Comparative study of the colorants monascus and cochineal used in the preparation of gels made with various gelling agents

The possibilities of using monascus to colour gels were studied by comparing it with cochineal. Gels were prepared with four gelling agents—carrageenan, gellan, gelatine and xanthan—and their colour was measured with a Hunter Lab colorimeter. The equations relating L^* and h with the concentrations of sugar [SU] and colorant [COL] were deduced, and it was found that [COL] had more influence on colour than [SU]. In general, for these four gelling agents the colour of monascus gels is orange-red and the colour of cochineal gels is purplish red. The gels made with xanthan were always the lightest, whether they were made with cochineal or with monascus.     

Preparation and characterization of chitosan‐based dispersions

Complexation of chitosan in aqueous solutions by low molecular weight electrolytes is one of the simplest methods for the preparation of aqueous chitosan dispersions. In this work, the influence of storage time, sulfate concentration, method of preparation and surfactant content on some properties of the resultant chitosan dispersions (turbidity, viscosity and zeta potential) was analyzed. Turbidimetry was adequate to monitor the formation of particles, while viscometry was suitable to monitor changes in the dispersing phase. An analysis of the properties of these systems, mainly in terms of particle–particle and macromolecule–macromolecule interactions was carried out. Copyright © 2004 Society of Chemical Industry     

Influence of the ethylene–(methacrylic acid)–Zn2+ ionomer on the thermal and mechanical properties of blends of poly(propylene) (PP)/ethylene–(vinyl alcohol) copolymer (EVOH)

The thermal and mechanical properties and the morphologies of blends of poly(propylene) (PP) and an ethylene–(vinyl alcohol) copolymer (EVOH) and of blends of PP/EVOH/ethylene–(methacrylic acid)–Zn²⁺ ionomer were studied to establish the influence of the ionomer addition on the compatibilization of PP/EVOH blends and on their properties. The oxygen transmission rate (O₂TR) values of the blends were measured as well. PP and EVOH are initially incompatible as was determined by tensile tests and scanning electronic microscopy. Addition of the ionomer Zn²⁺ led to good compatibility and mechanical behaviour was improved in all blends. The mechanical properties on extruded films were studied for 90/10 and 80/20 w/w PP/EVOH blends compatibilized with 10 % of ionomer Zn²⁺. These experiments have shown that the tensile properties are better than in the injection‐moulded samples. The stretching during the extrusion improved the compatibility of the blends, diminishing the size of EVOH domains and enhancing their distribution in the PP matrix. As was to be expected, the EVOH improved the oxygen permeation of the films, even in compatibilized blends. Copyright © 2004 Society of Chemical Industry     

Rheological and drug‐release behaviour of a scleroglucan gel matrix at different drug loadings

The aim of this study was to investigate the drug‐loading effects on release and mechanical properties of a scleroglucan gel, with the intention of considering them in delivery systems formulations. The rheological and kinetic properties of a 2 % w/w scleroglucan gel matrix loaded with 0, 0.02, 0.04, 0.06, 0.2 and 0.4 % w/w of theophylline (Th, used as a model drug) were investigated. Rheological measurements were performed in a controlled‐stress rotational‐shear rheometer under isothermal conditions. For theophylline release from the gel a flat Franz cell was used and the kinetic parameters were derived applying a semi‐empirical power law. The influence of scleroglucan molar weight on kinetic and rheological behaviour was also studied. Results suggest two possible effects of drug loading on the gel network: in the 0.04–0.06 % w/w Th range a plasticizing effect and in the 0.2–0.4 % w/w Th range a rigidization effect. In the first range mentioned, the changes in the gel structural properties tested by means of rheological measurements are coincident with changes in drug‐release kinetics. Copyright © 2005 Society of Chemical Industry     

A time series bootstrap procedure for interpolation intervals

A sieve bootstrap procedure for constructing interpolation intervals for a general class of linear processes is proposed. This sieve bootstrap provides consistent estimators of the conditional distribution of the missing values, given the observed data. A Monte Carlo experiment is used to show the finite sample properties of the sieve bootstrap and finally, the performance of the proposed method is illustrated with a real data example.     

