Finishing of glass-ionomer cement (SEM study)

A total of 12 glass-ionomer cement specimens were utilized in the present study. The specimens were divided into two equal groups. The first group was used after 10 minutes from setting, while the second was utilized after 24 hours from setting. Each group was divided into three equal subgroups (2 specimens each). The first subgroups were finished under wet condition (wet finished). The second subgroups were dry finished. On the other hand, the third subgroups were kept undisturbed (as set) under mylar strips. The specimens surfaces were then examined by a Scanning Electron Microscope (SEM). It was found that, finishing of the specimens after 24 hours from setting demonstrated more acceptable surface topography either in wet or dry conditions than finishing after 10 minutes from setting. Moreover, the dry finished specimens displayed more acceptable surface topography than the wet finished specimens. On the other hand, the as set (undisturbed) specimens the most acceptable surface topography.     

A novel interference suppression scheme for global navigation satellite systems using antenna array

This paper considers interference suppression and multipath mitigation in Global Navigation Satellite Systems (GNSSs). In particular, a self-coherence anti-jamming scheme is introduced which relies on the unique structure of the coarse/acquisition (C/A) code of the satellite signals. Because of the repetition of the C/A-code within each navigation symbol, the satellite signals exhibit strong self-coherence between chip-rate samples separated by integer multiples of the spreading gain. The proposed scheme utilizes this inherent self-coherence property to excise interferers that have different temporal structures from that of the satellite signals. Using a multiantenna navigation receiver, the proposed approach obtains the optimal set of beamforming coefficients by maximizing the cross correlation between the output signal and a reference signal, which is generated from the received data. It is demonstrated that the proposed scheme can provide high gains toward all satellites in the field of view, while suppressing strong interferers. By imposing constraints on the beamformer, the proposed method is also capable of mitigating multipath that enters the receiver from or near the horizon. No knowledge of either the transmitted navigation symbols or the satellite positions is required.     

KINEMATIC VISCOSITY-TEMPERATURE BEHAVIOR OF HEAVY TBP-FRACTIONS (455°C+) OF ARABIAN CRUDE OILS

A generalized kinematic viscosity-temperature correlation for undefined liquid heavy petroleum fractions has been developed to represent the data for a wide range of temperature from 100°C to 200°C. The correlation is based on the experimental kinematic viscosity data of true boiling point fractions of four Arabian crude oils. The characterization property required for estimation is 50% boiling point. The proposed correlation fits the experimental data with an overall absolute error of 6.1%. Experimental measurements of kinematic viscosity of heavy true boiling point fractions of Arabian crude oils were also obtained in order to develop the proposed correlation.     

An extended minimax disparity to determine the OWA operator weights

This paper contributes to extend the minimax disparity to determine the ordered weighted averaging (OWA) model based on linear programming. It introduces the minimax disparity approach between any distinct pairs of the weights and uses the duality of linear programming to prove the feasibility of the extended OWA operator weights model. The paper finishes with an open problem.     

Smart home security: challenges,issues and solutions at different IoT layers

The Journal of Supercomputing - The Internet of Things is a rapidly evolving technology in which interconnected computing devices and sensors share data over the network to decipher different...     

Preparation of heavily dopedn-type Ge-Si thermoelectric alloys

Germanium-silicon alloys doped with phosphorus were prepared in vacuum by rapidly pouring the molten alloy into cooled copper moulds containing the phosphorus dopant. Without any further treatment, the ingots are milled into powder of grain size (L 5 µm) and hot pressed. It is shown that a high degree of homogenization of the alloy constituents can be obtained in the final compacts, thus eliminating the need for zone-levelled starting material. It is also shown that this work is in agreement with the plastic flow model of sintering known as the Mackenzie-Shuttleworth-McClelland model. Electrical measurements indicate that the dopant is effectively and uniformly incorporated into the alloy.     

Thermoelectric properties of fine grained (75% Sb2Te3-25% Bi2Te3)p-type and (90% Bi2Te3-5% Sb2Te3-5% Sb2Se3)n-type alloys

The thermoelectric properties of fine-grained alloys prepared by either cold pressing and sintering or hot pressing in the range 5–50 m are compared with single-crystal best-direction values. It is shown that for thep-type alloy, almost the entire thermoelectric properties are recovered, i.e. the figure of merit for the finest grain size is almost the same as the best single-crystal value. The same trend is observed in then-type alloy except that 90% of the single-crystal figure of merit is recovered. These results are discussed in terms of a model which suggests that degradation of favourable thermoelectric properties by powdering the alloys is compensated by (1) decrease of thermal conductivity due to scattering of phonons at grain boundaries for grain sizes that are comparable to the mean free path of phonons; and (2) retention of some of the anisotropic properties of the single crystal in the fine-grained compacts.     

Design of Dual-Gate P-type IMOS Based Industrial Purpose Pressure Sensor

Silicon - In this treatise, we have proposed a Single Material Gate–Dual Gate Impact Ionization Metal Oxide Semiconductor (SMG DG-IMOS) based Pressure Sensor. The pressure sensor has the most...     

Piezoresistivity in Polymer-Ceramic Composites

Composite materials composed of randomly dispersed semiconducting ceramic particles in an insulating polymer matrix show a pronounced change in resistivity with pressure. Different amounts of iron oxide (Fe₃O₄) powder and antimony-doped tin oxide (SnO₂:Sb) powder were dispersed in an epoxy polymer matrix to form pressure-sensitive composites. In each family of materials, an insulator-to-semiconductor transition is observed in agreement with percolation theory. Composites within a certain range of filler content showed substantial piezoresistive effect under both uniaxial and hydrostatic pressure in which sensitivity is controlled by the choice of filler material and the volume fraction. The effect of temperature on the piezoresistance effect was also examined. Piezoresistors made from Fe₃O₄ composites showed larger temperature changes than those filled with Sb-doped SnO₂.     

Weight loss, polarization, electrochemical impedance spectroscopy, SEM and EDX studies of the corrosion inhibition of copper in aerated NaCl solutions

This work reports results of weight loss, potentiodynamic polarization and impedance measurements on the corrosion inhibition of copper in aerated non-stirred 3% NaCl solutions in the temperature range 15–65 °C using sodium oleate (SO) as an anionic surfactant inhibitor. These studies have shown that SO is a very good ”green”, mixed-type inhibitor. The inhibition process was attributed to the formation of an adsorbed film on the metal surface that protects the metal against corrosive agents. Scanning electron microscopy (SEM) and energy dispersion X-ray (EDX) observations of the electrode surface confirmed the existence of such an adsorbed film. The inhibition efficiency increases with increasing surfactant concentration and time of immersion, while it decreases with solution temperature. Maximum inhibition efficiency of the surfactant is observed at concentrations around its critical micellar concentration (CMC). The potential of zero charge (pzc) of copper was studied by ac impedance, and the mechanism of adsorption is discussed. The sigmoidal shape of the adsorption isotherm confirms the applicability of Frumkin’s equation to describe the adsorption process. Thermodynamic functions for the adsorption process were determined.