高水头混流式水轮机内部固液两相流数值分析

针对泥沙直径对混流式水轮机蜗壳和导水机构内部流场产生影响的问题进行了初步研究,采用固液两相流模型对某电站的高水头混流式水轮机进行了全流道数值模拟,通过单一变量法来研究不同来流泥沙的直径对蜗壳和导水机构内部压力及泥沙分布产生的影响。研究结果表明:与清水相比,含沙水流会不同程度地使蜗壳和导水机构内部的水压力载荷增加,在相同工况下,蜗壳底部、蜗壳鼻端、固定导叶和活动导叶头部的泥沙浓度较大;小直径下泥沙分布均匀,随着泥沙直径的增加,泥沙浓度的梯度变大,泥沙分布更加集中,从而会使磨损加剧。该研究成果可为在含沙水流中运行的水轮机设计提供参考。     

基于逐次散射法的海洋-大气矢量辐射传输模式

首先推导了粗糙洋面双向偏振反射模型pBRDF(Bidirectional Polarized Reflectance Distribution Function),并将其与SOSVRT(Successive Order of Scattering Radiative Transfer)矢量辐射传输模式耦合,建立了海洋-大气耦合的矢量辐射传输模式,并对该耦合模式的模拟结果与前人模拟结果进行对比,验证了该耦合模式的可靠性与有效性。不同大气和洋面状态、不同高度的主平面内辐射强度和偏振度的模拟结果表明:pBRDF模型可以很好地模拟不同风速下洋面的偏振反射分布特征;洋面在特定角度具有很高的偏振度,并对大气顶的偏振辐射有很大影响。因此,该耦合模式可以更准确地处理辐射光谱在海洋-大气两种介质间的传输问题,对矢量辐射传输、大气遥感问题的研究有重要意义。     

浅谈多媒体教学以信息管理中心为例

高职教育的特点就是以适应社会需要为目标、以培养技术应用能力为主线设计学生的知识、能力、素质结构和培养方案,毕业生应具有基础理论知识适度、技术应用能力强、知识面较宽、素质高等特点.以“应用”为主旨来构建课程和教学内容体系.     

乙烯二聚制高纯丁烯－1技术经济评价

本文对生产高纯度丁烯－１的Ａｌｐｈａｂｎｔｏｌ工艺进行了技术经济评价，认为该工艺条件简单、反应条件温和，而且投资少，所以很适合事在发展中国家应用。     

A low‐profile antenna with circularly polarized reconfigurable and omnidirectional radiation patterns

A low profile circularly polarized (CP) antenna with reconfigurable polarization is designed and presented, which can radiate omnidirectional patterns that can be switched between left‐hand circularly polarized (LHCP) and right‐hand circularly polarized (RHCP). A pair of arc‐shaped complementary dipoles is acted as reconfigurable elements by bridging four pin diodes at the dipole arced arms. A meander phase shift line is employed to connected the arc dipole arms and plate cavity to adjust the phase relationship of two sources. The proposed antenna exhibits the omnidirectional radiation pattern by combining six identical elements placed in a circular array configuration. 24 p‐i‐n diodes are exploited to six elements, by manipulating the dc bias voltage across the diodes, the polarization state of the antenna can be switched. The patterns of the antenna are similar to that of a dipole, but its size is only about Φ0.87 × 0.029λ₀ at 5.8 GHz. The overlapped bandwidth of measured 3‐dB axial ratio (AR) and 10‐dB return loss is 5.724‐5.87 and 5.738‐5.91 GHz for two polarization states, which are right on the target of ISM band. It can be well adapted to medical diagnosis systems.     

基于MEMS电容式加速度计的闭环读出电路设计

设计了面向圆片级封装的一种闭环加速度计读出电路.在基于电容式微加速度计结构的读出电路设计中考虑了寄生电容对整个系统的影响.用MATLAB SIMULINK对所设计的读出电路进行了建模仿真.在仿真过程中分析了噪声、圆片级封装与普通封装的寄生参数及实际工艺中流水结构的不对称性的影响并进行了比较.结果表明,所设计传感器及读出电路的非线性误差在量程±20 gn范围内小于0.5％;圆片级封装的稳定时间在2 ms,小于普通封装的稳定时间;基于圆片级封装的对称性梳齿结构的输出电压灵敏度为328 mV/gn.     

基于ZYNQ飞艇囊体应变在线监测系统设计

针对当前高空飞艇囊体的应变实时测量装置无法同时具备体积小和实时测量的工作属性,创新性地用光学器件和感光元件配合,对工作中飞艇囊体两个固定点的相对位移量进行测量,提出了一种能够在线监测飞艇囊体应变的测量装置,能够实现应变在线测量且测量精度高;采用TCD1500C电荷耦合器件作为数据来源;主芯片采用ZYNQ处理器,ZYNQ能够具备FPGA的并行处理能力和Cortex的数据调度能力,能够处理CCD高速数据;通过自定义IP核,使用PS端与PL端互联AXI协议,实现了高速、大量数据传输;为了得到应变信号,采用了将应变信号转化为位移信号进行采集的方法,之后将位移信号采集存储至SD卡中并周期性显示到上位机上,实现地面对飞艇囊体应变的实时监控;实现了飞艇囊体应变的实时测量并把测量精度提高至0.1％.     

冶炼不锈钢泡沫渣的实验研究

从理论上阐述冶炼不锈钢时熔渣的发泡机理。并根据上海三钢公司的情况，在2500Hz的中频感应炉上时熔渣进行发泡高度的实验，找出发泡性能较好的渣系，研究渣中各成分对发泡性能的影响。     

Fuzzy adaptive networks in machining process modeling: surface roughness prediction for turning operations

Due to the complexity of the machine tool structure and the cutting process, the dynamics of machining processes are still not completely understood. This is especially true due to the demand of high-speed machining to increase productivity. In order to model and control these complex processes, new approaches, which can represent complex phenomenon combined with learning ability, are needed. The combined neural–fuzzy approach appears to be ideally suited for this purpose. In this paper, the recently developed fuzzy adaptive network (FAN) is used to model surface roughness in turning operations. The FAN network has both the learning ability of neural network and linguistic representation of complex, not well-understood, vague phenomenon. Furthermore, it can continuously improve the initially obtained rough model based on the daily operating data. To illustrate this approach, a model representing the influences of machining parameters on surface roughness is established and then the model is verified by the use of the results of pilot experiments. Finally, a comparison with the results based on statistical regression is provided.     

移动图形处理器的现状、技术及其发展

3D图形绘制技术已经渗透到各种移动设备中.相对于桌面PC,移动设备图形处理需要以更低的功耗、更有限的内存带宽和较低的运算能力实现高性能、高质量的图形显示效果.文中介绍了移动图形处理器发展现状,从硬件设计方面分析了这一领域未来面临的挑战;分析了当前移动图形处理器中区块式和立即式渲染的架构特点,总结了渲染过程中加速数据流计算方法和芯片低功耗设计方法.最后展望了移动图形处理器的发展趋势.