The 20th century whole-basin trophic history of an inter-drumlin lake in an agricultural catchment

Eight 1-m sediment cores were extracted from across the basin of Friary Lough, a 5.4-ha eutrophic lake in a wholly grassland agricultural catchment in Co. Tyrone, Northern Ireland. Sedimentary TP, diatom inferred TP, Ca, Na, Fe, Mn, loss-on-ignition (LOI), dry weight and density were determined in the core profiles. Core dating and correlation gave a 210Pb, 137Cs and 241Am chronology from 1906 to 1995 and enabled a whole-basin estimate of chemical and sediment accumulation rate over the 20th Century. The major changes for all parameters occurred after c. 1946. Sediment accumulation rate was most influenced by organic matter accumulations, probably of planktonic origin, and increasing after c. 1946. Inorganic sediment accumulation rate was found to be largely unchanging through the century at 10 t km(-2) yr(-1) when expressed as catchment exports. All chemical accumulation rate changes occurred after c. 1946. Total phosphorus accumulation rate, however, was found to be the only chemical to be increasing throughout the epilimnion and hypolimnion areas of the sedimentary basin at an average of 22.5 mg m(-2) yr(-1) between 1946 and 1995. The other chemical parameters showed increasing accumulation rates after c. 1946 in the epilimnion part of the basin only. Interpreted in terms of whole-basin sedimentation and catchment export processes over time, it is suggested that diffuse TP inputs are independent of sediment inputs. This corresponds to hydrochemical models that suggest soluble P as the primary fraction that is lost from grassland catchments. The increase in sedimentary TP accumulation rate, and DI-TP concentration, are also explained with regard to current models that suggest increases in runoff P concentrations from elevated soil P concentrations. Increases in eplimnion chemical and sediment accumulation rate after c. 1946 may be due to local erosion that has limited impact on lake basin sedimentation.     

ASSESSING AND MANAGING THE RISKS OF PATHOGEN TRANSFER FROM LIVESTOCK MANURES INTO THE FOOD CHAIN

A review was undertaken of (a) the levels and prevalence of Salmonella spp., Campylobacter spp., Listeria monocytogenes, Escherichia coli 0157. Cryptosporidium parvum and Giardia intestinalis in livestock manure, and (b) factors which affect their survival during storage and following land application. Pathogens are commonly present in livestock manures and can survive in soil for several months or years after spreading or excretion onto land. Temperature was identified as being the most important factor influencing pathogen survival, although pH, UV light and drying were also important. Various practical measures to minimise the risk of pathogen transfer into the food chain were identified, including treatment, extended storage and no/harvest periods following land spreading. Guidelines are being developed on managing farm manures to minimise the risks of microbiological contamination of ready-to-eat crops.     

Use of driven piles in rammed holes during construction in soils prone to slump-type settlement

Conclusions The experiment with the use of piles cast in rammed holes in lieu of continuous foundations placed on a bed compacted by tamping produced positive results and will be expanded upon further, since the strength properties of the materials in the foundations and the soils in the foundation beds can be more fully utilized, the reliability of the structure increased, the volume of earthwork reduced, labor and material outlays diminished, and the rate of construction and the level of the industrial nature of the work increased.State Institute for the Projection of the Greenhouse Industry. Translated from Osnovaniya, Fundamenty i Mekhanika Gruntov, No. 2, p. 10, March–April, 1977.     

Finite element modelling of plate girders with web openings

This paper is concerned with a finite element model to predict the behaviour and ultimate load of plate girders with web openings. The finite element package is used to model the plate girders with web openings. Accuracy of the model is assessed by applying it to plate girders tested earlier by other researchers. Comparison of analytical results with the available experimental results for yielding patterns, ultimate load values and load–deflection relationships show good agreement between the finite element and experimental results thus validating the accuracy of the proposed model. The proposed finite element method was extended to carry out a parametric study. The study covered parameters such as web slenderness and flange stiffness.     

