance measurements revealed that Cu-ZSM-5 contains three forms of isolated Cu²⁺ ions (square-planar, square-pyramidal, and distorted square-pyramidal). The H₂-TPR results suggested that in Cu-ZSM-5 with a Cu loading of 2.9 wt% and below, Cu⁺ existed even after oxidizing pretreatment. The activity of AN decomposition over Cu/SiO₂ suggested that CuO could form N₂, but, independent of the CuO dispersion, nitrogen oxides (NO_x) were formed above 350 °C. Cu⁺ and the square-pyramidal and distorted square-pyramidal forms of Cu²⁺ showed low activity for AN decomposition. Temperature-programmed desorption of NH₃ suggested that N₂ formation from NH₃ proceeded on Cu²⁺, resulting in the formation of Cu⁺. The Cu⁺ ions were oxidized to Cu²⁺ at around 300 °C. Thus, high N₂ selectivity over Cu-ZSM-5 with a wide range of temperature was probably attained by the reaction over the square-planar Cu²⁺, which can be reversibly reduced and oxidized.     

Thermal stability of reinforced Nb3Sn composite superconductor under cryocooled conditions

Several types of reinforced Nb₃Sn wires have been developed to prevent reduction of superconducting properties by applying a strong electromagnetic force. To fabricate a cryocooled magnet using those reinforced wires, we experimentally measured the minimum quench energy (MQE) under cryocooled conditions of some reinforced Nb₃Sn wires. As a result, it became clear that thermal stability expressed as MQE was controlled by the temperature margin between the temperature of the operating condition and the transition temperature from superconductivity to normal. Using the FEM analysis, it was realized that the cause of the decline in thermal stability for the reinforced wires was the low thermal conductivity of the reinforced materials.     

Growth of Potassium Titanate Fibers in Flowing N2 Gas

The length of potassium titanate fibers produced by several conventional methods averages 50 μm, with a maximum of 100 μm. Extremely long fibers (most >1000 μm long) were obtained by calcination in N₂ gas flowing at 5.2×10^-4 m/s.     

Improved direct bonding method of Nd:YVO4 and YVO4 laser crystals

We succeeded in the fabrication of bonded laser crystals composed of a neodymium-doped YVO₄ laser crystal (Nd:YVO₄) and its host crystals YVO₄ by a newly developed dry etching technique using an argon ion beam. The optical distortion caused by the bonded interface of size 5 mm × 6 mm was estimated to be 0.05λ at 633 nm. From the comparison of laser performance pumped by a laser diode, the bonded crystals could increase the laser output power by nearly twice that of the non-bonded crystals with the same degree of polarization of 99.2%. To analyze the mechanism of the enhanced reduction of the thermal load in the bonded crystals, numerical simulations with a finite-element method were also performed.     

A study of effects of mouthwash on the human oral mucosae: with special references to sites, sex differences and smoking

Nitric oxide has been shown to decrease myocardial contractility and O2 consumption. This study was designed to evaluate the hypothesis that nitric oxide-mediated increases in cyclic GMP require elevated cyclic AMP to produce cardiac depression. Using isolated, Langendorff-perfused rat hearts, we determined the effects of intracoronary nitroprusside (NP, 1 and 10 mM) in the absence and presence of isoproterenol (ISO, 10(-8) M) on cardiac function, O2 consumption, cyclic GMP and cyclic AMP. ISO, with and without NP, increased cyclic AMP (from 287 +/- 21 to 477 +/- 33 pmol/g) without altering cyclic GMP. Left-ventricular pressure increased from 97 +/- 12 to 178 +/- 9 mm Hg and dP/dtmax from 1,786 +/- 275 to 4,049 +/- 354 mm Hg/s. NP increased cyclic GMP (from 4 to 30 pmol/g) in both the absence and presence of ISO, but NP did not alter cyclic AMP. Without ISO, NP insignificantly altered left-ventricular pressure; however, in the presence of ISO, NP significantly decreased left-ventricular pressure by -25 +/- 4 mm Hg and decreased dP/dtmax by -619 +/- 142 mm Hg/s. Isoproterenol increased O2 consumption, but the changes with NP were not significant. When this study was repeated in the presence of LY83583, a guanylate cyclase inhibitor, NP still produced cardiac depression in the presence of ISO. Therefore, cardiodepressant effects of NP were only observed against a background of inotropic stimulation with ISO. However, effects of NP on contractility were unrelated to increases in cyclic GMP or cyclic GMP-induced changes in cyclic AMP.     

Clinical and serological study of tsutsugamushi disease in northern Osumi, Kagoshima Prefecture

We report 34 cases of tsutsugamushi disease seen from 1989 to 1993 at Yagi Clinic, northern Osumi, Kagoshima Prefecture. Nineteen patients (55.9%) showed the highest antibody titers against the Kawasaki strain Orientia tsutsugamushi (Ot) and 13 (38.2%) against the Kuroki strain Ot. It is suggested that two antigenic types (Kawasaki and Kuroki) of Ot were distributed in Kagoshima Prefecture, and the Kawasaki type Ot more or less dominates Kuroki type Ot. There was no difference in clinical features between the two groups of patients.