Elimination of organic matter present in wastewaters from the cork industry by membrane filtration

BACKGROUND: The first stage of the cork industrial process generates great volumes of wastewater with moderate to high organic pollutant content that must be purified using different procedures, such as filtration by membranes. RESULTS: The tangential filtration of these wastewaters was studied using two different laboratory equipments. In the first one, three ultrafiltration (UF) membranes were tested, with molecular weight cut‐off (MWCO) 100 kDa and 30 kDa, and two operating modes were used: total recycling of permeate and retentate streams, and in continuous mode, without recycling both streams. In the total recycling UF experiments, the influence of the operating variables on the permeate flux was first established. The effectiveness of the different membranes was determined by evaluating the rejection coefficients for several parameters that measure the global pollutant content of the effluent. The values found for these rejection coefficients were in the following order: ellagic acid and color > absorbance at 254 nm > tannic content > COD (chemical oxygen demand). In the continuous mode experiments, the fouling mechanism for each membrane was established by fitting the experimental data to various filtration fouling models given in the literature. The operating mode in the second equipment was batch concentration, and additional experiments were carried out with an UF membrane (2 kDa), and with a NF membrane (with MWCO in the range 150–300 Da). CONCLUSIONS: The three operating modes tested provided different rejection levels of organic matter; among them, the most effective procedure tested was batch concentration mode using a NF membrane. Copyright © 2007 Society of Chemical Industry     

Sequential batch reactor for eucalypt kraft pulp effluent treatment with Trametes versicolor

BACKGROUND: A sequential batch reactor (SBR) was used for eucalypt kraft pulp effluent treatment with Trametes versicolor. A 2³ full factorial design and response surface methodology were applied to optimise the batch fermentation conditions. Effluent concentration, culture medium and inoculum age were the factors selected for this study in order to optimise the reduction of chemical oxygen demand (COD). RESULTS: The presence of Trametes Defined Medium (TDM) in the fermentation was required to obtain a significant COD reduction. Experiments in the batch reactor confirmed, in general, the predicted results of optimisation developed from Erlenmeyer batch assays. The T. versicolor culture remained active during 42 days of study in the SBR, providing approximately 80% of COD reduction. CONCLUSION: Trametes versicolor may be considered as very promising for the biological treatment of effluents from kraft pulp mills in an SBR system instead of the activated sludge mixed cultures traditionally used. Copyright © 2008 Society of Chemical Industry     

Xylene Isomerization in a ZSM-5/SS Membrane Reactor

A membrane reactor containing different types of ZSM-5/porous SS membranes was used to perform the xylene isomerization reaction. The parent Na-ZSM-5 layer was synthesized by secondary growth on top of porous stainless steel tubes. The xylene isomerization reaction was carried out at different temperatures in the membrane reactor and in a fixed-bed reactor of identical geometry for comparison. Two different kinds of membranes were prepared by ion exchange: a Pt/H-ZSM-5 catalytic membrane and two Ba-ZSM-5 composites with different Ba²⁺ concentration. The p-xylene production using 100% exchanged Ba-membrane was about 28% higher than the fixed-bed reactor at 370 °C, when m-xylene was fed.     

Fullerene Reactivity in an Oxygen Plasma

Fullerene reactivity in an oxygen plasma was measured and compared with those determined under the same conditions for a comprehensive set of 50 carbon materials. The possible reasons for the high plasma reactivity of the fullerene sample in an oxygen plasma are discussed.     

Intrauterine transfusions influence fetal leukocyte counts and subsets

Histamine is an important mediator in allergic reactions, gastric acid secretions, and neurotransmission in the central nervous system. Basophils and mast cells are the main sources of histamine, which is formed from L-histidine by histidine decarboxylase (HDC). However, the regulatory mechanism of HDC in these cells remains unclear. We examined the regulation of HDC activity and gene expression using a unique human mast cell line, HMC-1, after stimulation with phorbol 12-myristate 13-acetate (PMA) or ionomycin. HDC activity was increased from 52.1+/-0.4 (mean+/-standard deviation) to 154+/-6.9, or 105.6+/-6.2 pmol/min/mg protein (n = 3), 4 hours after stimulation with PMA (10 ng/mL) or ionomycin (10[-6] M). Although actinomycin D had no effect on this increase, cycloheximide completely inhibited the increase caused by these stimuli. The population of HMC-1 cells containing HDC protein was increased after stimulation with either PMA or ionomycin as evaluated by immunocytochemical analysis with anti-HDC antibody as a marker. HMC-1 constitutively expressed HDC mRNA, and its level was not increased with these stimuli. These results suggest that the increase of HDC activity in HMC-1 induced by PMA or ionomycin is regulated at the translational level.