Design Water Levels in Tidal River Systems under the Influence of Typhoons

Water levels in tidal rivers are subject to the influence of both fluvial and tidal factors. The interaction between these factors is rendered more complex in regions affected by typhoons, which typically result in the combined occurrence of heavy rainfall and high sea levels.
Previous studies have outlined an analytical approach for calculating design water levels based on dividing the fluvial and tidal series into a typhoon and a non-typhoon component. This paper illustrates the steps involved in the analytical approach and describes its application to drainage basins in Hong Kong.
The approach provides a practical means for calculating design water levels, and is recommended for final design purposes. The results of using the full analysis may be approximated by using a sub-set of analytical results, and should prove satisfactory for the purposes of outline design.     

Compartment tests of polyurethane foam seating assemblies

Data from compartment tests of polyurethane foam seating assemblies are reported. Results show that the behavior of such assemblies during fires is strongly dependent on the type and position of interliners and upholstery fabrics. An incidental comparison of peak rate of heat release obtained in a compartment test with a predictive model equation is made and selected data from the tests are presented.     

Contribution à l'étude de la détermination des conditions de formation des haloformes

In recent years the presence of haloforms has been observed by some researchers in waters of various origins.The aim of this study is to determine the conditions in which chloroform is formed by chlorination of aqueous solutions of some organic compounds.The first part of this work was carried out by chlorination of synthetic basic solutions of acetone and thus enabled us to determine the reagent concentrations needed to obtain the maximum quantity of chloroform.We studied next the effect of chlorination on organic material solutions (humic acids and phenols), in the course of an oxidation treatment; the results obtained by chlorination of aqueous solutions of humic substances show that the quantity of chloroform produced passes through a maximum value which depends on the time of ozonisation. Similar results were obtained for the chlorination of phenol solutions during oxidation by the u.v. + H₂O₂ system. These results may be explained by the partial degradation of the molecules which leads in the formation of reactional intermediate precursors of the haloform reaction. We undertook at the same time the study of a rapid test allowing us to detect the presence of haloform reaction precursors in a certain sample of water.     

Settlements and deformations of industrial structure built on weak soils

Conclusions 1. In engineering-geologic explorations, it is necessary to investigate the engineering-geologic morphology to a depth of 15–18 m: lenses and interlayers of weak soils - unevenly compacted silty-sand fills, peat, slime, etc.2. Open unwatering of pits in the vicinity (10–15 m) of existing structures is impermissible, since it leads to removal of fine soil fractions because of piping, and to large and impermissible deformations of the load-bearing elements of the structures. In such cases, deep groundwater lowering by means of wellpoints should be used.In the case described in this article, the industrial structure underwent a mean settlement of about 20 cm, a tilt of 0.015, and a wall deflection of 0.002. By using deep groundwater lowering, such deformations could have been prevented.3. The development of settlements with time was due to the presence of weak soils - peat lenses and thin slime interlayers - in the foundation bed of the shop.4. An effective means for stopping the settlement of the industrial structure was the construction, under the walls, of two rows of cast-in-place piles with cantilever beams to which the wall loads were transmitted.Scientific-Research Institute of Foundations. GIPROLESKhIM. Translated from Osnovaniya, Fundamenty i Mekhanika Gruntov, No. 1, pp. 5–7, January–February, 1975.     

Dynamic analysis and optimal feedback control synthesis applied to biological waste treatment

The dynamics and optimal feedback control of biological waste treatment processes are examined. Modern feedback control theory is applied and results are obtained for both proportional and proportional plus integral control. A dynamic mathematical model of the system is developed by employing a Monod kinetic model, which is modified to account for endogenous metabolism, and a complete mixing flow model in the growth chamber. The feedback control is implemented via the flow rate so as to maintain desired effluent concentrations. External disturbances which cause changes in substrate concentration and/or cell concentration are considered and optimal control effort is applied. Results are also presented for impulse and step changes in the influent substrate concentration. It is found that by changing the values of the weighting factors in the objective function, it is possible to obtain good control of either the effluent substrate concentration or cell concentration.     

The development of macrolayer thickness of water in the pool boiling regime

ABSTRACT

The main purpose of this study is to analyse the phenomenon of pool boiling in water over a horizontally placed copper tube heater of 28?mm diameter. The experiment has been carried out to observe the bubble growth and departure characteristics for the heat flux range up to 40,000?W/m². The entire process is being recorded by a digital camera at different time intervals. The measured parameters have been used to determine the initial layer thickness, macro layer thickness and critical heat flux and validated with models proposed in the literature.